Intelbras FS 3010 V Solenoid Lock User Manual

Introduction

Congratulations on acquiring an Intelbras product. The FS 3010 V solenoid lock is designed for glass doors with glass frames. Manufactured with high-strength aluminum and brushed stainless steel, it can be installed on doors that open inwards or outwards, to the right or left. It is suitable for standard market doors with perforations or cutouts.

Safety Precautions

• LGPD - General Law for the Protection of Personal Data: Intelbras does not access, transfer, capture, or process personal data from this product.
• The lock should not be installed on the outside of doors.
• Install the lock only in covered areas protected from water.
• Always install the lock as close as possible to its frame.
• The maximum recommended gap between the lock and the frame is 5 mm.
• In the absence of electricity, the lock unlocks. Always install with a charger and battery.
• Do not use the exclusive output for electric locks / electromechanical systems of intercoms and video intercoms unless it is a dry contact (relay).
• Do not install on sliding doors.
• The power wiring for the button and the lock should pass through the lower part of the solenoid coil.
• The use of a hydraulic closer is recommended for automatic door closing.
• Attention: Do not use grease, oil, or other lubricants on the bolt or any other part of the lock.

Diagram Description: A diagram shows the internal mechanism of the lock, highlighting the cable entry zone.

Attention: For the correct positioning of the plastic part below.

Diagram Description: Two diagrams illustrate the correct positioning of a plastic part, showing how it fits into the lock mechanism.

Preventive Maintenance

To ensure the correct functioning of the lock, it is recommended to clean its actuation system components every 6 months. Follow these steps:

1. Open the lock.
2. Remove the screws holding the bolt cover.
3. Remove the bolt cover.
4. Remove the bolt.
5. Remove the bolt bushing.
6. Clean the bolt and bushing with a clean cloth and alcohol.
7. Clean the cover and the movement channel (regions shown in the image below) with a clean cloth and alcohol.
8. Reassemble the bushing into the lock base.
9. Mount the bolt in the lock's movement channel.
10. Place the bolt cover on the lock base and secure the assembly.

Diagram Description: An exploded view of the lock components, including the bolt bushing, bolt, bolt cover, screws, and actuation channel, with labels for each part and cleaning zones.

Technical Specifications

Product Components

Included Items:

• 1 × FS 3010 V Lock.
• 1 × Strike plate.
• 1 × Exterior handle.
• 1 × Exterior lock plate.
• 1 × Strike plate mirror.
• 2 × Supports for doors with cutouts.
• 4 × Counter screws.
• 1 × Adhesive foam for the strike plate.
• 4 × Phillips screw M4 × 12 mm.
• 4 × Phillips screw M4 × 16 mm.

Diagram Description: Multiple diagrams illustrate the included components: strike plate, lock, exterior handle, exterior lock plate, strike plate mirror, supports for doors with cutouts, counter screws, and adhesive foam.

Installation

The FS 3010 V solenoid lock is designed to work with most electronic intercoms or power supplies with a 12 Vdc / 1 A output.

Obs.: Never plug directly into the mains (110/220 V).

Doors with Cutouts or Perforations

The FS 3010 V lock can be installed on doors with either cutouts or perforations.

Diagram Description: Two diagrams show the dimensions and placement for installing the lock on a door with a cutout and a door with perforations. Dimensions for minimum and maximum door thickness and cutout/perforation sizes are indicated.

Strike Plate Installation on Doors with Cutouts

For doors opening outwards: Pay attention to the installation of the strike plate mirror.

Diagram Description: Diagram showing the installation of the strike plate on a door opening outwards, including the strike plate mirror.

For doors opening inwards: In this application, do not use the strike plate mirror on the door; it should be fixed with the lock.

Obs.: The adhesive foam should be attached to the lock handle, not the glass.

Diagram Description: Diagram showing the installation of the strike plate on a door opening inwards, with the adhesive foam applied to the lock handle.

Lock Installation on Fixed Glass with Cutout

For doors opening outwards:

Obs.: The adhesive foam should be attached to the lock handle, not the glass.

Diagram Description: Diagram illustrating the installation of the lock on a fixed glass door opening outwards, with adhesive foam.

For doors opening inwards:

Diagram Description: Diagram illustrating the installation of the lock on a fixed glass door opening inwards.

Strike Plate Installation on Doors with Perforations

For doors opening outwards: Pay attention to the installation of the strike plate mirror.

Diagram Description: Diagram showing the installation of the strike plate on a door with perforations opening outwards, including the strike plate mirror.

For doors opening inwards: In this application, do not use the strike plate mirror on the door; it should be fixed with the lock.

Diagram Description: Diagram showing the installation of the strike plate on a door with perforations opening inwards, with the strike plate fixed with the lock.

Lock Installation on Fixed Glass with Perforation

For doors opening outwards:

Diagram Description: Diagram illustrating the installation of the lock on fixed glass with perforations, opening outwards, with adhesive foam.

For doors opening inwards:

Diagram Description: Diagram illustrating the installation of the lock on fixed glass with perforations, opening inwards, with the strike plate mirror.

Connections

The FS 3010 V solenoid lock is designed to work with most electronic intercoms or power supplies with a 12 V / 1A output, and with access controllers that operate with 12 V and have a timed dry contact output.

