Assembly Instructions
LIVING SPACES
LUCA TWIN-TWIN BUNK BED
ITEM NO: Y2103W-340/341/342, Y2103B-340/341/342, Y2103G-340/341/342
SKU: 314663/314664/314665, 314575/314576/314577, 314619/314620/314621
Estimated Assembly Time: 230 minutes
Required Tools: Screwdriver (not included), Allen key (included)
IMPORTANT SAFETY WARNINGS
Please take time to read all instructions and warnings before beginning assembly!
Our Bunk Beds have been tested by an Independent Laboratory and are certified to be in compliance with ASTM F-1427, “Standard Consumer Safety Specification for Bunk Beds” and U.S. Government specifications 16 Code of Federal Regulations, parts 1213 and 1513.
- Follow the information on the warnings attached to the upper bunk end structure and on the carton. Do not remove this label.
- Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.
- Top surface of mattress must be at least five inches (127mm) below the upper edge of top guard rails.
- Do not allow children less than six years of age to use the upper bunk.
- Periodically, check and ensure that the guardrail, ladder and other components are in their proper position, free from damage and that all connectors are tight.
- Do not allow horseplay on or under the bed and prohibit jumping on the bed and ladder.
- Prohibit more than one person on upper bunk.
- Always use the ladder or Stairway Chest for entering and leaving the upper bunk.
- Do not use substitute parts. Contact Living Spaces for replacement parts.
- Use of a night-light may provide added safety precautions for a child using the upper Bunk.
- If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk beds without two full-length guardrails.)
- Always use guardrails on both long sides of the upper bunk.
- The use of water or sleep flotation mattress is expressly prohibited.
- Keep these instructions for future reference.
STRANGULATION HAZARD
Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for example, but not limited to hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
- Use only mattress which is 75" long and 37.5- 38.5" wide on upper bunk, lower bunk of Twin bed.
- Ensure thickness of mattress does not exceed 6" and mattress is at least 5" below upper edge of guardrails.
- Ensure thickness of mattress does not exceed 6" for lower bunk.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be requested from Living Spaces, usually at a cost.
KEEP ALL INSTRUCTIONS INCLUDED WITH YOUR BEDROOM COMPONENTS FOR FUTURE REFERENCE.
Assembly Options
Always use the ladder or Stairway Chest for entering and leaving the upper bunk. You will buy ladder/Stairway as options.
Option 1: Ladder
A diagram shows the bunk bed with a ladder attached to the side.
Option 2: Stairway Chest
A diagram shows the bunk bed with a stairway chest attached to the side.
Please place Stairway Chest is next to Bunkbed Side and wall.
Parts List
BOX 1-TW /TW + TW /FL UPPER ENDS/SLATS BUNK BED
| PART | SKU# | IMAGE | DESCRIPTION | QTY |
|---|---|---|---|---|
| A | 1987TT-A-W: (White) 1987TT-A-B: (Blue) 1987TT-A-G: (Grey) |
[Upper Ends] |
Upper Ends | 2 |
| J | 1987TT-J | [Slats] |
Slats | 1 |
BOX 2: TW /TW LOWER ENDS/SLATS BUNK BED
| PART | SKU# | IMAGE | DESCRIPTION | QTY |
|---|---|---|---|---|
| B | 1987TT-B-W:(White) 1987TT-B-B:(Blue) 1987TT-B-G:(Grey) |
[Lower Ends] |
Lower Ends | 2 |
| J | 1987TT-J | [Slats] |
Slats | 1 |
BOX 3- TW /TW SIDE/GUARD RAILS BUNK BED
