Technical Specification for MEAN WELL models including: MEAN WELL, HLG-240H-C, HLG-240H-C700, HLG-240H-C1050, HLG-240H-C1400, HLG-240H-C1750, HLG-240H-C2100, 250W LED Driver, Constant Current LED Driver, LED Power Supply, IP67, IP65, Dimming, Technical Specification
250W Constant Current Mode LED Driver
HLG-240H-C series
User's Manual
IP65 IP67
~
A
Dx
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
HLG-240H-C series
SPECIFICATION
MODEL
HLG-240H-C700
HLG-240H-C1050
HLG-240H-C1400
HLG-240H-C1750
HLG-240H-C2100
OUTPUT
RATED CURRENT
700mA
1050mA
1400mA
RATED POWER
249.9W
249.9W
250.6W
CONSTANT CURRENT REGION Note.2 178 ~ 357V
119 ~ 238V
89 ~ 179V
OPEN CIRCUIT VOLTAGE (max.) 360V
241V
182V
CURRENT ADJ. RANGE
Can be adjusted by internal potentiometer (A/AB type only)
350 ~ 700mA
525 ~ 1050mA
700 ~ 1400mA
1750mA 250.25W 71 ~ 143V 146V
875 ~ 1750mA
2100mA 249.9W 59 ~ 119V 122V
1050 ~ 2100mA
CURRENT RIPPLE
5.0% max. @rated current
CURRENT TOLERANCE
±5%
SET UP TIME
Note.4 1000ms/115VAC, or 500ms/230VAC
VOLTAGE RANGE
90 ~ 305VAC 127 ~ 431VDC Note.3
(Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF0.98/115VAC, PF0.95/230VAC, PF0.92/277VAC @full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
INPUT
THD< 20% (@ load50% /115VAC, 230VAC; @ load75%/277VAC) TOTAL HARMONIC DISTORTION
(Please refer to "TOTAL HARMONIC DISTORTION (THD)" section)
EFFICIENCY (Typ.)
93.5%
93.5%
94%
94%
93.5%
AC CURRENT (Typ.)
2.5A / 115VAC 1.3A / 230VAC 1.1A / 277VAC
INRUSH CURRENT(Typ.)
COLD START 75A(twidth=700s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
2 units (circuit breaker of type B) / 3 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
SHORT CIRCUIT PROTECTION OVER VOLTAGE
Constant current limiting, recovers automatically after fault condition is removed
375 ~ 410V
250 ~ 275V
188 ~ 206V
150 ~ 165V
Shut down and latch off o/p voltage, re-power on to recover
125 ~ 137V
OVER TEMPERATURE
Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP.
Tcase=-40 ~ +90(Refer to "Derating Curve")
MAX. CASE TEMP.
Tcase=+90
WORKING HUMIDITY
20 ~ 95% RH non-condensing
ENVIRONMENT
STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/ (0 ~ 50)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750(type"HL"), CSA C22.2 No. 250.13-12; BS EN/EN/AS/NZS 61347-1, BS EN/EN/AS/NZS 61347-2-13, BS EN/EN62384 independent; GB19510.1,GB19510.14; IP65 or IP67, EAC TP TC 004 approved
SAFETY & EMC
WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@ load50%) ; BS EN/EN61000-3-3,GB/T 17743 , GB17625.1, EAC TP TC 020
EMC IMMUNITY MTBF
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, light industry level (surge immunity Line-Earth 4KV, Line-Line 2KV),EAC TP TC 020
2513.7K hrs min. Telcordia SR-332 (Bellcore) ; 228.5K hrs min. MIL-HDBK-217F (25)
OTHERS NOTE
DIMENSION
244.2*68*38.8mm (L*W*H)
PACKING
1.3Kg; 12pcs/16.6Kg/0.84CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De-rating may be needed under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details.
4. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 6. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains.
7. This series meets the typical life expectancy of >62,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75 or less.
8. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com.
9. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 10. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
BLOCK DIAGRAM
EMI FILTER
I/P
&
RECTIFIERS
FG
PFC CIRCUIT
POWER SWITCHING
PFC CONTROL
O.L.P.
PWM & PFC CONTROL
HLG-240H-C series
RECTIFIERS &
FILTER
Fosc(PFC) : 50KHz Fosc(PWM) : 65KHz
O.L.P.
DETECTION CIRCUIT
+V
-V
DIM+ DIM(B Type)
O.V.P.