Connection Diagram using FA 1220S Power Supply:

Diagram Description: A wiring diagram shows the connection of the lock to an exit button and the FA 1220S power supply, illustrating the wiring for the button input, NC lock connection, and power supply.

Connection Diagram using Market Power Supply:

Diagram Description: A wiring diagram shows the connection of the lock to an exit button and a generic 12 Vdc / 1 A power supply, illustrating the wiring for the button input, NC lock connection, and power supply.

Timing Adjustment

It is possible to adjust the blocking time between 0 (automatic lock), 3, and 6 seconds by simply moving the selection switch to the desired position.

Obs.: For doors with a closer, it is not recommended to use the timer at 0 seconds.

Diagram Description: A diagram shows the internal mechanism with a switch indicating the 0, 3, and 6-second timing options.

Cable Size Table

Obs.: Table valid for good quality copper cables.

Frequently Asked Questions

Warranty Policy

Imported by: Intelbras S/A - Industria de Telecomunicación Electrónica Brasileña, Rodovia SC 281, km 4.5 – Sertão do Maruim – São José/SC – Brasil – 88122-001, CNPJ 82.901.000/0014-41.

Intelbras S/A undertakes to repair or replace defective parts and components of the product, including labor, or the entire product, for the period described in the warranty term. For the validity of this warranty, the product must be presented at the Call Center, accompanied by: this policy duly sealed by the establishment where it was purchased, or by the invoice, receipt, or proof of purchase.

The repair time will not exceed 30 calendar days from the date of product receipt at the Service Center.

THIS WARRANTY IS NOT VALID IN THE FOLLOWING CASES:

• a. When the product has been used under conditions other than normal.
• b. When the product has not been installed or used according to the User Manual provided with it.
• c. When the product has been altered or repaired by persons not authorized by Intelbras S/A.
• d. When the product has suffered damage caused by: accidents, incidents, natural phenomena (lightning, floods, landslides, etc.), humidity, power grid variations (overvoltage caused by accidents or excessive grid fluctuations), installation/use not in accordance with the user manual or resulting from natural wear and tear of parts, components; chemical, electromagnetic, electrical or animal influences (insects, etc.).
• e. When the product's serial number has been altered or scratched.

Warranty Terms

It is expressly stated that this contractual warranty is granted under the following conditions:

• Customer Name:
• Customer Signature:
• Invoice No.:
• Date of Purchase:
• Model:
• Serial No.:
• Reseller:

1. All parts, pieces, and components of the product are guaranteed against manufacturing defects for a period of 1 (one) year - consisting of 3 (three) months of legal warranty and 9 (nine) months of contractual warranty - starting from the date of purchase by the consumer, as stated on the product invoice, which is an integral part of this Term throughout the national territory. This contractual warranty includes the express replacement of products with manufacturing defects. If no manufacturing defect is detected, but defects arising from improper use are found, the consumer will bear the costs.
2. Product installation must be carried out according to the Product Manual and/or Installation Guide. If your product requires installation and configuration by a qualified technician, seek a competent and specialized professional, as the costs of these services are not included in the product price.
3. Upon detection of a defect, the Consumer must immediately contact the nearest Authorized Service Center listed by the manufacturer. Only these are authorized to examine and rectify the defect during the warranty period. Failure to comply with this will void the warranty, as it will be considered that the product has been tampered with.
4. In case the Consumer requests home service, they must contact the nearest Authorized Service Center to inquire about the technical visit fee. If the product needs to be removed, the resulting costs, such as transportation and security for the product's round trip, will be the responsibility of the Consumer.
5. The warranty will be completely void in the event of any of the following hypotheses: a) if the defect is not manufacturing-related, but caused by the Consumer or third parties unrelated to the manufacturer; b) if the product damage is a consequence of accidents, incidents, natural phenomena (lightning, floods, landslides, etc.), humidity, power grid voltage (overvoltage caused by accidents or excessive grid fluctuations), installation/use not in accordance with the user manual or resulting from natural wear and tear of parts, components; c) if the product has been subjected to chemical, electromagnetic, electrical or animal influences (insects, etc.); d) if the product's serial number has been altered or defaced; e) if the appliance has been tampered with.
6. This warranty does not cover data loss. It is recommended that the Consumer regularly back up product data, if applicable.
7. Intelbras is not responsible for the installation of this product, nor for any attempt at fraud and/or sabotage of its products. Keep software and application updates current, as well as necessary network protections against intrusions (hackers). The equipment is guaranteed against defects within its normal usage conditions. It is important to be aware that, being an electronic device, it is not immune to fraud and scams that may interfere with its proper functioning.
8. Dispose of your product properly after its useful life: hand it in at collection points for electrical and electronic products, at an authorized Intelbras technical assistance center, or consult our website www.intelbras.com.br and support@intelbras.com or call (48) 2106-0006 or 0800 7042767 for more information.

Intelbras S/A reserves the right to modify the general, technical, and aesthetic characteristics of its products without prior notice.

All images in this manual are illustrative.

Contact Information

Attention to the customer: +55 (48) 2106 0006

Support via e-mail: soporte@intelbras.com

Imported in Brazil by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira, Rodovia SC 281, km 4.5 – Sertão do Maruim – São José/SC – 88122-001, CNPJ 82.901.000/0014-41 – www.intelbras.com.br | www.intelbras.com/es

Manufactured in China