Bobtot SoundAir Outdoor Portable Wireless Speaker

What's in the Box

Check to make sure you have everything below:

• A: 1*SoundAir Portable Speaker
• B: 1*USB Charging Cable (Type-C)
• C: 1*Quick Start Guide

Device Overview

The Bobtot SoundAir speaker features:

• Microphone
• Mode Indicator light
• Strap
• Power/TWS/Mode Button
• Play/Pause/Answer Button
• Volume Down/Previous Button
• Volume Up/Next Button
• Charging port

Buttons and Ports

Power/TWS/Mode Button

• Short press to switch mode.
• Double click to activate TWS mode, connect or disconnect with two speakers.
• Long press and hold to turn the speaker on/off.

Play/Pause/Answer Button

• Short press to pause/play the music.
• Short press to accept an incoming call.
• Double click to call back the last number.
• Long press to reject an incoming call.
• Long press to disconnect Bluetooth.

Volume Down/Previous Button

• Short press to turn down the volume.
• Long press to go to the previous song.

Volume Up/Next Button

• Short press to turn up the volume.
• Long press to go to the next song.

Charging Your Device

Plug the included USB Type-C cable into the speaker's charging port and connect the other end to a power adapter (not included). Allow approximately 3.5 hours for a full charge.

• When the battery is low and the red light blinks, please charge it.
• The indicator light is red while charging.
• The red light turns off when fully charged.

Note: Bobtot recommends using a USB wall adapter with a DC5V=1A output.

Charging port: USB Type-C

Initial Setup (Bluetooth Pairing)

1. Once your speaker is fully charged, press and hold the Power button until you hear a voice prompt indicating the device has entered BT pairing mode.
2. On your smartphone or tablet, search for the BT device named "Bobtot SoundAir" and tap to connect.
3. A prompt will play once pairing is successful.

Notes:

• If the speaker is turned on but not connected, it will automatically shut down after 10 minutes.
• If connected but no playback occurs, it will automatically shut down after 20 minutes.

TWS Sync Mode

1. Long press the Power button (approximately 2 seconds) on both speakers to turn them on. The blue light will flash.
2. Quickly double-click the Power button on any one speaker. A prompt sound "connected" indicates the speakers have entered pairing mode, and the indicator light of one speaker will turn solid blue.
3. On your smartphone or tablet, search for the BT device named "Bobtot SoundAir" and connect it. You will hear the sound "connected" again, indicating successful connection. You can now enjoy music with two speakers together.

Notes:

• In TWS Mode, turning off one speaker will turn off both.
• Double-clicking the Power button will disconnect TWS mode.

Light Status

Mode Indicator light:

• Blue light flash: In BT pairing or TWS pairing status.
• Solid blue light: In TWS or BT connection status.
• Red light flash: Low battery.
• Solid red light: Charging.
• Red light off: Full charge.

Hands-Free Calling

• Volume Down/Previous Button: Short press once to decrease volume.
• Volume Up/Next Button: Short press once to increase volume.
• Multi-function Button (Play/Pause/Answer):
  • Short press to accept an incoming call.
  • Short press again to hang up.
  • Double click to call back the last number in any mode.
  • Long press to reject an incoming call.
  • During a call, long press for 2 seconds to switch between phone talking or speaker talking.

Resetting Your Device

If your speaker is not operating properly, you may reset it. To do so, press and hold the Power button for approximately 8 seconds until the speaker powers off, and then power it on again as usual.

Specifications

• Model Name: SoundAir
• Type: Outdoor Portable Wireless Speaker
• Input Power: 5V 1A
• Impedance: 4Ω
• Signal to Noise Ratio: > 78dB
• Water Resistance: IPX7 water-resistant, sprayproof
• Battery: Built-in rechargeable battery
• Microphone: Built-in Mic
• Range: 33ft (10m)
• Frequency Response: 200Hz-18KHz
• TWS Sync Mode: Pair 2 of these speakers together.
• Playtime: Up to 13 hours of playtime (battery life is measured as number of playtime with volume set at 50%).

FCC Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC ID: 2AZ43-ET35

Customer Care

At Bobtot, Bobtot strives to provide exceptional customer care to every one of its clients. Bobtot believes that building strong relationships with customers is essential to the success of its business. To help achieve this goal, Bobtot has put together the following customer care guide:

• Time: Bobtot understands that customers' time is valuable, so Bobtot will respond to any inquiries within 24 hours.
• Feedback: Bobtot knows that customers are the heart of its business, so Bobtot values customer feedback. Bobtot encourages customers to share their thoughts and ideas.
• Solutions: If customers encounter any issues, Bobtot will try its best to find a quick and efficient solution that meets their needs.

If you have any questions or concerns, please do not hesitate to reach out to Bobtot.

Bobtot will be happy to assist you:

Call or Message: +1 888 572 1718

Email: service@bobtot.net

Website: bobtot.net

Technical Requirements (Chinese)

These are the technical requirements for the printing of this document:

1. Finished size: 90*90mm, Unfolded size: 720*90mm
2. 128g coated paper
3. Accordion fold, red dashed line indicates creasing lines and should not be printed.
4. Single black double-sided printing