Installation Guide for HOOKE ROAD models including: BXG.4227-S, BXG.4227-S Front Bumper, BXG.4227-S, Front Bumper, Bumper
Hooke Road Bumper Installation Instructions | Installation Manual – Hooke Road 4x4
MAKEA DIFFERENCE Fr ont Bum per BXG.4227-S (INSTALLATION INSTRUCTION) Please verify all parts are present and read instructions carefully before starting installation. Please feel free to contact your distributor if you have any kind of question about your purchase. 1 CONTENTS Left Right E1 F1 E2 F2 A1 A2 B C D B: Main Body A1&A2: Wings E1&E2: Decorative Accessories Qty Part Name Size(mm) Picture 8 Hex Bolt M10*25 C: License Plate Bracket D: Skid Plate F1&F2: Fixing Brackets Qty Part Name Size(mm) Picture 6 Flat Washer M8*20*1.5 6 Button Bolt M8*20 4 Flat Washer M6*16*1.5 2 Button Bolt M6*16 2 Flat Washer M6*16*1 4 Button Bolt M6*12 2 Phillips Screw M4*14 8 Split Lock Washer D10 2 Hex Nut M10 2 Flange Hex Lock Nut M8 2 Flange Hex Lock Nut M6 10 Flat Washer 2 EVA M10*25*2 1 Rubber Strip 3M 2 TOOLS REQUI RED View electronic pdf, please To view onslcinaen itnhsetrQuRctcioond,ep.lease scan the QR code. Drive Ratchet Handle 14mm, 17mm Wrench 4mm, 5mm Hex Bit Socket If want to the view electronic pdf, please scaPnhtilhliepsQSRcrceowdderi.ver 3 I NSTALLATI ON I NSTRUCTI ON St ep 1 Place the vehicle in park and remove the factory bumper from the frame. Keep the factory screws and nuts. St ep 1 3 3 1 2 St ep 2 Use the provided fixing bracket to connect the grille to the vehicle. Use the factory bolts and screws or the provided phillips screws. Repeat this step for the opposite of the vehicle. Tighten up all bolts and screws. 3 1 2 St ep 3 Stick the EVA to the bumper and install the left wing to the main body using (3) M10x25mm hex bolts, (3) D10 lock washers, (3) M10x25x2mm flat washers. Repeat this step for the opposite of the bumper. Tighten up all bolts. St ep 6 Install the bumper to the vehicle using the factory nuts. Repeat this step for the opposite of the bumper. Adjust the bumper to the desired location. Tighten up all bolts. 1 1 St ep 4 Install the decorative accessory to the left wing using (2) M6x12mm button bolts, (2) M6x16x1.5mm flat washers. Repeat this step for the opposite of the bumper. Tighten up all bolts. St ep 7 Install the skid plate to the bumper using the (4) M8x20mm button bolts, (4) M8x20x1.5mm flat washers. Do not tighten the hardware at this time. St ep 5 Install the license plate bracket to the bumper using the (2) M8x20mm button bolts, (2) M8x20x1.5mm flat washers, (2) M8 flange lock nuts. Tighten up all bolts. St ep 8 Connect the skid plate and the frame of vehicle using the (1) M10x25mm hex bolts, (1) D10 lock washers, (2) M10x25x2mm flat washers, (1) M10 hex nuts. Repeat this step for the opposite of the bumper. At last, tighten up all bolts. 2 St ep 9 The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product! to find your parts. Feel Free To Share Your Vehicle @HookeRoad4x4 With The Hashtag #hookeroad If You'd LikeAdobe Illustrator 28.0 (Windows) iLovePDF