MSI Optix G24C6 / G24C6P / G27C6 / G27C6P LCD Monitor
This document provides instructions for setting up and using your MSI Optix LCD monitor.
Getting Started
This section covers hardware configuration. Handle devices with care and use an anti-static wrist strap to prevent static discharge.
Box Contents
| Item | Details |
|---|---|
| Monitor | Optix G24C6 / Optix G24C6P / Optix G27C6 / Optix G27C6P |
| Documentation | Quick Start Guide, Warranty Card, Registration Card |
| Accessories | Stand with screws, Stand base with screws, Power cable, Power adapter |
| Cable | HDMI Cable (Optional), DisplayPort Cable (Optional) |
Important: If any item is damaged or missing, contact your retailer or local distributor. Package contents may vary by country.
Monitor Stand Installation
For Optix G24C6 / Optix G27C6
- Keep the monitor in its protective foam packaging. Align the stand bracket with the slot on the monitor.
- Secure the stand bracket by screwing in the screws.
- Attach the stand base to the stand and tighten the base screw.
- When attaching the stand cover, align the latches.
- Before placing the monitor upright, ensure the stand is properly installed.
Diagram Description: The installation involves attaching a bracket (1) to the monitor, then attaching the stand (2) to the bracket using screws (3), and finally securing the base. A cover (4) is also shown being attached.
For Optix G24C6P / Optix G27C6P
- Keep the monitor in its protective foam packaging. Align the stand bracket with the slot on the monitor.
- Secure the stand bracket by screwing in the screws.
- Attach the stand base to the stand and tighten the base screw.
- Before placing the monitor upright, ensure the stand is properly installed.
Important: Place the monitor on a soft, protected surface to prevent scratching the display panel. Do not touch the panel with sharp objects. The stand installation slot can also be used for wall mounting. Consult your retailer for a suitable wall mount kit.
Diagram Description: Similar to the previous installation, this shows attaching a bracket (1) to the monitor, then the stand (2) with screws (3).
Monitor Adjustment
This monitor offers adjustment options for maximum viewing comfort.
Important: Do not touch the display panel when adjusting the monitor.
- Optix G24C6 / Optix G27C6: The monitor can be tilted from -5° to 20°.
- Optix G24C6P / Optix G27C6P: The monitor can be tilted from -5° to 20° and adjusted vertically by up to 130mm.
Monitor Description
Optix G24C6 / Optix G27C6
Diagram Description: Front view shows the monitor screen (1). Rear view shows the stand connection (2), Kensington lock (3), and ports (4, 5, 6, 7).
Optix G24C6P / Optix G27C6P
Diagram Description: Front view shows the monitor screen (1). Rear view shows the stand connection (2), Kensington lock (3), and ports (4, 5, 6, 7).
Port Identification
- 1. Power Button: Turns the monitor on/off.
- 2. Navi Key: A multi-directional joystick for OSD navigation.
- 3. Kensington Lock: For securing the monitor.
- 4. Power Input: Connects the power adapter.
- 5. HDMI Port: High-Definition Multimedia Interface port.
- 6. DisplayPort: Connects to compatible devices.
- 7. Headphone Jack: For audio output.
Connecting Monitor to PC
- Turn off the computer.
- Connect the monitor's video cable to the computer.
- Connect the monitor's power adapter and the AC power cord (Diagram A).
- Connect the power adapter to the monitor's power input (Diagram B).
- Connect the AC power cord to the electrical outlet (Diagram C).
- Turn on the monitor (Diagram D).
- After powering on the computer, the monitor will automatically detect the signal source.
Diagram Description: Shows connecting the power adapter (A) to the monitor (B) and then to the wall socket (C). The power button (D) is indicated.
OSD Settings
This chapter provides basic information about OSD settings.
Important: Information is subject to change without prior notice.
Navi Key (Joystick)
The monitor is equipped with a Navi Key, a directional controller that simplifies navigation within the OSD (On-Screen Display) menu.
