IKEA MALM Chest of Drawers

Important Safety Information

⚠️ WARNING: Furniture tip-over can cause serious injury or death.

To reduce the risk of furniture tipover:

• ALWAYS install the anti-tip device provided. [wall anchor symbol]
• NEVER place a television on this product.
• NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• DO NOT defeat or remove the drawer interlock system; it is an important stability and safety system.
• Place heaviest items in the lowest drawers.

Tools Required

• Screwdrivers (Phillips and flathead)
• Hammer
• Drill
• Drill bits: Ø 5/16" (8 mm) and Ø 1/8" (3 mm)

Parts Identification

The assembly requires various components. Key hardware items and their approximate quantities are listed below. Refer to the original diagrams for exact identification and placement.

• Cam Locks: 16x
• Dowels: 16x
• Screws: Various types and quantities (e.g., 8x, 18x, 12x, 4x, 2x, 1x)
• Drawer Slides: 3x sets (for drawers)
• Handles: 3x
• Anti-tip Hardware: 2x sets (brackets, straps, screws, wall plugs)
• Drawer Bottoms: 3x
• Drawer Sides, Backs, Fronts: Multiple pieces for 3 drawers
• Main Frame Panels: Top, bottom, and side panels
• Vertical Supports: Multiple pieces
• Rear Support Rail: 1x

Assembly Steps

1. Step 1-2: Frame Base and Sides

   Attach the side panels to the base and top panels using cam locks and dowels. Insert dowels into pre-drilled holes and secure with cam locks. Mount the drawer runners to the inner sides of the main frame using screws.

2. Step 3: Drawer Box Construction

   Assemble the three drawer boxes. Connect the drawer sides, back, and base panels using dowels and screws. Ensure the grooves for the drawer bottom are aligned.

3. Step 4-6: Vertical Supports Installation

   Insert vertical support pieces into the designated holes on the base panels of the main frame.

4. Step 7-8: Attaching Main Side Panels

   Slide the main side panels onto the assembled frame, aligning them with the base and top panels. Secure these panels using cam locks.

5. Step 9-10: Rear Support Rail Attachment

   Attach the rear support rail to the top rear of the frame. This typically involves brackets and screws.

6. Step 11-13: Securing the Top Panel

   Place the top panel onto the assembled frame. Secure it from underneath using cam locks and screws.

7. Step 14-15: Drawer Front Attachment

   Attach the drawer fronts to the assembled drawer boxes. This usually involves screws inserted from the inside of the drawer box.

8. Step 16-17: Drawer Runner Installation on Drawers

   Attach the corresponding drawer runners to the sides of the assembled drawer boxes. Ensure they are oriented correctly for smooth operation.

9. Step 18-20: Inserting Drawers

   Carefully slide the assembled drawers into their respective positions within the main frame, engaging the runners.

10. Step 21-22: Drawer Handle Installation

    Attach the drawer handles to the front of each drawer using the provided screws.

11. Step 23-39: Wall Mounting and Final Checks

    The final steps involve securing the furniture to the wall using the anti-tip hardware for safety and performing final checks on drawer operation.

Crucial Safety: Wall Mounting

This step is essential to prevent furniture tip-over. Follow these guidelines:

1. Wall Type Identification

   The provided screws and plugs are suitable for most solid (A) and hollow (B) walls. For solid wood (C), use screws without plugs. If uncertain, seek professional advice.

2. Drilling and Anchoring

   Mark the wall for drilling holes, ensuring alignment with the anti-tip bracket. Use the appropriate drill bit (Ø 5/16" or Ø 1/8") based on the wall type and hardware. For solid walls, insert screws directly or use wall plugs. For hollow walls, insert the provided wall plugs into the drilled holes.

3. Securing the Bracket

   Attach the anti-tip bracket to the wall using the provided screws. Ensure it is firmly fixed.

4. Connecting Furniture to Wall

   Attach the other end of the anti-tip hardware (strap or bracket) to the furniture, typically at the top rear. Connect this to the wall-mounted bracket, ensuring the furniture is pulled securely against the wall and cannot tip forward.

Drawer Interlock System: Ensure the drawer interlock system functions correctly, preventing more than one drawer from being opened simultaneously, which enhances stability.