DRIVING METHODS OF LED MODULE
This series works in constant current mode to directly drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
100
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
Constant Current area
50
Vo(%)
50
100
Io (%)
Typical output current normalized by rated current (%)
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
DIMMING OPERATION
HLG-240H-C series
FG (Green/Yellow) AC/L(Brown) AC/N(Blue)
3 in 1 dimming function (for B/AB-Type)
HLG-240H-C
-V(Blue) +V(Brown)
DIM+(Purple)* DIM-(Pink)**
* DIM+ for B-Type PROG+ for D2-Type
* *DIM- for B-Type PROG- for D2-Type
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
Applying additive 1 ~ 10VDC
100%
+ +V
90%
+
80%
Output current (%)
-V
70%
-
60%
DIM+
50%
+
Additive Voltage
40%
-
30%
DIM-
20%
"DO NOT connect "DIM- to -V"
10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
+ +V
+
-
-V
-
DIM+
Additive PWM signal
DIM-
"DO NOT connect "DIM- to -V"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
+
+V
+
-
-V
-
DIM+
Additive Resistance
DIM-
"DO NOT connect "DIM- to -V"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
HLG-240H-C series
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.
N FG L
Relay
Switch
Adjuster
10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal
Green/ Yellow
Brown
Blue
AC/L AC/N
HLG-240H-C B-Type
DIM+ DIM-
V(-) V(+)
Purple Pink Blue Brown
LED Lighting Fixture
Using a switch and relay can turn ON/OFF the lighting fixture.
Smart timer dimming function (for Dxx-Type by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details.
Ex : D01-Type: the profile recommended for residential lighting
Set up for D01-Type in Smart timer dimming software program:
T1
T2
T3
T4
TIME**
06:00
07:00
11:00
---
LEVEL** 100%
70%
50%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a residential lighting application adopts D01-Type, when turning on the power supply at 6:00pm, for instance:
[1] The power supply will switch to the constant current level at 100% starting from 6:00pm. [2] The power supply will switch to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on.
The constant current level remains till 8:00am, which is 14:00 after the power supply turns on.
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
HLG-240H-C series
Ex: D02-Type: the profile recommended for street lighting
Set up for D02-Type in Smart timer dimming software program:
TIME** LEVEL**
T1 01:00 50%
T2 03:00 80%
T3 8:00 100%
T4
T5
11:00
---
60%
80%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a street lighting application adopts D02-Type, when turning on the power supply at 5:00pm, for instance: [1] The power supply will switch to the constant current level at 50% starting from 5:00pm. [2] The power supply will switch to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on. [5] The power supply will switch to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The
constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
Ex: D03-Type: the profile recommended for tunnel lighting
Set up for D03-Type in Smart timer dimming software program:
T1
T2
T3
TIME**
01:30
11:00
---
LEVEL** 70%
100%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a tunnel lighting application adopts D03-Type, when turning on the power supply at 4:30pm, for instance: [1] The power supply will switch to the constant current level at 70% starting from 4:30pm. [2] The power supply will switch to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
HLG-240H-C series
OUTPUT LOAD vs TEMPERATURE(Note.8)
LOAD (%)
230VAC
100
100
LOAD (%)
80
80
60
110VAC
60
40
40
20
20
-40 -25 -10
0
15 30 50 60 70 (HORIZONTAL)
AMBIENT TEMPERATURE,Ta ()
-40 -25 0
20
45
55
65
75
90 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
90 110 125 135 145 155 165 175 180 200 230 305
INPUT VOLTAGE (V) 60Hz
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 80
1 0 .9 0 .8 0 .7 0 .6 0 .5 0 .4
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% (250W)
LOAD
277V 230V 115V
LOAD (%)
TOTAL HARMONIC DISTORTION (THD)
1400mA Model, Tcase at 80
30 25 20 15 10 5 0
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277V 230V 115V
LOAD
EFFICIENCY(%)
EFFICIENCY vs LOAD
HLG-240H-C series possess superior working efficiency that up to 94% can be reached in field applications. 1400mA Model, Tcase at 80
100 95 90 85 80 75 70 65 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
277V 230V 115V
THD(%)
