Enbrighten Mini LED Color Changing Landscape Lights

Best Practices for Installation

• Install power supply/receiver a minimum of 18" above the ground to ensure optimal range on remote control.
• Note that placing power supply/receiver directly on ground can severely diminish the remote control range.
• Do not mount power supply/receiver behind large objects such as posts, walls, large boulders or other items which may interfere with the signal from the remote control. Also, avoid mounting the power supply/receiver on or near metal walls or other large metal objects. Doing so can reduce the remote control's operation distance.

Congratulations

Congratulations on your recent purchase of Enbrighten Mini Landscape Lights. Enbrighten Mini Landscape Lights are designed to provide lighting for life.

IMPORTANT: Before installation, please read all the warning statements included at the bottom of these instructions.

To ensure proper installation, please follow each step below.

Initial Setup

1. Carefully unpack Enbrighten Mini Landscape Lights from box. Remove and dispose of the wire ties and plastic bag (see warning on bottom).
2. Locate remote control and install 2 AAA batteries (included).
3. When installing landscape lights outside, a ground-fault circuit interrupter (GFCI) receptacle must be used. Before installing, plug the landscape lights into the GFCI receptacle to ensure all lights work properly.

IMPORTANT: Unplug the landscape lights prior to installation.

Installing Landscape Lights

Each landscape light is designed for mounting with the included stakes (one per light) or for use on a flat surface (see below instructions).

Ground Installation

1. Carefully plan your installation by laying out the landscape lighting system. Start with the GFCI receptacle and mounting of controller. Placement for the first light can be up to 20' away from the controller. Each subsequent light can be placed up to 2' from the previous light.
2. Mount the controller within an appropriate distance for the polarized plug to reach the receptacle. The controller can be mounted using the keyholes on the rear of the controller or the keyhole ear tabs (see figure A). For optimal remote range, be sure to mount at least 18" off the ground. Do not lay the controller directly on the ground or where standing water may accumulate (see figure B). Laying controller on the ground will significantly reduce remote range.

Figure A: Illustrates the controller's keyhole mounting feature and dimensions (2in./5cm).

Figure B: Depicts the controller placement, emphasizing avoiding direct ground contact or areas with standing water to maintain remote range.

Ground Mounting Details

• Place light directly on ground or garden bedding.
• Using provided mount stake: Insert the stake into the bottom keyhole, ensuring it locks into place. The stake can then be inserted into the soil or mulch. If the ground is too hard, loosen soil or remove obstacles.

Cord Management: Your Enbrighten Mini Landscape Lights feature burial-grade cable, allowing you to conceal excess cable by burying it in the soil or covering it with garden bedding.

Flat-Surface Mounting

Lay out the landscape system as planned. Mount lights to a solid support structure (e.g., joist, beams, studs). Use one #6 pan head screw (not included) of appropriate length for the mounting surface.

Note on Cords: Do not pull cords tight, as it may damage electrical connections. Leave a small amount of slack on cords to remove strain on connections.

Note on Range: Longest remote control operating distances are obtained when the power supply/receiver is in line of sight of the remote control. Operating the remote control inside of houses and other buildings will reduce the remote control's operation distance.

Using the Remote

To power on your lights, press the red ON/OFF button located at the top of the remote. Your Enbrighten Mini Landscape Lights come paired with your remote.

NOTE: Keep remote indoors when not being used. Remote is not waterproof.

Explore the following programmable settings:

Single-Color Selection Feature

Find your favorite color on the remote's color pad and push that button to set all lights to the same color. You can also press the dimming button to adjust from 10 light levels (available for single- and dual-color selection).

Dual-Color Selection Feature

1. Press Color 1, then select a color from the color pad to set the color of every other light starting with the first light.
2. Press Color 2, then select a color from the color pad to set the color of every other light starting with the second light.
3. During selection, press the dimming button to choose one of 10 light levels.

Tunable White Color Selection Feature

Pressing the white button cycles through white selections: 2200K, 2700K, and 5000K.

Strobe Selection Feature

Pressing the strobe button makes the lights strobe through all colors in a random pattern.

Fade Selection Feature

Pressing the fade button makes the lights fade in and out through all colors in a random pattern.

Modes Selection Feature

Press the modes button repeatedly to cycle through preset modes: Twinkle, Multi-Fade, Christmas, St. Patrick's Day, Red, White and Blue, Fall, Spring, Multi-Colors.

NOTE: Your landscape lights will automatically remember the last customized settings and turn back on in the same mode and color scheme.

Timer Selection Feature

Pressing the 2-hour timer button activates a two-hour countdown until lights turn off. Pressing the 4-hour timer button activates a four-hour countdown until lights turn off.

Pair Your Remote with Additional Lights

Your Enbrighten Mini Landscape Lights come with a remote that can be paired to additional sets of landscape lights. It can also be paired with Enbrighten Seasons Café Lights.

