Sealey 5W & 1W SMD LED Rechargeable Slim Folding Inspection Light & Docking Station Kit

Product Information

Model Numbers: LED1801 & LED1801K

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product, if used according to these instructions and properly maintained, will provide years of trouble-free performance.

Important: Please read these instructions carefully. Note the safe operational requirements, warnings, and cautions. Use the product correctly and with care for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these instructions safe for future use.

1. Safety

1.1. General

• It is important to ensure that the lamp is fully charged before initial use.
• DO NOT turn the lamp on when it is being charged.
• DO NOT shine directly into your, another person's, or an animal's eyes.
• DO NOT allow children to use the lamp.
• DO NOT leave battery in a discharged state. Recharge battery immediately.
• Recharge the battery at least once every six months of non-use.
• There are no user-serviceable components. DO NOT dismantle.
• DO NOT pull the charger plug from the mains socket by the lead.

1.2. Battery Safety

WARNING! To reduce the risk of burns or fire:

• DO NOT attempt to open, disassemble, modify, or service the battery pack.
• DO NOT crush, puncture, short external contacts, or dispose of in fire or water.
• DO NOT expose to temperatures above 60°C (140°F).
• Recycle or dispose of used battery as stipulated by local regulation.
• If the electrolyte in the cells gets on your skin, thoroughly wash with water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

2. Introduction

LED1801:

Slimline foldout inspection light for use in confined spaces, with 6mm minimum thickness. The inspection arm can be rotated 180° and folded back for use as a hands-free inspection light. Features a 5W SMD LED which produces up to 500 lumens, operated by a rolling dimmer switch, and a 1W SMD LED in the end for use as a directional torch. Suitable for hands-free operation with three magnets and a hanging hook. Folds away, small and compact, suitable for keeping in your pocket. Can be charged in a Sealey docking station - LED1801K (not included). Powered by a 3.7V 2.6Ah rechargeable lithium-ion battery which lasts up to 8hr. Supplied with USB charging lead.

LED1801K:

Docking station kit includes 2 x LED1801 and charging station. Each inspection light has a 5W SMD LED (side) + 1W SMD LED (top) producing up to 500 lumens. When both inspection lights are docked, it can be used as a floodlight with two light options (50% and 100%) producing 500 or 1000 lumens. Each inspection light can extend and is able to rotate 180°, making it easy to direct the light. Two charging points with individual LED charging level indicators. Includes 5V~2A mains adaptor and 1m Micro USB charging cable.

3. Specification

4. Operation

4.1. Charging

• The battery fitted to this lamp is considered to be a consumable item and its ability to accept charge will reduce over time. Sealey warrants it against mechanical and electrical defect for a period of one year; this does not cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances, Sealey will not replace the battery even if it is less than one year old.
• The torches will flash when the battery gets low.
• Connect the charger into the charge socket on the lamp (refer to diagram). Plug into power supply and turn on. The red charge LED on the lamp will light as the battery charges. When fully charged, the LED turns green.
• When the battery has fully charged (approx 3hrs), disconnect from mains supply.
• The Lithium battery does not suffer from memory effect and, once fully charged, may be stored for up to six months without another charge.

Figure 1: Diagram showing the Sealey LED1801 inspection light. Key components labeled include: End Torch, Charge Indicator Lights, 0-100% Dimmer Switch For Main Light, End Torch Switch, Magnets, SlimFlex, Micro USB Charging Port, Base magnet and Hook.

Figure 2: Diagram showing the Sealey LED1801K docking station. Key components labeled include: Unit On/Off button and Charge Port.

4.2. Using the Light

• Unfold lamp. Select either directional torch or inspection lamp.
• Brightness is controlled by dimmer switch.
• Lamp can be hung from the hook or attached using magnets.
• When the lamps are docked in the station (LED1801K), you can turn both of the docked torches on by using the On/Off button on top of the unit.

5. Maintenance

• Keep lamp clean and check for damage before every use. If damage is observed, remove from use until the unit is repaired.
• The battery is not designed to be removed.

Parts and Support

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling centre, and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE Regulations

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Battery Removal

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations).

Notes on Policy and Warranty

Note: It is Sealey's policy to continually improve products and as such they reserve the right to alter data, specifications, and component parts without prior notice.

Important: No liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.