SMÅGÖRA Storage Unit

Safety Warning

⚠️WARNING! Children have died from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

The screw(s) and plug(s) supplied can be used with most solid and hollow walls. For solid wood, use the screw(s) without plug(s). Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice.

Read and follow each step of the instructions carefully.

Tools Required for Assembly

The following tools are recommended for assembly:

• ?[Screwdriver - Phillips head]
• ?[Screwdriver - Flat head]
• ✏️[Pencil]
• ?[Spirit Level]
• ?[Hammer]

Parts List

Basic Unit Assembly

Step 1: Prepare Panels

Insert 16x cam lock screws (118331) into the pre-drilled holes on the long panels.

[Diagram Description]: Two long panels laid flat. Hands are shown inserting cam lock screws into holes along the edges. A magnified view shows a cam lock screw being screwed in with a screwdriver.]

Step 2: Attach Side and Base Panels

Attach the side panels to the base panel using 8x dowels (101345) and cam locks (119252). Ensure panels are aligned.

[Diagram Description]: A base panel and two side panels. Hands are shown aligning side panels onto dowels inserted into the base. A magnified view shows a dowel being inserted and a cam lock being tightened with a screwdriver.]

Step 3: Attach Vertical Dividers

Attach the vertical divider panels using 8x dowels (101345) and cam locks (119252).

[Diagram Description]: The partially assembled frame. Hands are shown positioning vertical divider panels and securing them with dowels and cam locks.]

Step 4: Secure Structure

Secure the structure by tightening 8x cam locks (119252).

[Diagram Description]: The unit from the previous step. Hands are shown rotating cam locks with a screwdriver to secure the structure.]

Step 5: Insert Back Panel

Slide the back panel into the grooves on the back edges of the side and divider panels.

[Diagram Description]: The assembled frame. A back panel is shown being slid into grooves on the back edges of the side and divider panels.]

Step 6: Place Shelves

Place the shelves into the unit.

[Diagram Description]: The unit with the back panel attached. Shelves are shown being placed into their designated positions.]

Step 7: Attach Top Panel

Secure the top panel using 8x cam locks (119252).

[Diagram Description]: The unit with shelves in place. The top panel is positioned, and hands are shown tightening cam locks from underneath.]

Wall Mounting

Step 8: Attach Feet

Attach the feet/protectors (122628) to the bottom of the unit using screws. Ensure correct orientation. An incorrect placement is shown crossed out.

[Diagram Description]: The assembled shelf unit. Hands are shown attaching four feet/protectors to the bottom corners. A magnified view shows a foot being screwed into place. An incorrect placement is shown crossed out.]

Step 9: Prepare Wall Brackets

Attach mounting plates (115753) to the wall at the desired height. Use a spirit level to ensure they are straight.

[Diagram Description]: A wall with two mounting plates being attached. A spirit level is shown on top of the plates to ensure they are horizontal.]

Step 10: Attach Unit Brackets

Attach wall brackets (103693) to the unit.

[Diagram Description]: The unit is shown. Hands are shown attaching wall brackets to the top rear edge of the unit.]

Step 11: Secure Unit to Wall

Align the unit with the wall mounting plates and secure it using locking mechanisms (115754).

[Diagram Description]: The unit is shown near the wall. Hands are shown aligning the unit with the wall mounting plates and securing it with locking mechanisms.]

Changing Table Configuration

Step 12: Prepare Changing Table Top

Attach mounting plates (115753) and corner pieces (115754) to the underside of the changing table top.

[Diagram Description]: The changing table top panel. Hands are shown attaching mounting plates and corner pieces to the underside.]

Step 13: Attach Changing Table Top to Unit

Connect the changing table top assembly to the main unit. Use screws and cam locks.

[Diagram Description]: The main unit. The changing table top assembly is shown being lowered onto the unit. Hands are shown securing it with screws and cam locks.]

Step 14: Secure Changing Table Top

Slide the back panel of the changing table top into place. Secure the changing table top to the main unit using cam locks (119252) and screws (118331).

[Diagram Description]: The changing table top is attached. A panel is shown being slid into grooves at the back. Close-up of connection points between the changing table top and main unit, showing hands tightening cam locks.]

Step 15: Attach Pad Supports

Attach the pad supports to the changing table top. Use screws with a maximum length of 25mm (1 inch). An incorrect method is shown crossed out.

[Diagram Description]: The changing table top. Hands are shown attaching pad supports. A magnified view shows a screw being used, with a note on maximum screw length (10mm / 2/4"). An incorrect method is crossed out.]

Step 16: Final Assembly

Insert the final shelf into the changing table configuration. Secure the changing table top using locking mechanisms (103693, 115754).

[Diagram Description]: The changing table unit. A shelf is shown being inserted. Close-up of connection points showing hands securing the unit with locking mechanisms.]