- Up / Down / Left / Right: Used to select menus and function items, adjust function values, and open/close function menus.
- Pressing the Button (OK): Opens the OSD menu, enters submenus, and confirms selections or settings.
Quick Key
- Moving the Navi Key up, down, left, or right when the OSD menu is not displayed allows access to Game Mode, Screen Assistance, Alarm Clock, and Input Source functions.
- Users can assign custom shortcuts to the quick keys for accessing various function menus.
OSD Menus
Gaming (Game Mode)
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
|---|---|---|---|
| Game Mode (Režim Hra) | User (Uživatel) | Users can adjust all items. | |
| FPS | Use the Up/Down buttons to select and preview mode effects. | ||
| Racing (Závody) | Press OK to confirm and apply your mode type. | ||
| RTS | |||
| RPG | |||
| Night Vision (Noční vidění) | OFF (Vyp.) | This function optimizes backlight brightness and is recommended for FPS games. | |
| Normal (Normální) | |||
| Strong (Silné) | |||
| Strongest (Nejsilnější) | |||
| A.I. (Umělá inteligence) | |||
| Response Time (Doba odezvy) | Normal (Normální) | Users can adjust response time in any mode. | |
| Fast (Rychle) | When Motion Blur Reduction is activated, the Response Time item will be grayed out. | ||
| Fastest (Nejrychleji) | |||
| MPRT | OFF (VYP.) | When MPRT is activated, brightness cannot be adjusted and will be displayed in gray. MPRT and HDCR cannot be activated simultaneously. | |
| ON (ZAP.) | |||
| Refresh Rate (Obnovovací kmitočet) | Location (Místo) | Upper Left | Users can adjust the refresh rate in any mode. |
| Top Right | The default refresh rate location is Top Left. Location can be adjusted in the OSD menu. Press OK to confirm and apply your custom refresh rate location. | ||
| Bottom Left | |||
| Bottom Right | This monitor tracks and operates at the refresh rate set in the operating system. | ||
| Alarm Clock (Budík) | Location (Umístění) | Upper Left | Users can set the alarm clock in any mode. |
| Top Right | After setting the time, activate the timer by pressing OK. | ||
| Bottom Left | The default alarm clock location is Top Left. Users can choose their custom location. | ||
| Bottom Right | |||
| OFF (Vyp.) | |||
| 15:00 | 00:01~99:59 | ||
| 30:00 | |||
| 45:00 | |||
| 60:00 | |||
| Screen Assistance (Asistent plátna) | None (Žádné) | Users can adjust screen aids in any mode. The default screen aid setting is None. |
Professional (Profesionální)
| 1st Level Menu | 2nd Level Menu | Description |
|---|---|---|
| Pro Mode (Režim Pro) | User (Uživatel) | The default mode is User. Users can adjust all items. |
| Reader (Čtení) | Use the Up/Down buttons to select and preview mode effects. | |
| Cinema (Kino) | Press OK to confirm and apply your mode type. | |
| Designer (Návrhář) | ||
| Eye Saver (Ochrana zraku) | OFF (VYP.) | Eye Saver protects your eyes from blue light. When activated, it adjusts the screen's color temperature to yellow. Users can adjust Eye Saver in any mode. |
| ON (ZAP.) | When Pro Mode is set to Reader, Eye Saver must be activated. | |
| HDCR | OFF (VYP.) | Users can adjust HDCR in any mode. HDCR enhances image quality by increasing contrast. |
