Ecler PAGENETDN Digital Panel User Manual

1. Important Warnings

Warning Symbols:

• Lightning Bolt in Triangle: Alerts users to the presence of dangerous, uninsulated voltages within the apparatus that may pose a risk of electric shock.
• Exclamation Mark in Triangle: Alerts users to important operating and maintenance instructions accompanying the product.

Specific Warnings:

• Terminals marked with a lightning bolt symbol may carry sufficient magnitude to constitute an electric shock hazard. External wiring must be installed by qualified personnel or use pre-made cables.
• To prevent electric shock or fire hazards, do not expose the equipment to rain or moisture.
• Class I construction apparatus must be connected via a grounded plug.

2. Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat, including amplifiers.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades, one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wider blade or the third prong are for your safety. If the provided plug does not fit into your outlet, consult an electrician to replace the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods.
13. For servicing, contact qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. Disconnecting from the mains: turning off the POWER switch will stop all functions and indicators of the amplifier, but complete disconnection is achieved by unplugging the power cord from its connector. Therefore, it should always be easily accessible.
15. The equipment connects to a grounded outlet via the power cord.
16. Part of the product labeling is located on the bottom of the unit.
17. This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
18. This product is for indoor use only.

Disposal Warning: This product must not be disposed of as unsorted municipal waste. Please take it to the nearest electrical and electronic waste treatment center.

NEEC AUDIO BARCELONA, S.L. disclaims any responsibility for damages that may be caused to persons, animals, or objects due to non-compliance with the above warnings.

3. Important Note

Thank you for choosing the EclerNet DANTE™/AES67 PAGENETDN paging station. For maximum operability and performance, it is VERY IMPORTANT to read and understand the considerations in this manual before connection.

For optimal performance, maintenance should be carried out by authorized Ecler Technical Services. All ECLER products have a warranty; please consult www.ecler.com or the warranty card for validity and conditions.

4. Introduction

The PAGENETDN is a programmable paging console with dual audio output: DANTE™/AES67 (digital) and analog (balanced). It allows control and microphone signals to work with any EclerNet digital matrix, including those that support DANTE™/AES67 or not, such as MIMO4040DN, MIMO88, MIMO88SG, and MIMO1212SG.

It shares control functions with the WPNETTOUCH and can be programmed to control one or more networked EclerNet devices, or even an entire installation comprising various EclerNet devices like MIMO matrices, NXA series digital audio managers, DUO-NET PLAYER units, etc. All programming is done via the EclerNet Manager application.

The device features a desktop console design with a 10” capacitive touchscreen, a gooseneck microphone, and user control panels for paging and controlling networked EclerNet devices, VEO video devices, and third-party devices.

4.1. Main Features

• Integrated digital control panel with a touchscreen, similar to the WPNETTOUCH device.
• 10.1” IPS display (1280 x 800 pixels), capacitive, multi-touch panel.
• Compatible with PoE (Power over Ethernet) power supply.
• Compatible with external power supply (12 VDC, 2A) with multi-plug AC adapters.
• Ethernet Base-Tx 10/100Mb interface.
• Included flexible gooseneck microphone with XLR connector and security latch.
• Audio transport via DANTE™/AES67, 2 channels: Channel #1 for microphone signal, Channel #2 for AUX input signal.
• Phantom power available for the MIC input.
• Analog balanced MIC output, compatible with devices not supporting DANTE™/AES67 natively (e.g., MIMO88, MIMO88SG, MIMO1212SG).
• Stereo AUX LINE input with RCA connectors. Input signal is converted to mono and sent over the network via DANTE™/AES67 channel #2. Can be used for external audio sources.
• Paging functions based on programmable UCP control panels.
• EclerNet control device, capable of executing EclerNet projects internally, acting as a server and/or client for UCP panels.

5. Installation and Connections

5.1. Installation and Wiring

The unit comes with the microphone detached and must be inserted into the console before use. To install the microphone, align the connection pins with the XLR connector on the console and apply pressure until it clicks. The security tab ensures proper seating. A slight vertical oscillation indicates correct installation, minimizing handling noise.

