Caséta Wireless In-Wall Dimmer Quick Start Guide

Getting Started

Contents Supplied

• In-wall dimmer (PD-6WCL)
• Claro® wallplate (CW-1)
• Pico® remote control (PJ2-3BRL)
• Wire connectors (3)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Phillips-head screwdriver
• Pliers

Works with Energy Efficient Dimmable Light Bulbs

Caséta Wireless dimmers are compatible with various dimmable bulb types:

• LED: up to 150 W
• CFL: up to 150 W
• Halogen: up to 600 W
• Incandescent: up to 600 W

Note: You can mix and match dimmable LED and CFLs, as well as halogen and incandescent light bulbs. Dimmable LED and CFL bulb performance may vary. If you experience flickering or bulbs turning off, visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance. For a complete list of compatible bulbs, visit www.casetawireless.com/bulblist.

Installing Your Dimmer (Single-Pole)

Installation for Lights with One Wall Switch (Single-Pole)

This guide covers single-pole installations (one wall switch controlling a light). For 3-way switch installations (two or more switches controlling a light, like stair lights), please visit www.casetawireless.com/3way for complete instructions and videos.

Important Safety Warning

WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

Installation Steps

1. Step 1: Turn Power Off.

   Turn power off at the circuit breaker.

   [Visual Description: Icon of a circuit breaker with the switch in the 'OFF' position.]

2. Step 2: Remove Existing Switch.

   Remove the wallplate from the existing switch. Pull the switch away from the wall and disconnect all three wires from it.

   [Visual Description: Shows removing a wallplate, then pulling out an old switch from the wall and disconnecting wires.]

3. Step 3: Remove Side Sections (If Necessary).

   For dimmers at the end of a gang (next to an open space or another device), do not remove the outside side sections. For dimmers installed in the middle of a gang, remove the inside side sections. If your switch has more than 3 wires, consult the video at www.casetawireless.com/3way.

   [Visual Description: Diagrams showing how to bend and break off side sections of the dimmer. One diagram shows a dimmer with no side sections removed, one with one side removed, and one with both sides removed. Another shows a dimmer at the end of a gang where outside sections are not removed.]

4. Step 4: Connect the Dimmer.

   Connect the dimmer wires to the wallbox wires using wire connectors:

   • Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector.
   • Connect one of the remaining wires from the wallbox to one of the remaining wires on the dimmer using a second wire connector.
   • Connect the last wire from the wallbox to the last wire on the dimmer using a third wire connector.

   [Visual Description: Diagram illustrating wire connections. Green wire to green wire, and the other two wires connected between the dimmer and the wallbox wires.]

5. Step 5: Mount the Dimmer.

   Secure the dimmer into the wallbox using the provided screws.

   [Visual Description: Dimmer being screwed into the wallbox.]

6. Step 6: Attach the Wallplate.

   Attach the adapter to the dimmer using the provided screws and snap on the wallplate. If you installed the dimmer next to other dimmers or switches, ensure the wallplate has the correct number of openings.

   [Visual Description: Shows attaching an adapter to the dimmer, then snapping the wallplate onto the adapter.]

7. Step 7: Turn Power On.

   Turn power back on at the circuit breaker.

   [Visual Description: Icon of a circuit breaker with the switch in the 'ON' position.]

Important Notes on Installation

• For indoor use only.
• Operate between 32°F (0°C) and 104°F (40°C).

Maximum Wattage Derating Chart

Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for maximum wattage information:

*For maximum wattage information when mixing light bulb types, see www.casetawireless.com/ganging.

Using Your Caséta Wireless Kit

With a Smartphone or Tablet (Bridge Required)

The Caséta Wireless dimmer can be controlled from a smartphone when used with the Lutron Smart Bridge (sold separately). If you are using the dimmer and remote control with the Lutron Smart Bridge, follow the instructions below. If using with another manufacturer’s bridge, please refer to that manufacturer’s instructions for setup.

Setup Steps:

1. Download the Lutron App.

   Search for "Lutron Caseta" in the App Store (Apple) or Google Play (Android) and download the Lutron app.

   [Visual Description: Icons for Apple App Store and Google Play Store.]

2. Launch the Lutron App.

   Open the downloaded Lutron app.

3. Complete Setup.

   Use the Lutron app to complete all remaining setup steps, including adding devices such as Pico remotes and dimmers. The app will guide you through the process.

   [Visual Description: Screenshots or icons representing the Lutron app interface for adding devices, controlling lights, scheduling, and remote access.]

Without a Smartphone or Tablet (Bridge Not Required)

Pairing the Dimmer and Pico Remote Control

1. On the Dimmer: Press and hold the "OFF" button on the dimmer for 6 seconds until the LEDs start blinking.

   [Visual Description: Hand pressing the 'OFF' button on the dimmer.]

2. On the Pico Remote: Press and hold the "OFF" button on the Pico remote control for 6 seconds until the lights flash 3 times.

   [Visual Description: Hand pressing the 'OFF' button on the Pico remote.]

3. Repeat: Repeat these steps to pair other Pico remote controls.

Changing the Favorite Light Level on the Pico Remote Control (Optional)

You can use the round "Favorite" button on the Pico remote control to recall a favorite light level. The default is set to 50%, but you can change it to any level you like.

1. Set Desired Light Level: Adjust the dimmer to your preferred light level.

   [Visual Description: Hand adjusting the dimmer slider to a specific brightness.]

2. Save Favorite Level: Press and hold the "Favorite" button on the Pico remote control for 6 seconds until the LEDs blink twice. The new favorite level is now saved.

   [Visual Description: Hand pressing the 'Favorite' button on the Pico remote.]

Using Your Controls

Dimmer Controls

• ON/OFF: Press the top or bottom of the large button.
• Brighter/Darker: Press and hold the top or bottom of the large button.
• FASS™ Front Accessible Service Switch: Pull out this switch on the in-wall dimmer to remove power at the light socket, typically for replacing light bulbs.

[Visual Description: The in-wall dimmer showing the main button and the FASS™ switch.]

Pico Remote Control

• ON: Press the ON button.
• OFF: Press the OFF button.
• Brighter/Darker: Press and hold the Brighter or Darker buttons.
• Favorite: Press the Favorite button to recall your saved light level.

[Visual Description: The Pico remote control with its buttons labeled: ON, OFF, Brighter, Darker, Favorite.]

Troubleshooting

For additional troubleshooting suggestions, go to www.casetawireless.com/support.

Device Ratings

• In-wall dimmer: PD-6WCL, 120 V~ 50/60 Hz
• Pico remote control: PJ2-3BRL, 3 V - 10 mA (1) CR2032 battery (included)

Important Information

Trademarks: Lutron, Claro, and Pico are registered trademarks and FASS, Caséta, and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Google and the Google logo are registered trademarks of Google Inc., used with permission.

Copyright: © 2014 Lutron Electronics Co., Inc.

Part Number: P/N 0301724 REV B

FCC/IC Information

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warranty

For warranty information, please visit www.casetawireless.com/warranty.

Double Your Warranty

Love Caséta Wireless dimmers? Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. Visit www.casetawireless.com/register.