FSP180-AxxN3 Series 180W AC-DC Adapter Datasheet

Brand: FSP

Features

Certified IEC 62368-1 & CB 60950-1
Meets USA EISA 2007
Meets Energy Efficiency DOE Level VI
Meets Code of Conduct Version 5 Tier 2
High Reliability
Low Profile
Over Current Protection
Over Temperature Protection
Over Voltage Protection
With PFC Circuit

Safety Standard Approval

TÜV Rheinland Certified, CULUS LISTED, CE, FCC Tested to Comply With FCC Standards FOR HOME OR OFFICE USE, CCC.

Description

This product is an 180 watts AC to DC adapter intended for use in IPC systems, embedded systems, printers, monitors, POS systems, and PoE applications that have high wattage demands. This adapter operates at 90 to 264 VAC input voltage. The unit meets CISPR32 EN55032 CLASS B, EN55024, and FCC PART 15B Class B emission limits, and is designed for ITE application.

Input Specifications

Input voltage:	90-264 VAC
Input frequency:	47-63 Hz
Input current:	100Vac, 240Vac / full load ≤ 1.2A
No load power consumption:	115Vac, 230Vac ≤ 0.5W
Touch current:	264Vac / 50Hz ≤ 0.25mA

Input Specifications (Continued)

Power factor:	115Vac, 230Vac / full load ≥ 0.9
Harmonic Reduction:	Provisions for adding harmonic reduction per EN 61000-3-2 must be present.
Efficiency:	See rating chart
Power turn-on time:	At 100Vac / full load, output voltage shall remain regulation ≤ 3Sec
Hold-up time:	At 100Vac or 240Vac / full load, output voltage shall remain regulation ≥ 10ms
Inrush current:	100Vac, 240Vac / full load, Shall be less than the rating of adapter critical component (including rectifiers, fuse, surge and current limiting device)
Operating altitude:	5000 meters above sea level
Withstand voltage:	Between AC input and secondary applied DC 4242V, test time 1 minute, cut off current shall be less than 10mA
MTBF:	100Vac, 240Vac / full load, 300,000 hours at 25°C, standard SR332

Output Specifications

Output voltage/current: See rating chart

Total output power: 180W

Protection

Over voltage: The adapter will enter into shut down (no output) if over voltage occurs at the output terminal due to an internal fault. The output trip voltage shall not exceed 19/29/35/66* volts. Normal state is restored by AC reset.
Short circuit & Over current: When an internal fault occurs, or an external fault is applied to the power supply causing an overload or short circuit at the output, the power supply shall shut down and enter auto-recovery mode.
Over temperature: The power supply will enter into shut down when abnormal thermal rise occurs. Normal state is restored by AC reset. Set at 60Vac~70Vac.
Brown-out: Set at 60Vac~70Vac.

Environment

Working TEMP.:	0~70°C (≥ 40°C de-rating)
Storage TEMP.:	-20~+80°C
Working Humidity:	20~80% RH non-condensing
Storage Humidity:	10~90% RH non-condensing

Derating Curves

Input Voltage Derating Curve

Textual description: The Input Voltage Derating Curve shows that the output power remains at 100% from 90 VAC to 264 VAC input voltage.

Output Power Derating Curve

Textual description: The Output Power Derating Curve shows that the output power is 100% up to 40°C and then derates as temperature increases, reaching approximately 55% load at 70°C.

Output Voltage/Current Rating Chart

Model	Output Voltage	Output Current	AC Inlet	Efficiency (DOE Level VI)	Efficiency (CoC V5, Tier 2)	Over Voltage Protection
FSP180-AHAN3	12V	15A	C14	≥88%	≥89%	19 Volts
FSP180-AHBN3	12V	15A	C6			29 Volts
FSP180-AJAN3	19.5V	9.23A	C14			35 Volts
FSP180-AJBN3	19.5V	9.23A	C6			66 Volts
FSP180-AAAN3	24V	7.5A	C14
FSP180-AABN3	24V	7.5A	C6
FSP180-AWAN3	54V	3.34A	C14
FSP180-AWBN3	54V	3.34A	C6

EMC Performance

EN55032	Class B conducted, class B radiated
FCC	Class B conducted, class B radiated
VCCI	Class B conducted, class B radiated
EN61000-3-2	Meet class D
EN61000-3-3	Meet regulation
EN61000-4-2	Air discharge: ±15 KV, contact discharge: ±8KV, meet criterion A
EN61000-4-3	80~1000 MHz, 3V/m, 80% AM(1kHz), meet criterion A
EN61000-4-4	Impulse: ±1kV applied to L, N, meet criterion A
EN61000-4-5	±1kV applied differential mode, ±2kV applied common mode, meet criterion A
EN61000-4-6	0.15~80 MHz, 3Vrms, 80% AM(1kHz), meet criterion A
EN61000-4-8	50 Hz or 60Hz, 1A/m, meet criterion A
EN61000-4-11	Voltage Dips: >95% reduction for 0.5 period, meet criterion B; 30% reduction for 25 period, meet criterion C. Voltage Interruptions: >95% reduction for 250 period, meet criterion C.

Power De-rating

100Vac or 240Vac, 0°C to 40°C, 100% load; 50°C, 85% load; 60°C, 70% load; 70°C, 55% load (Shall be less than the rating of adapter critical component, follow FSP specification (adapter)).

Mechanical Specifications

The datasheet includes diagrams detailing the mechanical specifications for different models. These diagrams show dimensions, cable lengths, and connector types.

FSP180-AxAN3 / FSP180-AxBN3 Series

Diagrams illustrate the physical layout, including:

Overall dimensions: Approximately 151.3mm ± 0.5mm (Length) x 75.6mm ± 0.5mm (Width) x 40.0mm ± 0.3mm (Height).
Cable lengths: Main cable approximately 1800mm ± 50mm, with a 110mm ± 30mm and 50mm ± 30mm section for cable ties.
Plug Type: 4-pin power molding (PIN NICKEL PLATING) or equivalent.
Cable Tie: Steel wire, PE plated.

FSP180-AHAN3 Series