To remove the microphone, use a pin-type extraction tool to press the release hole on the back of the microphone base. This will release the XLR security tab, allowing the microphone to be pulled out firmly.

Before programming and use, the PAGENETDN must be connected to the network via its internal RJ45 ETHERNET interface. This and other connectors are accessible by removing the bottom metal plate (requires removing 3 screws).

Internal View of PAGENETDN (after removing bottom plate):

• EXTERNAL PSU CONNECTOR
• ETHERNET INTERFACE
• PHANTOM POWER ON/OFF
• MIC IN GAIN
• LINE GAIN
• AUX IN
• MIC IN
• HPF Off/On
• ANALOGUE AUDIO OUT

The unit can be powered by DC, directly via PoE (Power over Ethernet) from the connected Ethernet switch, or via the included 12 VDC, 2A external power supply (EXTERNAL PSU CONNECTOR).

Additional Audio Connectors:

• AUX IN (L/R): Stereo LINE input with RCA connectors. The input signal is converted to mono and sent to the network via DANTE™/AES67 channel #2. It can be used for external audio sources.
• MIC OUT (ANALOGUE AUDIO OUT): Balanced mono output (Euroblock). This is a copy of the microphone signal in analog format, useful for paging systems with devices that do not support DANTE™/AES67.

5.2. Audio Adjustments

The PAGENETDN offers several audio controls for adjusting incoming analog audio signals:

• PHANTOM POWER ON/OFF (default = ON): Activates or deactivates phantom power to the microphone's XLR connector. This is used for condenser microphones, such as the included Ecler eMCN1.
• HPF (High Pass Filter) ON/OFF (default = ON): Activates or deactivates a high-pass filter (100Hz @ 12dB/oct) applied to the microphone's audio signal. This helps minimize low frequencies and unwanted noise.
• MIC IN GAIN (*): Adjusts the preamp gain for the incoming microphone signal. This affects both the DANTE™/AES67 channel #1 output and the ANALOGUE AUDIO (MIC) OUT.
• AUX IN GAIN (LINE GAIN): Adjusts the preamp gain for the incoming AUX IN ST LINE signal, which is then converted to mono and sent to DANTE™/AES67 channel #2.

(*) Note: The microphone's XLR connector supports standard XLR microphones, including the Ecler eMCN1 supplied with the unit. However, it may not securely hold microphones with a wider base than the standard XLR size.

Image Description: Two microphones are shown. One is the Ecler eMCN1. The other, marked with a red 'X', appears to be a microphone with a wider base that does not fit the standard XLR connector.

6. Operation

The PAGENETDN must be correctly included in an EclerNet project and configured (considering DANTE™/AES67 audio and control routing) to display the UCP paging and control panels for the end-user. Examples are provided:

MIMO4040DN MAIN PAGER: A visual representation of a paging interface with 40 programmable buttons, labeled 1 through 40, with 'ALL', 'PAGE', and 'CLEAR' buttons at the bottom.

SECONDARY PAGER: A visual representation of a secondary paging interface with 16 programmable buttons, labeled 1 through 16, with 'ALL', 'PAGE', and 'CLEAR' buttons at the bottom.

Image Description: A screenshot showing a dressing room with a control panel labeled 'VOLUME' and 'Radios' with buttons 1, 2, 3, 4, ePLAYER1, PC 1 WIN, PC 2 MAC, and a MUTE button. The volume slider ranges from 0 to 10.

For more information, please consult the EclerNet Manager application user manual, chapter DISPOSITIVO PAGENETDN.

7. Local Unit Configuration

The PAGENETDN's settings and configuration menus can be accessed locally via its touchscreen. These menus are identical to those available for the WPNETTOUCH device, as the PAGENETDN incorporates a WPNETTOUCH unit.

