MSI Optix MAG321CURV (3DA2) and MAG322CQRV (3DA4) LCD Monitors

Table of Contents

• Copyright and Trademarks
• Revision
• Technical Support
• Safety Precautions
• CE Compliance
• FCC-B Radio Frequency Interference Statement
• WEEE Declaration
• Chemical Substance Information
• Japan JIS C 0950 Material Declaration
• 1. User's Guide
• Package Contents
• Monitor Stand Installation
• Monitor Adjustment
• Monitor Overview
• Connecting the Monitor to a PC
• 2. OSD Settings
• Navi Key
• Navi Key OSD Settings
• Appendix
• Specifications
• Preset Display Modes
• Troubleshooting

Copyright and Trademarks

This document is copyrighted by Micro-Star Int'l Co., Ltd. and is protected by copyright. MSI logo is a registered trademark of Micro-Star Int'l Co., Ltd. All trademarks mentioned herein belong to their respective owners. While every effort has been made to ensure the accuracy of the information in this document, no guarantee is provided regarding its accuracy. MSI products are continuously improved, and MSI reserves the right to make changes without prior notice.

Revision

Revision: V1.0
Date: 2019/06

Technical Support

If you encounter problems with your product that cannot be resolved using the user manual, please contact your place of purchase or the nearest distributor. For more information, please visit https://www.msi.com/support/.

Safety Precautions

• Please read the safety precautions carefully.
• Comply with all warnings and cautions affixed to the equipment or in the user manual.
• Service should only be performed by qualified personnel.
• Keep the user guide that comes with the package for future reference.
• To prevent fire or electric shock, do not expose this equipment to humidity or high temperatures.
• When setting up the equipment, place it on a flat surface.
• Before connecting the equipment to the power outlet, ensure that the voltage is within the safety range and that it is correctly adjusted for the 100-240V voltage range. Do not disable the protective earth pin of the plug. This equipment must be connected to a grounded power outlet.
• If you will not be using the equipment for an extended period, unplug the power cord or turn off the wall switch to prevent unnecessary power consumption.
• The ventilation openings on this equipment are used to protect the equipment from airflow and overheating. Do not block the ventilation openings.
• Do not expose the equipment to an environment with temperatures exceeding 60°C or below -20°C. This may damage the equipment. Note: The maximum operating temperature is approximately 40°C.
• When cleaning the equipment, always unplug the power cord. Use a soft cloth for cleaning; avoid using industrial chemicals. Pouring liquid into openings may cause damage or electric shock.
• Ensure the power cord is routed so it is not stepped on or pinched by objects.
• Keep strong magnetic or electrical objects away from the equipment.
• Request service from a qualified technician if:
• The power cord or plug is damaged.
• Liquid has entered the equipment.
• The equipment has been exposed to moisture.
• The equipment does not operate normally or does not start up according to the user manual.
• The equipment has been dropped and damaged.
• The equipment shows visible damage.

Green Product Features

• Reduced energy consumption during use and standby.
• Limited use of substances harmful to the environment and health.
• Easy disassembly and recycling.
• Encourages recycling to conserve natural resources.
• Reduced solid waste through recycling policies.

Environmental Policy

This equipment is designed for proper use and recycling of components. Do not dispose of the product as general waste at the end of its lifespan. Please contact your local authorities for information on recycling and disposal of end-of-life products. Visit the MSI website to find a local retailer for recycling information. For information on proper disposal, collection, recycling, and disassembly of MSI products, please contact gpcontdev@msi.com.

Warning! Excessive screen use may affect vision.

Recommendation:

• Take a 10-minute break for every 30 minutes of screen time.
• Children under 2 years old should not use the screen. For children over 2 years old, limit screen time to less than 1 hour per day.

Note: The power cord supplied with this product is for the monitor only and should not be used with other products.

CE Compliance

This equipment complies with the Council Directive on the approximation of the laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low Voltage Directive (2014/35/EU), ErP Directive (2009/125/EC), and RoHS Directive (2011/65/EU). The product has been tested and confirmed to comply with the harmonized standards published in the Official Journal of the European Union.

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. To determine if this equipment causes radio or television reception interference, turn the equipment off and on. If interference occurs, try the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Note 1: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note 2: Shielded interface cables and AC power cord must be used to comply with the emission limits.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this equipment may not cause interference, and (2) this equipment must accept any interference received, including interference that may cause undesired operation.

WEEE Declaration

In accordance with the European Union (EU) Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), products marked as "Electrical and Electronic Equipment" cannot be disposed of as general waste. Manufacturers are obligated to collect such products at the end of their service life.

Chemical Substance Information

This product complies with chemical substance regulations such as EU REACH Regulation (European Parliament and Council Regulation EC No. 1907/2006). MSI provides information on chemical substances in products at https://www.msi.com/html/popup/csr/evmtprtt_pcm.html.

Japan JIS C 0950 Material Declaration

The Japanese regulatory requirement stipulated in the JIS C 0950 standard mandates manufacturers to provide a declaration for specific categories of electronic products sold after July 1, 2006. For more information, please visit:

• https://www.msi.com/html/popup/csr/cemm_jp.html
• https://tw.msi.com/html/popup/csr_tw/cemm_jp.html

1. User's Guide

This chapter explains the hardware setup procedure. When handling the equipment, pay close attention to static electricity precautions and use a grounded wrist strap.

Note: Illustrations are for reference only. The appearance of your monitor may differ.

