Safavieh Nightstand Assembly Instructions
? NOTICE
*Please make sure that you have all parts indicated and they are in good condition before you begin assembly of this item. Refer to the part list and hardware list below for guidance.
*This item should be assembled on a soft surface to prevent scratching the finish during assembly.
*This item may require periodic tightening.
*If you are having difficulty, our friendly Customer Care team is always here to help.
⚙️ PREPARATION
*Before beginning assembly of product, make sure all parts are present. Compare parts with the part contents list and hardware contents list.
*If any part is missing or damaged, do not attempt to assemble the product.
*Estimated Assembly Time: 60 minutes.
*Tools Required for Assembly (included): Allen Key ?
*If you are having difficulty, our friendly Customer Care team is always here to help. Please email customersupport@safavieh.com
? CARE AND MAINTENANCE
Always use felt pads under all articles to prevent discoloration or softening of the lacquer. Plastic and rubber bases on items can discolor wood. Wipe up spills immediately and avoid common hazards such as hot dishes, harsh solvents, and abrasives. Cleaning should be done with a soft lint-free cotton cloth dampened with water or furniture polish. On highly used surfaces, we recommend applying a quality paste wax which should be used on a regular basis to provide additional protection from scratches and spills. How often you apply the wax depends on how much wear the furniture receives.
Product Information
Product Dimensions: 22.13" W x 15.67" D x 22.80" H
⚠️ WARNING :
WEIGHT CAPACITY: 26.4 LBS.
DRAWER LOAD CAPACITY 22 LBS
Warning: Do not stand on chest.
Warning: Do not over torque bolts.
Diagram shows a two-drawer nightstand/chest with a slatted front, a top surface, and four metal legs.
Part List
| Piece | Description | Qty |
|---|---|---|
| A | Top Board | 1 |
| B | Bottom Board | 1 |
| C | Side Board Left | 1 |
| D | Side Board Right | 1 |
| E | Front Drawer | 2 |
| F | Side Drawer Left | 2 |
| G | Side Drawer Right | 2 |
| H | Back Drawer | 2 |
| I | Bottom Drawer | 2 |
| J | Back Board | 1 |
Diagram shows an exploded view of the furniture parts labeled A through J, with quantities indicated. Part E, F, G, H, I are shown in multiples.
Hardware List
| Piece | Description | Qty |
|---|---|---|
| HW1 | Cambolt | 12 |
| HW2 | CamLock Big | 4 |
| HW3 | Dowel Big | 8 |
| HW4 | Dowel Small | 4 |
| HW5 | Screw M 7 x 50 mm | 4 |
| HW6 | Allen Key | 1 |
| HW7 | CamLock Small | 8 |
| HW8 | Screw M 8 x 39 mm | 8 |
| HW9 | Screw M 6 x 10.5 mm | 8 |
| HW10 | Screw M 3.5 x 13 mm | 12 |
| HW11 | Handle | 2 |
| HW12 | Screw M 4 x 22 mm | 4 |
| HW13 | Corner Brace | 4 |
| HW14 | Support Corner Brace | 4 |
| HW15 | Support Metal Leg 1 | 2 |
| HW16 | Support Metal Leg 2 | 2 |
| HW17 | Screw M 6 x 35 mm | 4 |
| HW18 | Screw M 6.4 x 35 mm | 10 |
| HW19 | Wedge | 14 |
| HW20 | Screw M 3.5 x 15.5 mm | 14 |
| HW21 | Metal Square Leg | 4 |
| HW RM35A | Rail | 2 |
Diagrams show visual representations of each hardware item (screws, bolts, cam locks, dowels, handles, legs, braces, rails) with their corresponding codes and dimensions.
Assembly Instructions
STEP 1: Prepare Drawers
Insert Cambolt (HW1) into Front Drawer (E). Insert Dowel Small (HW4) into Side Drawers (F & G).
Diagram shows inserting a cambolt into part E and dowels into parts F and G. Quantities of parts and hardware are indicated (e.g., x 2).
STEP 2: Assemble Drawer Box
Combine Side Drawers (F & G) into Front Drawer (E), then tighten camlock (HW7) using a screwdriver ?. Insert Bottom Drawer (I) with laminated face facing upward, then attach Back Drawer (H) and secure with Screw M8x39mm (HW8).
Diagram shows connecting drawer sides to the front, tightening camlocks, inserting the bottom panel, and attaching the back panel with screws.
STEP 3: Attach Handles and Runners
Use Screw M4x22mm (HW12) to attach Handle (HW11) to the Front Drawer. Install the metal runner (HW RM35A) into position as shown in the diagram. Secure with screws M3.5x13mm (HW10).