The same configurations are accessible remotely when the unit is controlled by a remote computer running the EclerNet Manager application.

Local access to configuration menus is achieved by tapping the SETUP icon on the unit's home page.

Image Description: The screen shows 'User Control Panels' connected to 'SCREEN (192.168.0.100)'. It displays four panels: 'UDP/TCP Control', 'M4040DN Paging', 'Paging consoles', and 'CONF_ROOM', each with resolution details. Below this, there is a navigation bar with left/right arrows and an Ecler logo.

The available configuration menus are:

• Screen Configuration
• Device Configuration
• Network Configuration
• Information/Tools

7.1. Screen Configuration Menu

This menu allows configuring display elements and controls:

• Display Mode: Controls screen dimming behavior during idle periods (10 seconds of inactivity). Modes: ON (always lit), DIMMED, OFF (off).
• Backlight Intensity: Adjusts screen brightness when not in idle mode.
• Auto-Zoom Panels: When activated, graphical control panels (UCPs) automatically resize to fit the visible area, regardless of their original resolution in the EclerNet Manager project file.
• Show Panel OSD Buttons: Toggles the display of navigation buttons in the corners of the UCPs. Upper corner buttons allow horizontal panel scrolling (left/right), and lower corner buttons access the icon bar.

Image Description: The screen shows 'Setup | Screen Configuration' with options for 'Display Mode' (ON, DIMMED, OFF), 'Backlight Intensity' (slider from 0 to 100), 'Auto-Zoom Panels' (YES/NO toggle), 'Show Panel OSD Buttons' (YES/NO toggle), and 'Scroll by OSD Buttons' (YES/NO toggle), 'Scroll by Swipe' (YES/NO toggle).

Note: Even when OSD buttons are hidden, they can remain active. Pressing the upper corners scrolls through panel pages, and the lower corners access the icon bar. This should be considered when designing UCP layouts, ensuring corners are clear if these OSD buttons are to be used.

• Scroll by OSD Buttons: Toggles the page scrolling action via the upper corner buttons, even when OSD buttons are hidden.
• Scroll by Swipe: Toggles page scrolling via a left or right swipe gesture on the screen.

Image Description: The bottom of the screen displays an icon bar with left/right arrows for horizontal scrolling, a 'HOME' icon for the main page, and an 'X' icon to exit the bar. It also shows 'GYM' and 'Page 2 of 6'.

7.2. Device Configuration Menu

This menu allows adjusting the following unit parameters:

• Device Name: The name of the device, visible to other WPNETTOUCH/WPmSCREEN devices and the EclerNet Manager application.
• Device Password: A password to protect the device from configuration changes. It requires a non-empty password to be set.
• Enable UCP Server: Activates/deactivates the unit's built-in UCP server.
  • Enabled: The EclerNet project saved on the unit ('Local Project') becomes fully functional, controlling included hardware devices (MIMO4040DN, MIMO88, NXA units, etc.) and serving UCPs to network clients.
  • Disabled: The EclerNet Local Project is deactivated, releasing control of all included hardware. This also stops serving UCPs to clients. Note: When disabled, another device or computer running a project with existing hardware from the WPNETTOUCH Local Project may take control. Only one device/project can control the same hardware at a time. Controlled units must be released before attempting control from another device.

Image Description: The screen shows 'Setup | Device Configuration' with fields for 'Device Name' (editable text field), 'Device Password' (editable text field with 'Change...' button), and 'Enable UCP Server' (YES/NO toggle). Below is a QWERTY keyboard layout.

From EclerNet Manager, you can release devices controlled by the computer by creating a new project (File -> New project) or by disconnecting them one by one (right-click -> Disconnect).

From a WPNETTOUCH/WPmSCREEN, you can release devices controlled by the unit by setting the 'Enable UCP Server' option to NO.

7.3. Network Configuration Menu

This menu allows modifying the unit's network connection parameters: IP Address, Network Mask, and Gateway.

