Parts List
| Item | Description | Quantity of Item | Hardware Required |
|---|---|---|---|
| 1 | Driver/Left Viewpoint Running Board | 1 | 12 x 8-1.25mm x 25mm Hex Bolts |
| 1 | Passenger/Right Viewpoint Running Board | 1 | 24 x 8mm x 24mm OD x 2mm Flat Washers |
| 3 | Driver/Left Mounting Brackets | 3 | 12 x 8mm Lock Washers |
| 3 | Passenger/Right Mounting Brackets | 3 | 12 x 8mm Hex Nuts |
| 6 | 10-1.5mm x 30mm Hex Bolts | 6 | 12 x 6mm T-Bolts |
| 6 | 10mm Lock Washers | 6 | 12 x 6mm x 22mm OD x 2mm Flat Washers |
| 6 | 10mm x 30mm OD x 2.5mm Flat Washers | 6 | 12 x 6mm Lock Washers |
| 6 | 10mm Clip Nuts | 6 | 12 x 6mm Hex Nuts |
Installation Procedure
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
-
Starting from under the front Driver/Left side, temporarily remove the plastic side panel. Move to the floor panel, locate the square holes and two round holes in the pinch weld.
(Refer to Figure 1 for Driver/Left front mounting location.)Select one (1) 10mm Clip Nut. Attach the Clip Nut into the square hole in the floor panel.(Refer to Figure 2 for attaching the 10mm Clip Nut.)
-
Select one (1) Driver/Left Mounting Bracket. Attach the Bracket to the 10mm Clip Nut with one (1) 10mm Hex Bolt, one (1) 10mm Lock Washer and one (1) 10mm Flat Washer. Do not tighten hardware.
(Refer to Figures 3 & 5 for attaching the Driver/Left Mounting Bracket to the Clip Nut and its attachment at the front location.)
-
Attach the Mounting Bracket to the pinch weld with two (2) 8mm Hex Bolts, four (4) 8mm Flat Washers, two (2) 8mm Lock Washers and two (2) 8mm Hex Nuts. Do not tighten hardware.
(Refer to Figure 4 for attaching the Driver/Left Mounting Bracket to the pinch weld.)
-
Move along the body to the center mounting location. Repeat Steps 2–4 to attach the Mounting Bracket to the center location. Do not tighten hardware.
(Refer to Figure 6 for the Driver/Left Center mounting location.)
-
Move to the rear mounting location. Repeat Steps 2–4 to attach the remaining one (1) Driver/Left Mounting Bracket. Do not tighten hardware.
(Refer to Figure 7 for the Driver/Left rear mounting location.)
- Reattach the plastic side panel.
-
Select the Passenger/Right Running Board. Insert six (6) 6mm T-Bolts into the channels in the bottom of the Running Board, three (3) per channel. Place the Running Board on the Brackets. Line up the T-Bolts with the Mounting Brackets. Attach the Running Board to the Brackets with six (6) 6mm Flat Washers, six (6) 6mm Lock Washers and six (6) 6mm Hex Nuts. Do not tighten hardware.
(Refer to Figure 8 for inserting T-Bolts and Figure 9 for attaching the Running Board to the Mounting Brackets.)
- Level and adjust the Running Board and tighten all hardware.
- Repeat Steps 2–8 to attach the Passenger/Right Running Board.
- Perform periodic inspections to ensure that all hardware is secure and tight.
To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Boards.
TAC Truck Accessories Company | TACUSA