Diagram shows attaching a handle to the drawer front and installing a drawer runner mechanism.
STEP 4: Secure Drawer Bottom
Insert Screw M3.5x15.5mm (HW20) and wedge (HW19) into the bottom of the drawer according to the diagram.
Diagram shows inserting screws and wedges into the underside of the drawer to secure the bottom panel.
STEP 5: Prepare Top and Side Boards
Insert Cambolt (HW1) into Top Board (A), and insert Dowel Big (HW3) into Side Board Left (C) and Side Board Right (D). Continue by securing part of the metal runner (HW RM35A) into position as shown in the diagram, using screw M6x10.5mm (HW9).
Diagram shows inserting cambolts into the top board, dowels into side boards, and attaching drawer runners to the side boards.
STEP 6: Attach Side Boards to Top
Attach Side Board Left (C) and Side Board Right (D) to Top Board (A). Secure with Camlock Big (HW2) and tighten using a screwdriver ?.
Diagram shows connecting the side panels to the top panel and securing them with camlocks.
STEP 7: Attach Back and Bottom Boards
Attach Back Board (J) and insert Bottom Board (B). Secure with Screw M7x50mm (HW5), and tighten screws using Allen Key (HW6) ?.
Diagram shows attaching the back panel and inserting the bottom panel into the main frame, secured with screws.
STEP 8: Install Corner Braces and Legs
Insert Support Corner Brace (HW14) into the tube of Leg (HW21). Then, insert Screw (HW17) into the hole of Corner Brace (HW13) which is attached to the leg. Screw in slightly just enough to grip the Leg (HW21) with the Support Corner Brace (HW14) inside. Do not tighten fully. Arrange Support Metal Leg 1 (HW15) & Support Metal Leg 2 (HW16) on the floor as per the image.
Diagram shows how to attach corner braces to the legs and then prepare to attach the legs to the main furniture body. It also shows arranging the legs on the floor.
STEP 9: Attach Prepared Legs
Install the prepared Leg (HW21) which has the Corner Brace (HW13) attached. Ensure the Corner Brace (HW13) hooks onto the designated hole on the Support Metal Leg (HW15) and (HW16). Screw in just enough to grip the support using Allen Key (HW6) ?. Do not fully tighten. Repeat for the other legs.
Diagram shows attaching the legs, which have corner braces, to the underside of the furniture frame. Partial tightening is indicated.
STEP 10: Secure Leg Unit
Install the assembled leg unit from Step 9 onto the main assembled unit by inserting Screw (HW18). Tighten with Allen Key (HW6) ?. Then tighten all the screws on the assembled leg unit.
Diagram shows attaching the entire leg assembly to the main furniture body and then fully tightening all screws.
STEP 11: Secure Back Panel
Use Wedge (HW19) and Screw M 3.5x15.5 (HW20) to tighten the back of the nightstand using a screwdriver ?. Please align the top board and bottom board in a 90° position against the side board, before securing the wedges (HW19).
Diagram shows securing the back panel of the nightstand using wedges and screws, ensuring right angles.
STEP 12: Insert Drawers
Hold the sides of the drawer, position the wheel of the rail at the drawer back and the wheel of the rail at the side boards, according to the image. Slide in the drawers one by one into the nightstand. Place your furniture on a level floor. The legs come with an adjustable leveller; adjust it as needed until your furniture sits steady on the floor.
Diagram shows how to align the drawer runners and slide the assembled drawers into the nightstand. It also illustrates the adjustable leg leveler.
STEP 13: Assembly Complete
Assembly is complete. ✔️
Diagram shows the fully assembled nightstand/chest.
TIPPING RESTRAINTS KIT INSTALLATION GUIDANCE
Different wall materials require unique wall fasteners. The wall plugs (AA2) and screws (AA3) are designed for fixing to concrete walls only. Please consult your local hardware store to ensure you are using the correct hardware for your wall type.
Diagram shows the components of the tipping restraint kit: strap (AA1), wall plugs (AA2), screws (AA3), and furniture screws (AA4).
- Attach the bracket (AA1) to the furniture approximately 8-10cm from the top using screw (AA4).
- Mark the wall and drill a hole for the wall plug (AA2).
- Insert the wall plug (AA2) into the wall.
- Attach the strap (AA1) to the wall using screw (AA3) and wall plug (AA2).
- Connect the strap to the furniture bracket.
Diagrams illustrate the steps: attaching the bracket to furniture, drilling into the wall, inserting wall plug, attaching strap to wall, and connecting strap to furniture.