Note: Neither the WPNETTOUCH nor any other EclerNet device supports dynamic IP address assignment (DHCP). Static IP addresses must always be assigned manually.

Image Description: The screen shows 'Setup | Network Configuration' with fields for 'IP Address', 'Network Mask', and 'Gateway', each with an editable text field and a 'X' button to clear. Below is a numeric keypad and arrow keys.

7.3.1 Factory Default Network Parameters

The factory default network parameters for EclerNet Manager compatible devices are:

• IP: 192.168.0.100
• Mask: 255.255.255.0
• Gate: 192.168.0.1
• UDP Port: 2210

7.4. Information / Tools Menu

This menu displays the following information:

• Server IP Address: The IP address of the UCP server the unit is connected to as a UCP client. If the unit is connected to itself as a client, it will show its own IP address (=Local IP Address).
• Server Project: The name of the project running on the server the unit is connected to as a UCP client (project running on the client's UCP server).
• Local IP Address: The IP address configured for the WPNETTOUCH unit.
• Local Project: The name of the project saved in the WPNETTOUCH unit's internal storage. This project can be loaded onto the unit using the EclerNet Manager software.
• Available Storage: Internal storage space available for loading a project file, which includes user control panel data and graphics.
• Ethernet Address: The MAC address of the network interface card (NIC) installed in the WPNETTOUCH unit.
• Display Resolution: The native resolution of the unit's IPS panel (1280 x 800).
• Firmware version: Shown in the bottom right corner (e.g., v0.04r11).

Image Description: The screen shows 'Setup | Information/Tools' with fields displaying 'Server IP Address', 'Server Project', 'Local IP Address', 'Local Project', 'Available Storage', 'Ethernet Address', and 'Display Resolution'. Buttons for 'Project Defaults', 'Factory Defaults', and 'Reboot' are also present. The Ecler logo and product information 'PAGENETDN v0.04r11' are displayed.

Restore / Reboot Options:

• Project Defaults: Clears the current project, replacing it with a blank one. This action is irreversible after confirmation.
• Factory Defaults: Clears all unit configuration and data, restoring factory default settings. This action is irreversible after confirmation.
• Reboot: Restarts the unit. Network connection will be temporarily lost, and normal performance will resume after reboot.

Image Description: Three sections are shown, each with a question mark icon and a title: 'Project Defaults', 'Factory Defaults', and 'Reboot'. Each section includes a warning message and 'Ok' and 'Cancel' buttons.

8. Connecting to a UCP Server

From the unit's home screen, tapping the connection icon at the top provides access to the connection page.

Image Description: The screen displays 'User Control Panels' connected to 'SCREEN (192.168.0.100)' with four UCP panels. Below this, a 'Connect to...' screen is shown, prompting for a 'Server Address' and a 'Connect' button, with a numeric keypad.

This page allows selecting the UCP server to which the unit will connect as a client. The UCP server can be a computer, a MIMO404040DN matrix (which has an integrated UCP server), another WPNETTOUCH/WPmSCREEN unit, or even the PAGENETDN/WPNETTOUCH unit itself. In any case, the UCP server will host and run an EclerNet Manager project that includes a series of UCPs manageable remotely by any UCP client.

You can directly enter the server device's IP address using the on-screen keyboard, or select a device from a list of automatically detected server devices by clicking the grey button with a list icon to the right of the 'Connect' button.

Image Description: The screen shows 'Connect to... | Server list' with a list of detected UCP servers: 'SCREEN', 'DLOZA-HP', and 'ISE4040DN', each with an IP address. Up and down arrows are present for scrolling.

Note: In the list of detected server devices, the name of the WPNETTOUCH unit under control will appear in green (matching the local IP address).

After selecting a server unit or an IP address using either method, clicking the 'Connect' button confirms the selection and initiates the connection process. If successful, the UCPs provided by the server will appear on the screen.

Image Description: The screen shows 'User Control Panels' connected to 'DLOZA-HP (192.168.0.50)' with four UCP panels displayed.

