Motorized Cellular Shade with Dual Motor Manual
Model Numbers: DMCS1-A, DMCS1-B
Product Models and Specifications
This manual covers two models of motorized cellular shades:
- DMCS1-A: AC Adapter powered
- DMCS1-B: Li-ion Battery powered
Specifications Table
| NO. | Item | Specification |
|---|---|---|
| 1 | Power Source | DMCS1-A: AC Adapter DMCS1-B: Li-ion Battery |
| 2 | Input | DMCS1-A: 100-240V, 50/60 Hz DMCS1-B: 24V, 1.5A Max |
| 3 | Output | DMCS1-A: 24V, 1.1A Max. DMCS1-B: 10.89V, 1.3A Max. |
| 4 | Radio type | 2.4G RF |
| 5 | Motor type | Brush DC motor |
| 6 | Charging type | Power Charger PB-01S (for Battery Model) |
| 7 | Charging Time | < 2 hours |
| 8 | Charging Temperature | 5°C ~ 35°C / 41°F ~ 95°F |
| 9 | Operating Temperature | 0°C ~ 40°C / 32°F ~ 104°F |
| 10 | Relative Humidity | 0% ~ 90% (Non-condensing) |
FCC ID: Q3V-DMCS1
IC ID: 28542-DMCS1
Compliance: CAN ICES-003 (B) / NMB-003(B)
[FCC and IC certification logos]
Component Checks
For DMCS1-A (AC Adapter):
Verify the following components are included:
- 36W AC Adapter
- 6.6 ft. Extension Cable (Optional, for 36W adapter)
- 6 ft. Power Cable (for 65W adapter)
Note: For 65W adapter only. To direct wire, the plug can be removed by a licensed electrician.
For DMCS1-B (Battery):
Verify the following components are included:
- Wireless (with Rechargeable Battery) / Model# PB-01S
- Charging Wand (Optional)
Note: Wired (without Rechargeable Battery) / Model# PB-02 is also available.
Tools You Will Need
- Level
- Measuring Tape
- Pencil
- Power Drill (6mm hex driver and drill bit)
- Screwdriver
Fasteners for Mounting Surfaces:
| Surface | Fastener |
|---|---|
| Wood | Screws (Provided) |
| Drywall/Plaster | Wall Anchors, Expansion Bolts (Not Provided) |
| Metal | Sheet Metal Screws (Not Provided) |
Getting Started
Check Standard Components/Hardware:
- Installation Bracket
- Installation Bracket Screw
- Spacer (Optional)
- Hold Down Bracket (Optional) & Its Screw
Hardware Standard Quantity:
| Order Width (X) | Less or Equal to 64" | Between 64-1/8" and 112" | Over 112" |
|---|---|---|---|
| Installation Bracket | 2 | 3 | 4 |
| Installation Bracket Screw | 4 | 6 | 8 |
| Spacer Block (Optional) | Varies per order request: 1pc/bracket or 2pcs/bracket | ||
| Hold Down Bracket (Optional) | 2 | 2 | 2 |
| Hold Down Bracket Screw (Optional) | 4 | 4 | 4 |
Reading Before Installation
WARNING!
Important safety instructions. Follow all instructions since incorrect installation can lead to severe injury.
Before installing the device, remove any unnecessary cords or components and disable any equipment not needed for powered operation.
WARNING!
The installation height will vary according to product type or installation situation and may exceed 98.43" (2.5m).
WARNING!
For the shade powered by battery (DMCS1-B), please turn on the shade AFTER installation. Press and hold the shade button for 3 seconds, and the green light will flash, which means the shade is powered on.
Reserve space before installation:
For Model# DMCS1-A: Make sure to provide proper accessibility to an electrical outlet.
IMPORTANT!
Wiring and servicing of these products should be referred to qualified personnel.
Mounting Installation Brackets
The installation bracket may be used for INSIDE or OUTSIDE mounts.
Mounting the brackets level is essential for proper operation of the shade.
Shim the brackets if necessary to achieve a level alignment. The bracket requirements and placement are the same for inside and outside mount.
Measure 8 inches from both ends of the headrail. Mark the bracket location on the mounting surface. Proper alignment of brackets will make installation easier.
[Diagram showing measurements: 8 inches from each end of the headrail]
Inside Mount:
Allow a minimum of 1/16 inch distance from the front of brackets to the edge of window opening as shown in the drawing. Use two installation screws to secure brackets. Use wall anchors for drywall or plaster wall.
[Illustration showing inside mount bracket placement with 1/16 inch clearance]
Note: You will hear a click sound once the head rail is properly secured.
Outside Mount:
Use 2 flat head screws to secure each bracket. Use wall anchors for drywall or plaster wall.
[Illustration showing outside mount bracket placement]
Note: If spacer block is provided, please follow this guide: Please always make sure the raised side of the spacer block is against the bracket.
Install Hold Down Bracket (Optional):
A. For Hold Down Brackets:
Use screw to secure each bracket.
[Illustration showing installation of hold down brackets]
Note: For shallow mounting, use 2 flat head screws to secure the bracket as shown in the drawing.
B. For Magnetic Hold Down:
Use M3x15mm screw to secure the magnet catch at the specified location.
Make sure the magnet catch aligns with the pre-installed magnet on the shade bottom rail.
[Illustration showing placement of magnetic hold down components: magnet catch on the shade bottom rail and corresponding magnet on the bracket, with measurements 1 7/16 inches (37mm) and 5/16 inches (8mm)]
Install the Shade
Position the head rail at an angle so that it is hooked to the front of the bracket. Then push it upward at the back to snap into the bracket.
[Illustration showing the shade head rail being angled and pushed upwards to snap into the bracket]
Note: You will hear a click sound once the head rail is properly secured.
Remove the Shade
Fully raise the shade, and then gently remove the bracket off the headrail with a flat screwdriver. Remove the shade.
[Illustration showing shade removal using a flat screwdriver]
Congratulations!
You have finished installing the product.
To ensure a perfect user experience, we encourage you to follow the QR code below to browse additional resources, including how to operate, how to charge, and troubleshooting guides.
Please also note that for shades with rechargeable batteries, the current charge level of the batteries is about 50%.
[A QR code is present for scanning to access additional resources.]
