Sealey LED301 3W COB & 2W SMD LED Rechargeable Inspection Light with 180° Magnetic Stand

Introduction

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. Safety

1.1. General

• ? DO NOT shine directly into your, another person's, or an animal's eyes.
• ? DO NOT allow children to use the torch.
• ? DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
• ? DO NOT attempt to repair/disassemble the light yourself.
• ? DO NOT leave batteries in a discharged state. Before storage, remove batteries.
• ? DO NOT use/store the product in extreme temperatures.
• ℹ️ Protect this product from water, humidity, or any liquids.

1.2. Battery Safety

⚠️ WARNING! To reduce the risk of burns or fire:

• ? DO NOT attempt to open the batteries.
• ? DO NOT crush, puncture, short contacts, or dispose of in fire or water.
• ? DO NOT expose to temperatures above 60°C (140°F).
• ℹ️ Replace only with the batteries designed for this product.
• ℹ️ Recycle or dispose of used batteries as stipulated by local regulation.
• ℹ️ If the electrolyte in the batteries gets on your skin, rinse thoroughly with water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

2. Introduction

This is a lightweight inspection light featuring a super bright 3W COB LED, which provides an even and constant spread of light, producing up to 200 lumens. It also includes a 2W High power SMD LED torch producing up to 100 lumens. The unit has an integral hanging hook/belt clip and a magnetic base which can rotate through 180° for hands-free applications. It is powered by a rechargeable 3.7V 1.2Ah lithium-ion battery for longer product life and is supplied with a 300mm USB TYPE-C charging cable.

3. Specification

Light Source Description: The product features a main 3W COB LED for wide illumination and a 2W SMD LED for focused light. It includes an integral hanging hook, belt clip, and a magnetic base that rotates 180° for versatile positioning.

4. Operation

4.1. Charging

• 4.1.1. Use the USB cable provided to charge the product.

4.2. Press ON/OFF

• 4.2.1. Once to turn on the torch (SMD LED).
• 4.2.2. Twice to turn on the COB LED.
• 4.2.3. Three times to turn OFF.

Location Indicators:

• ON/OFF button is located on the back of the unit.
• USB Charging Port is accessible for charging.
• Rotatable Stand allows for hands-free positioning.

5. Maintenance

• ℹ️ Clean this product with a soft, slightly damp cloth.
• ? DO NOT use any abrasive agents to clean the product.
• ? DO NOT attempt to repair/disassemble the light yourself.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling centre, and disposed of in a manner compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE Regulations

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Battery Removal

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd is required to inform potential purchasers of products containing batteries (as defined within these regulations) that they are registered with Valpak's registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.

Notes and Warranty

Note: It is our policy to continually improve products, and as such, we reserve the right to alter data, specifications, and component parts without prior notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.