| PART | SKU# | IMAGE | DESCRIPTION | QTY |
|---|---|---|---|---|
| C | 1987TT-C-W: (White) 1987TT-C-B: (Blue) 1987TT-C-G: (Grey) |
[Upper Rails] |
Upper Rails | 2 |
| D | 1987TT-D-W: (White) 1987TT-D-B: (Blue) 1987TT-D-G: (Grey) |
[Guard rails] |
Guard rails | 4 |
| E | 1987TT-E-W: (White) 1987TT-E-B: (Blue) 1987TT-E-G: (Grey) |
[Guard rail supports] |
Guard rail supports | 2 |
| F | 1987TT-F-W: (White) 1987TT-F-B: (Blue) 1987TT-F-G: (Grey) |
[Lower rails] |
Lower rails | 2 |
Hardware List of Twin-Twin Bunk Bed
| Part | SKU# | IMAGE | DESCRIPTION | QTY |
|---|---|---|---|---|
| 1 | 1987TT-1(16) | [Bolt and nut] |
Bolt and nut M8*90mm | 16 |
| 2 | 1987TT-2(6) | [Bolts] |
Bolts M8*35mm | 6 |
| 3 | 1987TT-3(8) | [Screws] |
Screws Ø6.5*83mm | 8 |
| 4 | 1987TT-4(16) | [Dowel] |
Dowel Ø8*40mm | 16 |
| 5 | 1987TT-5(28) | [Screws] |
Screws 8#*30mm | 28 |
| 6 | 1987TT-6(4) | [Metal dowel] |
Metal dowel Ø10*100mm | 4 |
| 7 | 1987TT-7(1) | [Allen key] |
Allen key 60*22*4mm | 1 |
Note: Screwdriver will be prepared by yourself. THE HARDWARE IS LOCATED IN THE PACKING ITEM.
NOTE: MUST TIGHTEN SCREWS PERIODICALLY. WITH USE SCREW MAY BECOME LOOSE. CHECK TIGHTNESS OF ALL SCREWS EVERY 6-8 WEEKS.
CLEANING INSTRUCTIONS: After assembly, clean and polish the completed parts if necessary with soft cloth and industrial recognized furniture polish.
Assembly Steps
STEP 1:
Assembly Rail (C): Please locate two rails (C) to Ends (A) by Dowel (4) firstly, and then fasten gradually by Bolt+nut (1) BUT NO TIGHTEN.
Assembly Guard Rail (D): Please locate Guard rails (D) to Ends (A) by Dowel (4) firstly, and then fasten gradually by Bolt (3).
Pay attention to rail orientation.
A diagram shows the initial assembly of the bunk bed frame, indicating the placement of parts C and D onto part A using dowels (4) and bolts/nuts (1) and bolts (3). Quantities indicated: 4=12Pcs, 1=8Pcs, 3=8Pcs.
STEP 2:
Assemble the Guard Rail Supports (E) to Upper bed frame by Bolt (2).
A diagram shows the attachment of guard rail supports (E) to the upper bed frame using bolts (2). Quantities indicated: 2=6Pcs.
STEP 3:
Please fasten slats (J) by screw (5) into corresponding holes.
A diagram shows the attachment of slats (J) to the bed frame using screws (5). Quantities indicated: 5=14Pcs.
STEP 4:
Insert dowel (4) to Ends (B) firstly, then the Rails (F) are fastened by Bolt+nut (1).
Pay attention to rail orientation.
A diagram shows the assembly of the lower bunk, attaching rails (F) to ends (B) using dowels (4) and bolts/nuts (1). Quantities indicated: 4=4Pcs, 1=8Pcs.
STEP 5:
Please fasten slats (J) by screw (5) into corresponding holes.
A diagram shows the attachment of slats (J) to the lower bed frame using screws (5). Quantities indicated: 5=14Pcs.
STEP 6:
Assemble the upper bunk to lower bunk by Metal dowel (6).
A diagram shows the two bunks being joined together using metal dowels (6). Quantities indicated: 6=4Pcs.
Combining with Ladder (Option 1)
Attaching the ladder to Guard rail by Screw (this hardware is placed in ladder box)
A diagram shows the ladder being attached to the bunk bed.
Combining with Stairway Chest (option 2)
Please attach the Stairway Chest to Bunk bed by metal bracket and screw (are placed in Stairway box).
A diagram shows the stairway chest being attached to the bunk bed.
Final Assembly Check
That's it! You've finished assembling your item. Thank you!