To pair a remote with landscape lights or café lights:

1. Plug in (or supply power) to the lights, and within 8 seconds, press and hold the ON/OFF button. The lights will turn white, blink once, and remain white. Your remote and lights are now paired.
• You can pair a remote with as many Enbrighten Seasons Lights as desired.
• Multiple strings can be paired at one time by supplying power to multiple strings simultaneously, then pressing and holding the ON/OFF button within 8 seconds of power-on.

To unpair a remote from a light:

1. Plug in (or supply power) to the lights, and within 8 seconds, press and hold the yellow button (in the bottom left corner of the remote). The lights will turn white, blink twice, and remain white. Your remote and lights are now unpaired.
• Multiple lights can be unpaired at one time by supplying power to multiple lights simultaneously, then pressing and holding the yellow button within 8 seconds of powering on.

Lights can be paired with up to 8 remotes.

Electrical Ratings

Input: 120V, 50/60Hz

Important Information & Warnings

Refer to the manual or visit www.byjasco.com for limitations and restrictions on warranties and product registration.

WARNING: RISK OF ELECTRIC SHOCK

• When using outdoor as portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal injury.
• Ground-fault circuit interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) used for the wet-location portable luminaire. Receptacles with built-in GFCI protection are available.
• Outlets used for powering landscape lights shall comply with all national and local electrical codes. Consult a local electrician if unsure of compliance requirements.
• For use only on GFCI-protected circuits.
• Do not submerge.
• Do not use around aquariums.
• Landscape lights are a wet-location product and have no serviceable parts.
• Do not use with extension cord near water or where water may accumulate.
• Keep lamps at least 16 feet (4.8 meters) from pools and spas.
• Keep plugs and receptacles dry.
• Avoid damage to the cords and lamp assemblies during installation. Periodically inspect landscape lights for physical damage or damage caused by outdoor exposure.
• Replace any damaged landscape lights.
• Do not install in locations where landscape lights can be stepped on.
• Ensure landscape lights are unplugged from power during installation.
• Children should not be allowed to play with landscape lights.
• UL recommends testing GFCI circuits and receptacles every month to ensure proper operation.

WARNING: RISK OF FIRE

• Landscape lights are designed to be mounted with their individual keyhole mounting feature; do not mount by using the main electrical cord or individual drop cords.
• Not intended for installation in ceilings, soffits, cabinets, attics, or other enclosed spaces.

WARNING:

Keep plastic bags away from babies and children. Do not use in cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth and prevent breathing.

Warranty Information

This Jasco product is warrantied for three (3) years with a limited-lifetime replacement warranty on Enbrighten LED light source only.

Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.

Visit www.byjasco.com for warranty details.

Patents pending | www.enbrightenme.com

Model numbers associated: 41366, 41367, 41369, 41657

Version 1 | Last updated: 07/31/2018

Simplify Your Experience with enbrighten®

Automate your lighting with smart timers and plugs. We recommend the following models, available at select retailers or at www.enbrightenme.com.

Recommended Timers & Smart Plugs

• myTouchSmart Outdoor/Indoor Plug-in Timer (Model #26898): Heavy duty and weather resistant with two grounded outlets. Fully customizable time settings.
• myTouchSmart In-Wall Digital Timer (Model #41431): Easy-to-program custom settings, presets, and countdown options. On/off switch opens to reveal program buttons.
• myTouchSmart SunSmart™ In-Wall Digital Timer (Model #33861): Easy-to-program custom settings, presets, and countdown options. Self-adjusts to sunset/sunrise times throughout the year. On/off switch opens to reveal program buttons.
• myTouchSmart Outdoor/Indoor Wi-fi Smart Plug (Model #39845): Schedule and control outdoor or indoor lighting from any mobile or voice-controlled device.

For additional stakes and accessories, visit www.enbrightenme.com or call 1-800-654-8483.

enbrighten café™ Lights

Multiple lengths and styles available now at www.enbrightenme.com.

Classic Series

• Warm White Light 2700K: Linkable up to 750ft.
• Black Cord: 31660 (12ft / 6 Bulbs), 33307 (18ft / 9 Bulbs), 31662 (24ft / 12 Bulbs), 31663 (36ft / 18 Bulbs), 31664 (48ft / 24 Bulbs)
• White Cord: 35604 (12ft / 6 Bulbs), 36803 (24ft / 12 Bulbs), 35608 (48ft / 24 Bulbs)

Vintage Series

• Warm Vintage Light 2200K: Linkable up to 750ft.
• Black Cord: 35626 (12ft / 6 Bulbs), 35629 (24ft / 12 Bulbs), 35631 (48ft / 24 Bulbs)
• White Cord: 35643 (12ft / 6 Bulbs), 35646 (24ft / 12 Bulbs), 35648 (48ft / 24 Bulbs)

Vintage Series (Color & Effect)

• Warm Vintage Light 2200K: Linkable up to 750ft. Connectable up to 230m (750ft.). Features preset color & effect modes, dimmable, 2 or 4 hour timers. Supports any 2 color combinations.
• Black Cord: 37791 (24ft / 12 Bulbs), 37790 (48ft / 24 Bulbs)
• White Cord: 39511 (24ft / 12 Bulbs), 39092 (48ft / 24 Bulbs)