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
LIFETIME
HLG-240H-C series
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
Tc a s e ()
File Name:HLG-240H-C-SPEC 2024-07-19
250W Constant Current Mode LED Driver
HLG-240H-C series
MECHANICAL SPECIFICATION
A-Type
12 9.6
300±20 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) SJOW 17AWG&H05RN-F 1.0mm²x3C
244.2 220.2
tc
9.4 34.2 9.4 68
34
tc : Max. Case Temperature
Case No.954F Unit:mm Tolerance:±1
110.1
300±20
-V(Blue)
SOOW 17AWG&H07RN-F 1.0mm²x2C +V(Brown)
Io
(for HLG-240H-C700)
ADJ. SJOW 17AWG&H05RN-F 1.0mm²x2C(for others)
4.2×4PL
38.8
B/D2-Type
12 9.6
300±20
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
SJOW 17AWG&H05RN-F 1.0mm²x3C
244.2 220.2
tc
9.4 34.2 9.4 68
34
tc : Max. Case Temperature
110.1
300±20 SJOW 17AWG&H05RN-F 1.0mm²x2C
-V(Blue) +V(Brown)
DIM+(Purple)* DIM-(Pink)**
SOOW 17AWG&H07RN-F 1.0mm²x2C 4.2×4PL (for HLG-240H-C700)
SJOW 17AWG&H05RN-F 1.0mm²x2C(for others)
* DIM+ for B-Type PROG+ for D2-Type
* *DIM- for B-Type PROG- for D2-Type
38.8
AB-Type
12 9.6
300±20
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
SJOW 17AWG&H05RN-F 1.0mm²x3C
244.2 220.2
tc
9.4 34.2 9.4 68
34
tc : Max. Case Temperature
110.1
300±20
-V(Blue)
+V(Brown)
SJOW 17AWG&H05RN-F 1.0mm²x2C DIM+(Purple)
Io
DIM-(Pink)
ADJ.
SOOW 17AWG&H07RN-F 1.0mm²x2C
4.2×4PL (for HLG-240H-C700)
SJOW 17AWG&H05RN-F 1.0mm²x2C(for others)
38.8
INSTALLATION MANUAL
Please refer to :http://www.meanwell.com/manual.html
File Name:HLG-240H-C-SPEC 2024-07-19
Corel PDF Engine Version 16.1.0.843
Related Documents
MEAN WELL HLG-240H Series: 240W LED Driver Datasheet Comprehensive technical specifications, features, applications, and operational details for the MEAN WELL HLG-240H series 240W Constant Voltage and Constant Current LED driver. Includes IP65/IP67 ratings, dimming options, and mechanical data.
MEAN WELL HLG-240H-C Series 250W Constant Current LED Driver The MEAN WELL HLG-240H-C series is a 250W constant current LED AC/DC driver, designed for high-efficiency indoor and outdoor lighting applications. Featuring IP67/IP65 protection, active PFC, and various dimming options including 3-in-1 and smart timer dimming, it offers optimal design flexibility for LED street lighting, fishing lamps, harbor lighting, building architectural lighting, and bay lighting. This series operates from 90-305VAC with models ranging from 700mA to 2100mA, ensuring robust performance and a typical lifetime exceeding 62,000 hours.
MEAN WELL HLG-240H Series: 240W Constant Voltage/Current LED Driver Specifications Detailed technical specifications, features, applications, and performance data for the MEAN WELL HLG-240H series 240W LED drivers. Covers constant voltage and constant current modes, IP67/IP65 ratings, wide input voltage range, dimming options, and mechanical dimensions.
MEAN WELL HLG-120H-C Series 150W Constant Current LED Driver Overview of the MEAN WELL HLG-120H-C series, a 150W AC/DC LED driver with constant current mode, high efficiency, IP67/IP65 rating, and various dimming options for indoor and outdoor LED lighting applications.
MEAN WELL HLG-185H-C Series 200W Constant Current LED Driver Detailed specifications and features of the MEAN WELL HLG-185H-C series 200W constant current LED drivers, including applications, model encoding, electrical and environmental specifications, dimming operations, and installation guidelines.
MEAN WELL HLG-120H-C Series 150W Constant Current LED Driver Datasheet Datasheet for the MEAN WELL HLG-120H-C series, a 150W Constant Current Mode LED Driver with features like IP67/IP65 rating, active PFC, and various dimming options. Includes technical specifications, applications, and mechanical dimensions.
MEAN WELL HLG-120H Series: 120W LED Driver Datasheet & Specifications Comprehensive technical specifications, features, applications, dimming options, performance data, and mechanical details for the MEAN WELL HLG-120H series 120W Constant Voltage + Constant Current LED Driver. Suitable for various LED lighting applications with IP67/IP65 ratings.
MEAN WELL HLG-150H Series: 150W AC/DC LED Driver Datasheet Comprehensive datasheet for the MEAN WELL HLG-150H series 150W AC/DC LED driver. Features dual mode constant voltage and constant current output, IP67/IP65 rating, wide operating temperature range, and multiple dimming options for various LED lighting applications.
