HOMCOM 83A-048V80 Bar Table and Stools Set Assembly Instructions
Model: 83A-048V80
Estimated Assembly Time: ⏱️ 30 MIN
Recommended Persons: ??? 2+
Total Steps: 6️⃣ STEPS
Important Information
IMPORTANT: RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Instructions for use:
- Place the furniture stably on a flat floor.
- Stay away from open flames or heat sources.
- Avoid overloading the furniture.
Precautions before assembly:
- Prepare a clean and dry mounting area.
- Verify that the product is not damaged.
- Check that none of the pieces are missing.
Maintenance:
- Clean with a soft fabric.
- Check the furniture regularly.
Storage conditions:
- Store the product in a clean and dry environment to avoid mold.
Caution: Beware of crushing and cutting hazards during assembly. The manufacturer declines all responsibility for damages due to improper installation or weather conditions.
Parts List
| Part No. | Description | Quantity |
|---|---|---|
| 1 | Side Frame | x2 |
| 2 | Long Crossbar | x2 |
| 3 | Short Crossbar | x1 |
| 4 | Tabletop | x1 |
| 5 | Stool Seat | x2 |
| 6 | Stool Leg Frame | x4 |
| 7 | Stool Cross Brace | x4 |
| 8 | Stool Cross Brace | x4 |
| 9 | Stool Cross Brace | x4 |
Hardware List
| Label | Description | Quantity |
|---|---|---|
| A | M6*12 Screw (+1 spare) | x16 |
| B | M6*20 Screw (+1 spare) | x16 |
| C | M6*30 Screw (+1 spare) | x8 |
| D | M6*40 Screw (+1 spare) | x16 |
| E | M6*50 Screw (+1 spare) | x6 |
| F | M8 Screw | x4 |
| G | M6 Screw | x4 |
| H | Allen Key | x1 |
Assembly Steps
Step 1: Assemble Table Base Frames
Take two Part 1 (Side Frames). Attach one Part 3 (Short Crossbar) between the lower sections of the side frames using four Part F (M8 Screws). This creates the base for one side of the table. Repeat for the second side.
Step 2: Attach Table Crossbars
Take the two assembled side frames. Attach two Part 2 (Long Crossbars) to the upper sections of the side frames, one at the front and one at the back. Use four Part D (M6*40 Screws) for each crossbar, totaling eight screws. This forms the main table frame.
Step 3: Attach Tabletop
Place Part 4 (Tabletop) onto the assembled table frame. Secure it from underneath using sixteen Part A (M6*12 Screws) and four Part G (M6 Screws) through the pre-drilled holes in the frame and tabletop.
Step 4: Assemble Stool Leg Frames
For each stool, take two Part 6 (Stool Leg Frames). Attach the three sets of cross braces (Part 7, Part 8, Part 9) between the leg frames. Use a total of six Part E (M6*50 Screws) per stool to secure these braces.
Step 5: Attach Stool Seats
Place Part 5 (Stool Seat) onto the assembled stool frame. Secure it from underneath using eight Part B (M6*20 Screws) and eight Part D (M6*40 Screws).
Step 6: Final Tightening and Adjustment
Reinforce the stool seat attachment using eight Part C (M6*30 Screws). Stand the assembled stools upright and adjust the angle of the legs if necessary before gradually tightening all screws. Periodically check all fittings and re-tighten as needed.
Final Check
Ensure all parts are securely fastened and the furniture is stable. The assembly is now complete.