9. Package Contents

• PAGENETDN Unit
• Gooseneck microphone + anti-pop filter
• External power supply, 24V – 12A universal, AC multi-plug
• Euroblock 3p aerial connectors
• Quick user guide and warranty card

10. Function List

1. Multi-touch screen
2. Gooseneck microphone
3. XLR connector
4. Power cable connector

11. Function Diagram

Diagram Description: Two views of the PAGENETDN unit are shown. The top view highlights the screen (1), the gooseneck microphone (2), and the XLR connector (3). The bottom view shows the rear of the unit, highlighting the microphone (2), the XLR connector (3), and the power cable connector (4).

12. Block Diagram

Diagram Description: A block diagram illustrates the PAGENETDN's internal structure. It shows inputs for MIC and LINE signals, with gain and HPF controls. These signals are processed and sent to the DANTE SYSTEM-TX. A 10.1" TOUCHSCREEN (1280px x 800px) is connected to the system. Power is supplied via EXTERNAL POWER or ETHERNET WITH P.O.E., managed by a POWER SUPPLY INTERFACE and PCB SWITCH.

13. Technical Specifications

MIC INPUT

• Microphone type: Removable gooseneck condenser microphone (eMCN1)
• Polar pattern: Unidirectional
• Microphone freq. response: 50Hz – 18kHz (-10dB)
• Phantom Voltage: 48VDC, ON/OFF by internal JUMPER
• Output level with eMCN1 MICROPHONE: -5dBV @ 94dB SPL with ADJ MAX; -10dBV @ 94dB SPL with ADJ MID; -20dBV @ 94dB SPL with ADJ MIN.
• HPF: 100Hz 12dB/oct ON/OFF by internal JUMPER

LINE INPUT

• Connector: RCA
• Signal: Line level L + R
• Nominal input level: -10dBV
• Gain adjust: -20dBV / 0dBV
• Input impedance: >10kΩ

DANTE™/AES67 AUDIO INTERFACE

• DANTE™/AES67 Network Tx channels: 2 (2 flows)
• Latency: 1 / 2 / 5 ms (selectable)
• Connector: RJ45

AUDIO OUTPUTS

• Microphone output signal Connector: Balanced, analog
• Output level: Phoenix connector (symmetric)
• 0dBV

System

• CPU: RK3128 quad core processor, clocked 1.6G
• RAM: 1GB
• ROM: 8GB

Screen

• Size: 10.1" IPS
• Resolution: 1280x800
• Contrast ratio: 1300:1
• Brightness: 300cd/m²
• Screen scale / Display area: 16:9 / 218x135mm
• Backlight: LED
• Touch-panel: Capacitive multi-touch

Network & Connectivity

• Ethernet: Supports PoE
• Ethernet port: Ethernet Base-Tx 10/100Mb / 1GB CAT5e or better up to 100m.

Power

• External power supply voltage: 12VDC
• Maximum power consumption: 12W (from 12V External Power Supply), 15W (from PoE)
• PoE: class 0 802.3af Poe PD compliant
• Mains Voltage: 100-240VAC + External PSU 12VDC

General

• Dimensions (microphone excluded): 295x155x135 mm / 11.6"x6.1"x5.3" (WxHxD)
• Weight: 1.5 kg / 3.3 lbs
• AC Power Adapter: 100-240VAC 47-63Hz 12V / 2A
• Accessories included: AC power adapter (100-240VAC 47-63Hz 12V / 1.5A, multiplug), Microphone (Ecler eMCN1)

Product Information

All product characteristics are subject to variation due to production tolerances. NEEC AUDIO BARCELONA S.L. reserves the right to make design or manufacturing changes or improvements that may affect the specifications of this product.

For technical inquiries, please contact your supplier, distributor, or complete the contact form on our website under Support / Technical Consultation.

Motors, 166-168 08038 Barcelona - España - (+34) 932238403 | information@ecler.com | www.ecler.com