LAIVA Bookcase

Important Safety Information

WARNING! Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instructions carefully.

Parts List

20x Wooden Dowels (Part #101221)
4x Cam Lock Screws (Part #106989)
4x Cam Locks (Part #109041)
24x Wooden Dowels (Part #100823)
1x Screw (Part #100001)
2x Cam Lock Screws (Part #118331)
4x Cam Locks (Part #118224)
2x Shelf Supports (Part #101339)
2x Screws (Part #100001)
4x Washers (Part #100823)
2x Wall Attachment Brackets
1x Bag of Screws (for wall attachment, not included in furniture kit)

Assembly Steps

Step 1

Insert 4x Cam Lock Screws (Part #118331) into the designated holes on the two main side panels.

Step 2

Insert 4x Wooden Dowels (Part #101339) into the upper holes on the inside of the side panels. Insert 4x Cam Lock Screws (Part #118331) into the lower holes on the inside of the side panels.

Step 3

Insert 4x Cam Locks (Part #118224) into the large holes on the ends of the shelves. Ensure the arrow on the cam lock faces the edge of the shelf.

Step 4

Attach the shelves to the side panels. Align the cam lock screws on the side panels with the cam locks on the shelves. Insert 8x Wooden Dowels (Part #101339) into the remaining holes on the side panels.

Step 5

Attach the horizontal support pieces for the back panel to the rear of the unit using 2x Screws (Part #100001) and 4x Washers (Part #100823).

Step 6

Slide the shelves into their positions between the side panels.

Step 7

Secure the shelves. From the outside of the side panels, insert 2x Screws (Part #1000214) into each shelf. From the inside of the shelves, insert 10x Cam Locks (Part #109041) into the corresponding holes and tighten them to secure the shelves.

Step 8

Place the two back panels onto the rear of the assembled frame.

Step 9

Secure the back panels. Hammer 4x nails into the top edge of the back panels, approximately 5mm (1/4 inch) from the edge. Hammer another 4x nails into the bottom edge of the back panels, approximately 5mm (1/4 inch) from the edge.

Step 10

Complete the frame assembly. Hammer 11x nails into the top edge of the back panels and 11x nails into the bottom edge of the back panels to fully secure them.

Step 11

Attach the wall attachment brackets. Use 2x Screws (Part #106989) to attach the brackets to the top rear of the bookcase. Then, use appropriate screws and plugs (not included) to securely fasten the bookcase to the wall. Ensure the unit is stable and upright.

Final Check

The assembled bookcase should be stable. Ensure it is securely attached to the wall to prevent tipping.

Maximum load per shelf: 15 kg (33 lb).

	IKEA GERSBY Bookcase Assembly Instructions Comprehensive assembly guide for the IKEA GERSBY bookcase, detailing all steps, parts, and crucial safety information regarding wall attachment.
	TONSTAD Bookcase Assembly and Safety Guide This document provides assembly instructions and critical safety information for the IKEA TONSTAD bookcase, emphasizing the importance of securing the furniture to the wall to prevent tip-over injuries.
	IDANÄS Bookcase Assembly Instructions Detailed assembly instructions for the IKEA IDANÄS bookcase, including safety warnings and part identification. Ensure proper wall mounting to prevent tip-over injuries.
	HEMNES Bookcase Assembly Instructions \| IKEA Detailed assembly instructions for the IKEA HEMNES bookcase, including safety warnings, parts list, and step-by-step guidance for safe and proper assembly.
	RÅGRUND Shelving Unit - Assembly Instructions and Safety Warnings Comprehensive assembly guide and critical safety information for the IKEA RÅGRUND shelving unit. Includes instructions on installing the anti-tip device to prevent furniture tipover accidents.
	ENHET Wall Cabinet Assembly Instructions Comprehensive assembly guide for the IKEA ENHET wall cabinet, detailing parts, tools, safety warnings, and step-by-step instructions for building and mounting the unit.
	IKEA KALLAX Shelving Unit Assembly Instructions Detailed assembly instructions for the IKEA KALLAX shelving unit. Includes safety warnings regarding tip-over hazards, a comprehensive parts list, and step-by-step guidance for building and securely mounting the unit to the wall.
	PLATSA Furniture Assembly Instructions Comprehensive guide for assembling the IKEA PLATSA modular furniture system, including safety warnings, parts list, and step-by-step assembly instructions.