| ON (ZAP.) | When HDCR is ON, the brightness setting will be grayed out. HDCR and Motion Blur Reduction cannot be activated simultaneously. | |
| Anti Motion Blur (Potlačení rozmazání) | OFF (VYP.) | When Motion Blur is activated, HDCR cannot be activated and brightness will be grayed out. When Motion Blur Reduction is activated, the Response Time item will be grayed out. |
| ON (ZAP.) | When FreeSync Premium is activated, Motion Blur must be turned off. | |
| Image Enhancement (Vylepšení obrazu) | OFF (Vyp.) | Image enhancement improves image edges for optimal sharpness. Users can adjust image enhancement in any mode. |
| Weak (Slabý) | ||
| Medium (Střední) | ||
| Strong (Silné) | ||
| Strongest (Nejsilnější) |
Image (Obraz)
| 1st Level Menu | 2nd/3rd Level Menu | Description | |
|---|---|---|---|
| Brightness (Jas) | 0-100 | Users can adjust brightness in User, RTS, RPG, and Reader modes. When Motion Blur Reduction or HDCR is activated, the brightness setting will be grayed out. | |
| Contrast (Kontrast) | 0-100 | Users can adjust contrast in any mode. | |
| Sharpness (Ostrost) | 0-5 | Users can adjust sharpness in any mode. Sharpness improves image clarity and detail. | |
| Color Temperature (Teplota barev) | Cool (Studená) | The default color temperature setting is Normal. | |
| Normal (Normální) | Use the Up/Down buttons to select and preview mode effects. | ||
| Warm (Teplá) | Press OK to confirm and apply your mode type. | ||
| Customization (Přizpůsobení) | C (0-100) | Users can adjust color temperature in customization mode. | |
| Z (0-100) | |||
| M (0-100) | |||
| Screen Size (Velikost obrazu) | Auto (Automaticky) | Users can adjust Screen Size in any mode, at any resolution, and at any screen refresh rate. The default setting is Auto. | |
| 4:3 | |||
| 16:9 |
Input Source (Vstupní zdroj)
| 1st Level Menu | 2nd Level Menu | Description |
|---|---|---|
| HDMI1 | Users can adjust the input source in any mode. | |
| HDMI2 | ||
| DP | ||
| Auto Scan (Automatické hledání) | ON (ZAP.) | Users can select the input source using the navigation button in the following situations: |
| OFF (VYP.) |
|
Navi Key (Navigační tlačítko)
| 1st Level Menu | 2nd Level Menu | Description |
|---|---|---|
| Up (Nahoru) / Down (dolů) / Left (vlevo) / Right (vpravo) | OFF (Vyp.) | The default setting for the Up button is Game Mode. |
| Brightness (Jas) | The default setting for the Down button is Screen Assistance. | |
| Game Mode (Režim Hra) | The default setting for the Left button is Alarm Clock. | |
| Screen Assistance (Asistent plátna) | The default setting for the Right button is Input Source. | |
| Alarm Clock (Budík) | All navigation controller items can be adjusted in the OSD Menu. | |
| Input Source (Vstupní zdroj) | ||
| Refresh Rate (Obnovovací kmitočet) | ||
| Information on Screen (Informace na displeji) |
Setting (Nastavení)
| 1st Level Menu | 2nd Level Menu | Description |
|---|---|---|
| Language (Jazyk) | Traditional Chinese | The default factory language setting is English. |
| English | Users must press the OK button to confirm and apply the language setting. | |
| Français | The language is an independent setting. User's custom language setting will override the default factory setting. When users enable reset, the language setting will not change. | |
| Deutsch | ||
| Italiano | ||
