ℹ️ Document Conversion Notice:
This document has been converted from PDF and formatted to fit this screen. Diagrams and images may be available only in the original here.
Caséta Wireless Quick-Start Guide
Lutron® Smart Bridge, Pico® remote control & in-wall dimmer
Welcome—and thank you for purchasing a Caséta® Wireless dimming kit. Before you install the dimmer, please watch the installation video at www.casetawireless.com/support. We hope you enjoy the convenience of Caséta® Wireless!
Double your warranty: Love Caséta® Wireless dimmers? Have ideas for making them better? Tell us what you think and we'll extend your warranty by 1 year. www.casetawireless.com/register
Contents Supplied
In-wall dimmer (PD-6WCL)
Claro® wallplate (CW-1)
Pico® remote control (PJ2-3BRL)
Wire connectors (x3)
Screws (x2)
Lutron® Smart Bridge (L-BDG2 or L-BDGPRO2)
Power Supply (T-5DC-USB)
Ethernet Cable
Tools You'll Need
Flat-head screwdriver
Phillips-head screwdriver
Pliers
Works with energy efficient dimmable light bulbs:
LED: up to 150 W
Halogen: up to 600 W
Incandescent: up to 600 W
NOTE: You can mix and match dimmable LED, halogen, and incandescent light bulbs with Caséta® Wireless dimmers. Dimmable LED light bulbs vary in their dimming performance. If you're using these bulbs and they flicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance. For a complete list of compatible dimmable LEDs, please visit www.casetawireless.com/bulblist
Installation for lights with one wall switch (single-pole)
1 Turn power off at circuit breaker!
⚠️ WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.
2 Remove existing switch from wall
Remove the wallplate from switch. Remove the switch and pull it away from the wall. Disconnect all three wires* from the switch.
*If your switch has more than 3 wires attached, see the "Installing Caséta® Wireless in a 3-way switch application" video at www.casetawireless.com/3way
3 Remove side sections (if necessary)
Bend back and forth to remove side sections. Note: Do not remove outside side sections on dimmers at the end of a gang.
Each dimmer has inside side sections removed. A dimmer in the middle of a gang has all side sections removed.
Important note: Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for maximum wattage information.
Maximum* wattage derating chart (120 V~ 50/60 Hz)
Side sections removed
None
1 side
2 sides
LED
150 W
150 W
150 W
Incandescent & Halogen
600 W
500 W
400 W
*For maximum wattage information when mixing light bulb types see www.casetawireless.com/ganging
4 Connect the dimmer
Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector.
Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.
5 Mount the dimmer
Use the screws provided.
6 Attach the wallplate
Attach the adapter to the dimmer using the screws provided and snap on the wallplate.
(If you installed the dimmer next to other dimmers or switches, you'll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)
7 Turn power on at circuit breaker
Repeat Steps 1 through 7 to install the second dimmer.
Important note (3-Way): Some lights have one wall switch, while others have two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). We've included instructions for lights with one wall switch (called a single-pole). If your light has more than one switch (called a 3-way), please visit www.casetawireless.com/3way for complete installation instructions and how-to videos.
Using Your Caséta Wireless Kit
1 Install the Lutron® Smart Bridge
A. Connect the Smart Bridge to your Wi-Fi router using the Ethernet cable.
B. Connect the power cord to the Smart Bridge and plug it into an outlet.
FASSTM: Front Accessible Service Switch. Pull the FASSTM switch out on the in-wall dimmer to remove power at the light socket.
Pico® remote control
On (✅)
Favorite (⭐)
Darker (⬇️)
Off (?)
Device Ratings
Device
Rating
In-wall dimmer (PD-6WCL)
120 V~ 50/60 Hz
Lutron® Smart Bridge* (L-BDG2 or L-BDGPRO2)
5 V 300 mA
Pico® remote control (PJ2-3BRL)
3 V 10 mA (1) CR2032 battery (included)
Power supply (T-5DC-USB)
Input: 100–240 V~ 50/60 Hz 100 mA Output: 5 V 550 mA
*Connect to a Class 2, LPS, or SELV, limited energy (<15 W) power source only.
Troubleshooting
Symptoms
Probable cause and action
Light does not turn on or in-wall dimmer LEDs do not light up.
Light bulb(s) burned out.
Breaker is OFF or tripped.
Light not properly installed.
Wiring error.
FASSTM switch on the dimmer is in the Off position.
Light does not respond to Pico® remote control.
The dimmer is not properly paired with the Pico® remote control; The Pico® remote control can be paired with the dimmer using the Lutron® app.
The dimmer is already at the light level the Pico® remote control is sending.
The Pico® remote control is outside the 30 ft (9 m) operating range.
The Pico® remote control battery is low.
The Pico® remote control battery is installed incorrectly.
Bulbs turn off while being dimmed.
Bulbs turn on at high light level but do not turn on at a low light level.
Bulbs flicker or flash when dimmed to a low light level.
Verify bulbs are marked dimmable and visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.
Go to www.casetawireless.com/support for additional troubleshooting suggestions.
Important Notes and Warnings
For indoor use only.
Operate between 32 °F (0 °C) and 104 °F (40 °C).
CAUTION: Use only with permanently installed fixtures with dimmable LED, halogen, or incandescent lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.
Codes
Install in accordance with all national and local electrical codes.
Grounding
When no "grounding means" exist in wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.
HomeKit
Use of the HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
FCC/IC Information
For FCC/IC information, please visit: www.lutron.com/fcc-ic
Warranty
For warranty information, please visit www.casetawireless.com/warranty
Lutron Caséta Wireless: Smart Home Lighting and Control System Discover Lutron Caséta Wireless, a smart home system for seamless control of lights, shades, and temperature. Explore smart dimmers, switches, motorized shades, and integration with smart thermostats for enhanced convenience and energy efficiency.
Lutron Caséta Wireless In-Wall Dimmer & Pico Remote Quick Start Guide Comprehensive quick start guide for installing and using the Lutron Caséta Wireless in-wall dimmer and Pico remote control, including setup, pairing, and troubleshooting. Learn how to replace existing switches, connect wiring, and integrate with smart home systems.
Lutron Caséta Wireless In-Wall Dimmer Quick Start Guide Install and set up your Lutron Caséta Wireless in-wall dimmer and Pico remote control. This guide covers single-pole installation, app setup with Lutron Smart Bridge, and basic operation and troubleshooting.
Lutron Caséta Wireless Advanced Installation Guide Comprehensive guide for installing and configuring Lutron Caséta Wireless dimmers, switches, and remote controls, covering 3-way, multi-location, and advanced setup procedures, including troubleshooting and product specifications.
Lutron Caséta Wireless In-Wall Dimmer Quick Start Guide A quick start guide for installing and using the Lutron Caséta Wireless in-wall dimmer and Pico remote control, covering setup, pairing, bulb compatibility, and troubleshooting.
