HOMCOM 700-167V90 Massage and Heating Recliner
Important: Retain for future reference. Read carefully.
General Information
This product is intended for domestic use only.
Maximum Load Capacity: 130kg
Assembly Steps: 6
Operating Time: 0.5 HR
Instructions for Use
- Place the chair stably on a flat floor.
- Keep away from open flames and heat sources.
- Avoid overloading the chair.
Precautions Before Assembly
- Prepare a clean and dry mounting area.
- Verify that the product is not damaged.
- Check that all parts are present.
Maintenance
- Clean with a soft fabric.
- Regularly check the seating.
Storage Conditions
- Store the fabric in a completely dry, clean, and dry place to avoid mold.
Safety Warnings
Beware of crushing and cutting hazards during assembly.
The manufacturer is not responsible for damages due to improper installation or environmental factors.
Warning! Replacement or repair of components for height adjustment with energy storage must only be performed by qualified personnel.
Electrical Parts Safety:
- This appliance can be used by children aged 8 and above, and persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
- The appliance must only be used with the provided power supply unit.
- The external flexible cable or cord of this transformer cannot be replaced; if the cord is damaged, the transformer shall be scrapped.
- If the appliance has a heated surface, persons insensitive to heat must be careful when using the appliance.
- The power supply unit shall not be used if the pins of the plug part are damaged.
Parts List
Parts:
- A x1
- A-1 x1
- B x1
- C x2
- D x1
- E x2
- L x1
- M x1
Hardware:
- F x7 (M8*70)
- G x2 (M8*30)
- H x8 (M6*25)
- I x8 (M4*16)
- J x7
- K x1
Note: Do not confuse similar screws. Do not tighten bolts fully until all parts are connected!
Assembly Instructions
Step 01:
Connect part B to part A.
Step 02:
Attach part A to part B using screws F and washers J.
Step 03:
Connect part E to the chair frame using screws I and washers H.
Step 04:
Attach part D to the chair frame using screws F, G, and washers J.
Step 05:
Connect the power cord (L) to the massage unit (M).
Step 06:
The power adapter (A-1) specifications are listed in the table:
| Input voltage | 100-240 V |
|---|---|
| Input AC frequency | 50/60 Hz |
| Output voltage | 12 V |
| Output current | 1.2 A |
| Output power | 14.4 W |
| Average active efficiency | 83.92 % |
| Efficiency at low load (10 %) | 73.92 % |
| No-load power consumption | 0.1 W |
Functional Description of Massager
I. Graphic presentation of Controller
- POWER: Turn on/off selection key
- HEAT: Heating on/off key
- INTENSITY: Strong/weak selection key
- MODE: Working mode selection key
- BACK: Back massage function selection key
- LUMBAR: Lumbar massage function selection key
- THIGH: Thigh massage function selection key
- LEG: Leg massage function selection key
- TIMER: Set working time key
II. Operating Instructions
- Insert the power into the DC socket.
- Press the POWER key to start the unit. The unit will enter the first mode and run for 15 minutes in the medium step, with all corresponding indicators illuminated.
- Press the HEAT key to turn on the heating function.
- Press the TIMER key; the unit's control time will switch between 15min, 30min, and 60min.
- Press the FUNCTION key to select different working modes (PULSE, PRESS, WAVE, AUTO, NORMAL).
- Press the INTENSITY key to select the high and low intensity of vibration.
- Press the BACK, LUMBAR, and THIGH keys to massage different parts of the body.