| Español | ||
| Korean | ||
| Japanese | ||
| Russian | ||
| Portuguese | ||
| Simplified Chinese | ||
| Thai | ||
| Bahasa Indonesia | ||
| Hindi | ||
| Turkish | ||
| (Další jazyky se připravují) | (Other languages are being prepared) | |
| Transparency (Průsvitnost) | 0~5 | Users can adjust transparency in any mode. |
| OSD Time Out (Časový interval OSD) | 5 ~ 30 s | Users can adjust the OSD Time Out in any mode. |
| Power Button (Vypínač) | OFF (Vyp.) | When set to OFF, the monitor can be turned off by pressing the power button. |
| Standby (Pohotovostní režim) | When set to "Standby", the panel and backlight can be turned off by pressing the power button. | |
| Information on Screen (Informace na obrazovce) | OFF (VYP.) | Monitor status information will be displayed on the right side of the screen. |
| ON (ZAP.) | Users can activate or deactivate the Information on Screen function. The default is OFF. | |
| Reset (Vynulovat) | YES (ANO) | Users can restore default OSD settings in any mode. |
| NO (NE) |
Technical Specifications
| Model | Optix G24C6 (3BA0) | Optix G24C6P (3BA0) | Optix G27C6 (3CA9) | Optix G27C6P (3CA9) |
|---|---|---|---|---|
| Size | 24-inch | 24-inch | 27-inch | 27-inch |
| Curvature | 1500R | 1500R | 1500R | 1500R |
| Panel Type | VA | VA | VA | VA |
| Resolution | 1920 x 1080 at 144Hz | 1920 x 1080 at 144Hz | 1920 x 1080 at 165Hz | 1920 x 1080 at 165Hz |
| Aspect Ratio | 16:9 | 16:9 | 16:9 | 16:9 |
| Brightness (nits) | 250 (Typ.) | 250 (Typ.) | 250 (Typ.) | 250 (Typ.) |
| Contrast Ratio | 3000:1 | 3000:1 | 3000:1 | 3000:1 |
| Refresh Rate | 144Hz | 144Hz | 165Hz | 165Hz |
| Response Time | 1 ms (MPRT) | 1 ms (MPRT) | 1 ms (MPRT) | 1 ms (MPRT) |
| Input Interface | HDMI x 2, DP x 1 | HDMI x 2, DP x 1 | HDMI x 2, DP x 1 | HDMI x 2, DP x 1 |
| Output Interface | Headphone connector x 1 | Headphone connector x 1 | Headphone connector x 1 | Headphone connector x 1 |
| Viewing Angles | 178°(H), 178°(V) | 178°(H), 178°(V) | 178°(H), 178°(V) | 178°(H), 178°(V) |
| DCI-P3*/sRGB | 92% / 115.5% | 92% / 115.5% | 90% / 113% | 90% / 113% |
| Surface Treatment | Anti-glare | Anti-glare | Anti-glare | Anti-glare |
| Display Colors | 16.7 Million (8 bits) | 16.7 Million (8 bits) | 16.7 Million (8 bits) | 16.7 Million (8 bits) |
| Power Type | External Power Adapter | External Power Adapter | External Power Adapter | External Power Adapter |
| Adapter Model | ADPC2045 | ADPC2045 | ADPC2045 | ADPC2045 |
| Power Input | 100~240 Vac, 50~60 Hz, 1.5 A | 100~240 Vac, 50~60 Hz, 1.5 A | 100~240 Vac, 50~60 Hz, 1.5 A | 100~240 Vac, 50~60 Hz, 1.5 A |
| Power Output | 20V 2.25A | 20V 2.25A | 20V 2.25A | 20V 2.25A |
| Tilt Adjustment | -5° ~ 20° | -5° ~ 20° | -5° ~ 20° | -5° ~ 20° |
| Height Adjustment | No | No | 0 ~ 130mm | 0 ~ 130mm |
| Kensington Lock | Yes | Yes | Yes | Yes |
| Model | VESA Mount | Dimensions (W x H x D) | Weight | Environment |
|---|---|---|---|---|
| Operation | ||||
| Optix G24C6 (3BA0) | VESA Mount Details:
| 536.7 x 416.33 x 219.6 mm | 3.4 kg / 5 kg |
|
| Optix G24C6P (3BA0) | 536.7 x 538.3 x 231.2 mm | 4.5kg / 6.8kg | ||
| Optix G27C6 (3CA9) | 611.5 x 445.9 x 219.6 mm | 4.53 kg / 6.7 kg | ||
| Optix G27C6P (3CA9) | 611.5 x 567.1 x 266.52 mm | 5.7kg / 8.2kg | Storage
|
* Based on CIE1976 testing standards.
