FSP180-AxxN3 Series 180W Adapter
Technical Datasheet
FSP180-AxxN3 Series
FEATURES
- Certified IEC 62368-1 & CB 60950-1
- Meets USA EISA 2007
- Meets Energy Efficiency DOE Level VI
- Meets Code of Conduct Version 5 Tier 2
- High Reliability
- Low Profile
- Over Current Protection
- Over Temperature Protection
- Over Voltage Protection
- With PFC Circuit
SAFETY STANDARD APPROVAL
TÜV Rheinland Certified, CULUS LISTED, CE, FCC Tested to Comply With FCC Standards FOR HOME OR OFFICE USE, CCC.
DESCRIPTION
This product is an 180 watts AC to DC adapter intended for use in IPC systems, embedded systems, printers, monitors, POS systems, and PoE applications that have high wattage demands. This adapter operates at 90 to 264 VAC input voltage. The unit meets CISPR32 EN55032 CLASS B, EN55024, and FCC PART 15B Class B emission limits, and is designed for ITE application.
INPUT SPECIFICATIONS
| Parameter | Value |
|---|---|
| Input voltage | 90-264 VAC |
| Input frequency | 47-63 Hz |
| Input current | 100Vac, 240Vac / full load ≤ 1.2A |
| No load power consumption | 115Vac, 230Vac ≤ 0.5W |
| Touch current | 264Vac / 50Hz ≤ 0.25mA |
OUTPUT SPECIFICATIONS
| Parameter | Details |
|---|---|
| Output voltage/current | See rating chart |
| Total output power | 180W |
| Protection: Over voltage | The adapter will enter into shut down when over voltage happens at the output terminal due to an internal fault. The output trip voltage shall not exceed 19/29/35/66* volts. Normal state is restored by AC reset. |
| Protection: Short circuit & Over current | When an internal fault occurs, or an external fault is applied to the power supply causing an overload or short circuit at the output, the power supply shall shut down and enter auto-recovery mode. |
| Protection: Over temperature | The power supply will enter into shut down when abnormal thermal rise occurs. Normal state is restored by AC reset. Set at 60Vac~70Vac. |
| Protection: Brown-out | Set at 60Vac~70Vac |
ENVIRONMENT
| Parameter | Value |
|---|---|
| Working TEMP. | 0~70°C ( > 40°C de-rating) |
| Storage TEMP. | -20~+80°C |
| Working Humidity | 20~80% RH non-condensing |
| Storage Humidity | 10~90% RH non-condensing |
ADDITIONAL INPUT SPECIFICATIONS
| Parameter | Value |
|---|---|
| Power factor | 115Vac, 230Vac / full load ≥ 0.9. Provisions for adding harmonic reduction per EN 61000-3-2 must be present. |
| Efficiency | See rating chart |
| Power turn-on time | At 100Vac / full load, output voltage shall remain regulation ≤ 3Sec |
| Hold-up time | At 100Vac or 240Vac / full load, output voltage shall remain regulation ≥ 10ms |
| Inrush current | 100Vac, 240Vac / full load, Shall be less than the rating of adapter critical component (including rectifiers, fuse, surge and current limiting device) |
| Operating altitude | 5000 meters above sea level |
| Withstand voltage | Between AC input and secondary applied DC 4242V, test time 1 minute, cut off current shall be less than 10mA |
| MTBF | 100Vac, 240Vac / full load, 300,000 hours at 25°C, standard SR332 |
EMC Performance
| Standard | Performance |
|---|---|
| EN55032 | Class B conducted, class B radiated |
| FCC | Class B conducted, class B radiated |
| VCCI | Class B conducted, class B radiated |
| EN61000-3-2 | Meet class D |
| EN61000-3-3 | Meet regulation |
| EN61000-4-2 | Air discharge: ±15 KV, contact discharge: ±8KV, meet criterion A |
| EN61000-4-3 | 80~1000 MHz, 3V/m, 80% AM(1kHz), meet criterion A |
| EN61000-4-4 | Impulse: ±1kV applied to L, N, meet criterion A |
| EN61000-4-5 | ±1kV applied differential mode, ±2kV applied common mode, meet criterion A |
| EN61000-4-6 | 0.15~80 MHz, 3Vrms, 80% AM(1kHz), meet criterion A |
| EN61000-4-8 | 50 Hz or 60Hz, 1A/m, meet criterion A |
| EN61000-4-11 | Voltage Dips: >95% reduction for 0.5 period, meet criterion B; 30% reduction for 25 period, meet criterion C. Voltage Interruptions: >95% reduction for 250 period, meet criterion C. |
Power De-rating
100Vac or 240Vac, 0°C to 40°C, 100% load; 50°C, 85% load; 60°C, 70% load; 70°C, 55% load. (Shall be less than the rating of adapter critical component, follow FSP specification (adapter)).
