Owner's Manual for TAC models including: BR-FRS-017 Rocker Running Boards, BR-FRS-017, Rocker Running Boards, Running Boards, Boards

PARTS LIST:

Winbo

Installation Instructions

TAC Rocker Running Boards Compatible With 2021-2024 Ford Bronco 2 Door | TACUSA


File Info : application/pdf, 3 Pages, 646.58KB

PDF preview unavailable. Download the PDF instead.

PW04244502 BR-FRS-017 ?v=1728614550
Rocker Step
PART #: BR-FRS-017
FITS: 2021-Up Ford Bronco 2 Door

60-120 min
Cutting Not Required
Drilling Not Required
Part List

Torque & Tools

Fastener Size
 6mm
 8mm  10mm
 12mm

Tightening Torque (ft-lbs)
 7-8.5
 18-20  35-40
 60-70

Wrench Required
 10mm  13mm  16mm  18mm

Allen Wrench Required
 4mm
 5mm  6mm
 8mm

BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

"17-L" for Left/Driver Side

Front

"17-R" for Right /Passenger Side

Driver/Left Side Front
Bracket

Passenger/Right Side Front
Bracket

www.tacautoparts.com

Driver/Left Side Rear
Bracket

Passenger/Right Side Rear
Bracket

Customer Support: tac-office@tacautoparts.com

x8
10mm x 30mm Hex Bolt

x8
10mm Flat Washer

PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE
PASSENGER SIDE INSTALLATION

x8
10mm Lock Washer
FIG 2
(2) 10mm Hex Bolts (2) 10mm Lock Washers (2) 10mm Flat Washers

x8
8mm x 25mm Combo Bolt

STEP 1
Starting from underneath the Passenger/Right body panel, locate the front mounting location and the threaded holes in the body panel, (Fig 1). Remove the plastic plugs covering the holes. FIG 1
Front

(Fig 2) Attach the Passenger/Right Front Mounting Bracket to the front location
STEP 3
Repeat Steps 1-2 to attach (1) Passenger/Right Rear Mounting Brackets to the rear locations, (Figs 3-4). Do not tighten hardware. FIG 3

(Fig 1) Passenger/Right front mounting location
STEP 2
Select the Passenger/Right Front Mounting Bracket. Attach the Mounting Bracket to the front location with (2) 10mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers, (Fig 2). Do not tighten hardware.

Front (Fig 3) Passenger/Right rear mounting location

www.tacautoparts.com

Page 1 of 2

9/30/24 (JH)

FIG 4
(2) 10mm Hex Bolts (2) 10mm Lock Washers (2) 10mm Flat Washers

(Fig 4) Attach (1) Passenger/Right Rear Mounting Bracket to the rear location.

STEP 4

Select the Passenger/Right Running Board.
NOTE: The Passenger/Right Running Board will have a "17-R" on the front. Carefully place Running Board on the brackets. Attach Running
Board to the (2) Mounting Brackets with (4) 8mm
Combo Bolts, (Fig 5). Do not tighten hardware.

FIG 5

Front

STEP 5
Level and adjust the Running Board and fully tighten all hardware.
STEP 6
Repeat Steps 1--5 to attach the Driver/Left Running Board.
STEP 7
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Attention
To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
Mild soap may be used also to clean the Running Boards.

(2) 8mm Combo Bolts
(Fig 5) Attach Passenger/Right Running Board to the Mounting Brackets

www.tacautoparts.com

Page 2 of 2

9/30/24 (JH)



References

WPS 文字