Preset Display Modes
| Standard | Resolution | Optix G24C6 (3BA0) / Optix G24C6P (3BA0) HDMI/DP | Optix G27C6 (3CA9) / Optix G27C6P (3CA9) HDMI/DP |
|---|---|---|---|
| VGA | 640x480 at 60Hz | V | V |
| 640x480 at 67Hz | V | V | |
| 640x480 at 72Hz | V | V | |
| 640x480 at 75Hz | V | V | |
| DOS Mode | 720x480 at 60Hz | V | V |
| 720x576 at 50Hz | V | V | |
| SVGA | 800x600 at 56Hz | V | V |
| 800x600 at 60Hz | V | V | |
| 800x600 at 72Hz | V | V | |
| 800x600 at 75Hz | V | V | |
| XGA | 1024x768 at 60Hz | V | V |
| 1024x768 at 70Hz | V | V | |
| 1024x768 at 75Hz | V | V | |
| SXGA | 1280x1024 at 60Hz | V | V |
| 1280x1024 at 75Hz | V | V | |
| WXGA+ | 1440x900 at 60Hz | V | V |
| WSXGA+ | 1680x1050 at 60Hz | V | V |
| Full HD | 1920x1080 at 60Hz | V | V |
| 1920x1080 at 120Hz | V | V | |
| 1920x1080 at 144Hz | V | V | |
| 1920x1080 at 165Hz | X | DP | |
| Video Resolution | 480P | V | V |
| 576P | V | V | |
| 720P | V | V | |
| 1080P | V | V | |
| 1080P at 120Hz | V | V |
Troubleshooting
- LED Power Indicator Not Lit: Press the monitor power button again. Ensure the monitor's AC power cord is properly connected.
- No Image: Check if the graphics card is installed correctly. Ensure the computer and monitor are plugged into working electrical outlets and are powered on. Verify the monitor's signal cable is properly connected. The computer might be in standby mode; activate the monitor by pressing any button.
- Image Size Incorrect or Not Centered: Refer to the preset display modes and use the computer's settings appropriate for the monitor.
- No Plug & Play Function: Ensure the monitor's AC power cord is properly connected. Verify the monitor's signal cable is properly connected. Check if the computer and graphics card are compatible with Plug & Play.
- Icons, Font, or Screen Unclear, Blurred, or Incorrect Colors: Do not use any extension video cables. Adjust brightness and contrast. Adjust RGB color or fine-tune color temperature. Ensure the monitor's signal cable is properly connected. Check for bent pins in the signal cable connector.
- Monitor Flickering or Displaying Waves: Change the refresh rate to match your monitor's capabilities. Update your graphics card drivers. Keep the monitor at a safe distance from electrical devices that may cause electromagnetic interference (EMI).
Safety Instructions
- Read and follow these safety instructions carefully.
- Adhere to all warnings and cautions on the device or in the user manual.
- Only qualified service technicians should perform repairs.
- Keep the user manual for future reference.
- To prevent fire or electric shock, keep this device away from moisture and high temperatures.
- Place the device on a stable, level surface before connecting it.
- Before plugging into an electrical outlet, check that the voltage is within the safe range and set correctly for 100~240 V. Do not disable the protective grounding pin on the plug. This device must be connected to a grounded electrical outlet.
- If the device will not be used for an extended period, always unplug the AC power cord or turn off the electrical outlet to conserve energy.
- The device's fan provides ventilation and prevents overheating. Do not cover the fan.
- Do not leave the device in environments with temperatures above 60°C or below -20°C, as this may cause damage.
- NOTE: The maximum operating temperature is around 40°C.
- Before cleaning, disconnect the AC power cord. Use a soft cloth for cleaning and avoid chemical cleaners. Never pour any liquid into openings, as this could damage the device or cause electric shock.
- Position the power cord so that it is not stepped on. Do not place anything on the power cord.