Curves
Input Voltage Derating Curve
This graph illustrates the output power percentage relative to the input voltage in VAC. The curve shows that as input voltage increases from 90 VAC to 264 VAC, the output power capability remains at 100%.
Output Power Derating Curve
This graph shows the maximum load percentage relative to the ambient temperature. It indicates that the adapter can operate at 100% load up to approximately 40°C, after which the maximum load percentage decreases as temperature rises, reaching around 55% at 70°C.
OUTPUT VOLTAGE/CURRENT RATING CHART
| Model | Output Voltage | Output Current | AC Inlet | Efficiency (DOE Level VI) | Efficiency (CoC V5, Tier 2) | Over Voltage Protection |
|---|---|---|---|---|---|---|
| FSP180-AHAN3 | 12V | 15A | C14 | ≥88% | ≥89% | 19 Volts |
| FSP180-AHBN3 | 12V | 15A | C6 | 29 Volts | ||
| FSP180-AJAN3 | 19.5V | 9.23A | C14 | 35 Volts | ||
| FSP180-AJBN3 | 19.5V | 9.23A | C6 | 66 Volts | ||
| FSP180-AAAN3 | 24V | 7.5A | C14 | 19 Volts | ||
| FSP180-AABN3 | 24V | 7.5A | C6 | 29 Volts | ||
| FSP180-AWAN3 | 54V | 3.34A | C14 | 35 Volts | ||
| FSP180-AWBN3 | 54V | 3.34A | C6 | 66 Volts |
MECHANICAL SPECIFICATIONS
FSP180-AxAN3
This section details the physical dimensions and connector configuration for the FSP180-AxAN3 series. The adapter unit has approximate dimensions of 151.3mm x 75.6mm x 40.0mm. It features a 4-pin power molding plug with nickel plating. The cable length from the adapter to the plug is approximately 1800mm ± 50mm, with a cable tie made of steel wire, PE plated. The input connector is a C14 or C6 type.
FSP180-AxBN3
This section details the physical dimensions and connector configuration for the FSP180-AxBN3 series. The adapter unit has approximate dimensions of 151.3mm x 75.6mm x 40.0mm. It features a 4-pin power molding plug with nickel plating. The cable length from the adapter to the plug is approximately 1800mm ± 50mm, with a cable tie made of steel wire, PE plated. The input connector is a C14 or C6 type.
FSP180-AHAN3
This section details the physical dimensions and connector configuration for the FSP180-AHAN3 model. The adapter unit has approximate dimensions of 177mm x 85.6mm x 32.2mm. It features a 4-pin power molding plug with nickel plating. The cable length from the adapter to the plug is approximately 1500mm ± 50mm, with a cable tie made of steel wire, PE plated. The input connector is a C14 or C6 type.
CONNECTOR SPECIFICATIONS
FSP180-AHAN3
This section provides details on the connector for the FSP180-AHAN3 model. The connector is a DIN plug with 4 pins. Pin assignments and polarity are as follows:
- PIN 1: VO(+) (RED wire)
- PIN 2: (No color specified)
- PIN 3: GND(-) (BLACK wire)
- PIN 4: (No color specified)