Caution: Do not use pointed objects on the monitor.

Package Contents

1. Monitor
2. Stand
3. Stand Base with Screws
4. Power Adapter & Power Cord
5. HDMI Cable
6. DisplayPort Cable
7. USB Upstream Cable (to enable monitor USB ports)
8. Quick Start Guide
9. Warranty Card

* If any item is damaged or missing, please contact your retailer or local distributor.

* Package contents may vary by country.

Monitor Stand Installation

1. Place the stand onto the monitor.
2. Secure the stand with screws.
3. Connect the base to the stand and securely fasten it to the base with screws.

Caution: Place the monitor on a soft, protected surface to avoid scratching the display panel.

[Illustration showing stand assembly steps]

Monitor Adjustment

This monitor is designed with tilt and lift adjustment functions to maximize viewing comfort.

Caution: Do not touch the display panel when adjusting the monitor.

[Illustration showing monitor tilt adjustment range of -5° to 20° and a height adjustment of 130mm]

Monitor Overview

[Illustration of the monitor with numbered connection ports]

1. Power Button
2. Navi Key
3. Power Jack
4. HDMI Port
5. DisplayPort
6. USB Type-C Port (For Optix MAG321CURV)

This port supports DisplayPort Alternate (DP Alt) mode and power transfer up to 5V/3A (15W). It supports video signal transmission only and does not support data transmission.

7. USB Type B Upstream Port

Use the USB upstream cable included in the package to connect the PC and monitor. Once this cable is connected, the monitor's USB Type-A downstream ports will be enabled.

[Illustration of USB upstream cable connection]

8. Headphone Jack
9. USB Type-A Downstream Port
10. Kensington Lock

Connecting the Monitor to a PC

1. Turn off the computer.
2. Connect the HDMI/DisplayPort cable from the monitor to the computer.
3. Attach the monitor's power adapter/power cord. (Figure A)
4. Connect the power adapter to the monitor's power jack. (Figure B)
5. Plug the power cord into the power outlet. (Figure C)
6. Turn on the monitor's power. (Figure D)
7. Select the input source in the OSD menu and turn on the computer.

[Illustration showing connection steps A, B, C, D]

2. OSD Settings

This chapter provides important information regarding OSD settings.

Important: All information is subject to change without notice.

Navi Key

The monitor is equipped with a multi-directional Navi Key for navigating the On-Screen Display (OSD) menu.

[Illustration of the monitor's rear with the Navi Key highlighted and a close-up of the Navi Key controls]

Navi Key Default Settings

Optix MAG321CURV OSD Example:

[Screenshot of MAG321CURV OSD menu]

Optix MAG322CQRV OSD Example:

[Screenshot of MAG322CQRV OSD menu]

Navi Key Hotkey Options

Navi Key OSD Settings

You can customize your own Navi Key hotkeys by accessing the OSD menu.

Optix MAG321CURV OSD Navigation:

Pressing the center button of the Navi Key displays the OSD main menu. Use the up, down, left, and right buttons to adjust the desired function menu according to your preferences.

[Screenshot of MAG321CURV OSD menu with navigation]

Optix MAG322CQRV OSD Navigation:

[Screenshot of MAG322CQRV OSD menu with navigation]

OSD Menu Details

GAMING (ゲーミング)

Alarm Clock (アラームクロック)

Screen Assistance (スクリーンアシスタント)

Adaptive Sync (Optix MAG322CQRVの場合)

Professional (プロフェッショナル)

Image (イメージ)

Input Source (入力源)

PIP/PBP

Navi Key (ナビキー)

Setting (設定)

Appendix

Important: All information is subject to change without notice.

Specifications

* Based on CIE1976 test standards.

Preset Display Modes

[Table listing resolutions and supported refresh rates via HDMI, DP, and Type-C for both monitor models]

Troubleshooting

• Power LED is off:
• Press the monitor's power button again.
• Check if the monitor's power cord is properly connected.
• No image is displayed:
• Check if the computer's graphics card is installed correctly.
• Ensure the computer and monitor are connected to the power outlet and powered on.
• Check if the monitor's signal cable is properly connected.
• The computer may be in standby mode. Press any key to wake the monitor.
• Screen image size is incorrect or not centered:
• To set the computer to a suitable display setting, refer to "Preset Display Modes".
• Plug and Play does not function:
• Check if the monitor's power cord is properly connected.
• Check if the monitor's signal cable is properly connected.
• Ensure the computer and graphics card are Plug and Play compatible.
• Icons, fonts, or screen are blurry, fuzzy, or have color issues:
• Do not use video extension cables.
• Adjust brightness and contrast.
• Adjust RGB colors or color temperature.
• Check if the monitor's signal cable is properly connected.
• Check if the pins on the signal cable connector are bent.
• Monitor starts flickering or displaying waves:
• Change the refresh rate to match the monitor's capabilities.
• Update the graphics card driver.
• Do not place the monitor near electrical equipment that may cause electromagnetic interference (EMI).

Chemical Substance Table

[Table showing presence of substances like Pb, Hg, Cd, Cr6+, PBBs, PBDEs in different parts of the monitor]

* PCBA is composed of bare printed circuit boards, including soldered components, resistors, capacitors, arrays, connectors, chips, etc.

Note 1: "O" indicates that the content of the calculated substance does not exceed the reference content.

Note 2: "Exempted" items correspond to specific chemical substances that have been exempted according to the JIS C 0950 standard.