Enbrighten Landscape Lights

Ground Mounting

1. Carefully plan out your installation by laying out the landscape lighting system. Start with the GFCI receptacle and mounting of the controller. The first light can be placed up to 20 feet away from the controller. Each subsequent light can be placed up to 10 feet from the previous light.
2. Mount the controller within an appropriate distance for the polarized plug to reach the receptacle. The controller can be mounted using the keyhole on the rear of the controller or the keyhole ear tabs (See Figure A). Do not lay the controller directly on the ground or where standing water may accumulate (See Figure B). Ensure there is slack in the cord to prevent strain on the controller.
3. Ground mounting has two options for installation:
   • Place the light directly on the ground or garden bedding.
   • Using the provided mount stake. You have been provided 1 stake per light. The stake can be inserted into either keyhole mounting slot located on the bottom of the light. Firmly insert the mounting stake into the keyhole slot, ensuring both tabs lock into place. The stake can then be inserted into the soil or mulch at the desired angle. If the stake requires more than a firm push to be inserted, loosen the soil or remove obstacles such as rocks. The stakes feature cord management features on the sides allowing you to position the cord close to the stake (See Figure C).
   • Cord management: Your Enbrighten landscape lights feature burial-grade cable. This allows you to conceal excess cable by directly burying it in the soil or covering it with garden bedding.

Flat Surface Mounting

Lay out the landscape system in the manner in which you plan to mount it. Only mount lights to a solid support structure such as joists, beams, studs, or other solid mounting surfaces. Use two #6 pan head screws (not included) of an appropriate length for the surface that you are mounting them to properly mount the lights (See Figure D). A mounting template is available for easy mounting.

Single-Color Selection

Find your favorite color on the remote's color pad and simply push that button to set all of the lights the same color. Within this feature, you can also press the dimming button to adjust from 10 different light levels. The dimming option is only available for single- and dual-color selection.

Dual-Color Selection

a) Press Color 1, then select a color from the color pad to set the color of every other light starting with the first light.

b) Press Color 2, then select a color from the color pad to set the color of every other light starting with the second light.

c) During the selection feature, press the dimming button to choose one of 10 different light levels.

Tunable White Color Selection

By pressing the white button, you can cycle through white selections: 2200K, 2700K, and 5000K.

Strobe Selection

By pressing the Strobe button, the lights will strobe through all of the colors in a random pattern.

Fade Selection

By pressing the Fade button, the lights will fade in and out through all of the colors in a random pattern.

Modes Selection

Press the "Modes" button repeatedly to cycle through the following preset modes: Twinkle, Multi Fade, Christmas, St. Patrick's Day, Red, White, and Blue, Fall, Spring, Multi-Colors.

NOTE: Your landscape lights will automatically remember the last customized settings and will turn back on in the same mode and/or color scheme.

Timer Selection

By pressing the 2 hour timer button, you will activate a two-hour countdown until lights turn off. By pressing the 4 hour timer button, you will activate a four-hour countdown until lights turn off.

To Pair Lights with a Remote:

1. Plug in (or supply power) to the lights and within 8 seconds, press and hold the ON/OFF button. The lights will turn white, blink once, and remain white. Your remote and lights are now paired.
2. Multiple strings can be paired at one time with one remote by supplying power to multiple strings at once, then pressing and holding the ON/OFF button within 8 seconds of power on, per the above instructions.

To Unpair Lights from a Remote:

1. Plug in (or supply power) to the lights and within 8 seconds, press and hold the yellow button (in the bottom left corner). The lights will turn white, blink twice, and remain white. Your remote and lights are now unpaired.
2. Multiple lights can be unpaired at one time from one remote by supplying power to multiple lights at once, then pressing and holding the yellow button within 8 seconds of powering on.

General Outdoor Use Warnings:

⚠️ When using outdoors, use portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal injury, including the following:

• Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location portable luminaire. Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety.
• ⚠️ Keep these bags away from babies and children. Do not use in cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth and prevent breathing.

Warranty Information:

This Jasco product is warrantied for three (3) years with a limited-lifetime replacement warranty on Enbrighten LED light source only.

Manufactured in China. Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114. This Jasco product comes with a 3-year limited warranty. Visit www.byjasco.com for warranty details.

Patents pending. www.enbrightenme.com. Version 1 3/5/18.

RISK OF ELECTRIC SHOCK:

• Receptacle outlets used for powering landscape lights shall comply with all national and local electrical codes. Consult a local electrician if unsure of compliance requirements.
• For use only on GFCI protected circuits.
• Do not submerge.
• Do not use around aquariums.
• Landscape lights are a WET LOCATION product and have no serviceable parts.
• Do not use with extension cord near water or where water may accumulate.
• Keep lamps at least 16 feet from pools and spas.
• Keep plugs and receptacles dry.
• Avoid damage to the cords and lamp assemblies during installation. Periodically inspect the landscape lights for physical damage or other damage caused by outdoor exposure to the elements.
• Replace any damaged landscape lights.
• Do not install in locations where landscape lights can be stepped on.
• Ensure landscape lights are unplugged from power during installation.
• Children should not be allowed to play with landscape lights.
• UL recommends testing GFCI circuits and receptacles every month to ensure proper operation.

RISK OF FIRE:

• Landscape lights are designed to be mounted with their individual keyhole mounting feature. Do not mount landscape lights by using the main electrical cord or the individual drop cords.
• Not intended for installation in ceilings, soffits, cabinets, attics, or other enclosed spaces.