Safavieh DCH3300 Chair
Item ID: DCH3300
Item Dimensions: W17.7”x D18.1”x H36.4”x H18"
Notice
Please make sure that you have all parts indicated and they are in good condition before you begin assembly of this item. Refer to the part list and hardware list for guidance.
This item should be assembled on a soft surface to prevent scratching the finish during assembly.
This item may require periodic tightening.
If you are having difficulty, please contact Safavieh Customer Care by emailing customersupport@safavieh.com.
Preparation
- Before beginning assembly, make sure all parts are present. Compare parts with the part contents list and hardware contents list.
- If any part is missing or damaged, do not attempt to assemble the product.
- Estimated Assembly Time: 10 minutes.
- Tools Required for Assembly (included): Allen Key.
Care and Maintenance
Wood Care
Adhesive felt pads should always be applied to areas of furniture which make direct contact with flooring; this application will prevent damage to the furniture and/or surfaces on which the furniture rests. Objects placed on furniture should rest on non-abrasive material to prevent damage to the wood finish. Objects composed of plastic and rubber are known to discolor and damage wood surfaces. Wipe up spills immediately and avoid common hazards such as hot dishes, harsh solvents, and abrasives. Cleaning should be done with a soft, lint-free cotton cloth dampened with water or furniture polish. On highly used surfaces, applying a quality paste wax regularly is recommended to provide additional protection from scratches and spills. The frequency of wax application depends on the wear the furniture receives.
Part List and Hardware List
| Piece | Description | Picture Description | Quantity | Piece | Description | Picture Description | Quantity |
|---|---|---|---|---|---|---|---|
| A | Chair Back With Seat | [Image of a chair back with a seat attached] | 1X | HW3 | Spring Washer M6 | [Image of a spring washer] | 6X |
| B | Left Leg Frame (FL) | [Image of a single left leg frame component] | 1X | HW4 | Flat Washer M6 | [Image of a flat washer] | 6X |
| C | Right Leg Frame (FR) | [Image of a single right leg frame component] | 1X | HW5 | Barrel Nut | [Image of a barrel nut] | 2X |
| D | Strecher | [Image of a long, thin bar (stretcher)] | 1X | HW6 | Felt Pad | [Image of a square felt pad] | 4X |
| HW1 | JCBCW x 40mm | [Image of a screw] | 6X | HW7 | Wood Button | [Image of a small wooden cap or plug] | 2X |
| HW2 | JCBC M6 x 50mm | [Image of a bolt] | 2X | HW8 | Allen Key M4 x 110mm | [Image of an L-shaped Allen key] | 1X |
Assembly Instructions
Step 1: Insert Barrel Nut and Stretcher
Insert Barrel Nut (HW5) into the hole on Stretcher (D). Then insert the JCBC bolt (HW2) and finally place the Wood Button (HW7).
[Diagram illustrating the assembly of the stretcher (D) with barrel nut (HW5) and bolt (HW2), followed by a wood button (HW7)]
Step 2: Attach Leg Frames to Seat
Insert JCBCW (HW1) to attach the Right Leg Frame (C) and the Left Leg Frame (B) to the Seat (A).
[Diagram showing leg frames (B, C) being attached to the seat (A) using screws (HW1)]
Step 3: Apply Felt Pads
Put Felt Pad (HW6) on top of each leg.
[Diagram depicting felt pads (HW6) being placed on the top ends of the leg frames]
Step 4: Final Tightening
Place the chair upright. Ensure all legs are level. Firmly tighten all bolts with the Allen Key (HW8) while the chair is upright.
[Diagram of the fully assembled chair, with an emphasis on ensuring legs are level and tightening bolts with the Allen key (HW8)]
Safety Warnings
Weight Capacity: 225lbs
Warning: Do not stand on chair.
Warning: Do not over torque bolts.
mailto:customersupport@safavieh.com