- Keep objects with strong magnetic or electric fields away from the device.
- If any of the following situations occur, have the device inspected by a service technician:
- The power cord or plug is damaged.
- Liquid has entered the device.
- The device has been exposed to moisture.
- The device is not functioning properly or as described in the user manual.
- The device has been dropped and damaged.
- The device shows obvious signs of damage.
- To prevent the monitor from tipping over, secure it to a desk, wall, or sturdy object with a bracket that prevents tipping and keeps it securely in place.
Important: Ensure the building's electrical system includes a 120/240 V, 20 A (maximum) circuit breaker.
Regulatory Information
CE Declaration of Conformity
This device complies with the requirements of the harmonization directives of the member states regarding electromagnetic compatibility (2014/30/EU), low voltage (2014/35/EU), ErP (2009/125/EC), and RoHS (2011/65/EU). Based on testing of this product, it has been found to comply with harmonized standards for IT equipment issued under European Union directives.
FCC Declaration for Class B Radio Frequency Interference
This device has been tested and verified to comply with the parameters for a Class B digital device under Part 15 of the FCC Rules. These limits are intended to provide reasonable protection against harmful interference in residential installations. The device generates, uses, and may emit radio frequency electromagnetic radiation, and if not installed and used according to the instructions, may cause harmful interference to radio and television broadcasting. However, there is no guarantee that interference will not occur in a particular installation. If radio or television reception is interfered with, which can be determined by turning the device off and on, users are advised to try to limit the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the device and the receiver.
- Connect the device to an outlet on a different circuit than the one the receiver is connected to.
- If necessary, consult the place of purchase or an experienced radio or television technician.
Note 1: Any changes or modifications to this device not expressly approved by the party responsible for compliance may void the user's authority to operate the device.
Note 2: To comply with emission limits, shielded interface cables and a power cord (if included) must be used.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device must not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
WEEE Information
According to the European Union Directive ("EU") on waste electrical and electronic equipment, Directive 2012/19/EU, "electrical and electronic equipment" products can no longer be disposed of as municipal waste, and manufacturers of covered electronic equipment will be required to take back such products after their service life.
Information on Chemical Substances
In accordance with regulations governing the use of chemical substances, such as EU REACH (Directive of the European Parliament and Council EC No. 1907/2006), MSI provides information on chemical substances used in its products on the website: https://storage-asset.msi.com/html/popup/csr/evmtprtt_pcm.html
Environmental Properties of the Product
- Reduced energy consumption during use and standby.
- Limited use of substances harmful to the environment and health.
- Easy disassembly and recycling.
- Limited use of natural resources through recycling support.
- Extended product lifespan through easy innovation.
- Limited generation of solid waste through collection of used products.
Ecological Principles
- This product is designed to allow for the reuse of components and recycling, and must not be disposed of as waste after its service life.
- Users must contact their local authorized waste collection point that handles the recycling and disposal of their end-of-life products.
- Further information on recycling can be obtained from your nearest distributor, which can be found on the MSI company website.
- Users can also contact us at gpcontdev@msi.com with requests for information regarding proper disposal, collection, recycling, and disassembly of MSI products.
Warning! Excessive screen viewing may cause eye damage.
Recommendations:
- Take a 10-minute break for every 30 minutes of screen viewing.
- Children under 2 years of age should not look at the screen. Children aged 2 and above should only view for limited periods, less than one hour per day.
Copyright and Trademark Notice
Copyright © Micro-Star Int'l Co., Ltd. All rights reserved. The MSI logo is a registered trademark of Micro-Star Int'l Co., Ltd. All other trademarks and names mentioned in this document are trademarks of their respective companies. We do not provide any express or implied warranty of accuracy or completeness. MSI reserves the right to change this document at any time without prior notice.
Technical Support
If you encounter a problem with your product that cannot be resolved according to the user manual, contact your place of purchase or local distributor. Alternatively, seek further assistance on the web at https://www.msi.com/support/
