VEVOR Box Style Cat Trees User Manual

Product Overview

This manual provides instructions for the VEVOR Box Style Cat Trees, models SSXG005 and SSXG002. VEVOR is committed to providing tools at competitive prices.

Models: SSXG005 / SSXG002

Contact Information: For product questions or technical support, please visit www.vevor.com/support.

Disclaimer: VEVOR reserves the right to interpret its user manual. Product appearance is subject to the received product. Information may be updated without prior notice.

Safety Instructions

WARNING:

Read this material before using this product. Failure to do so can result in serious injury.

Assembly Precautions:

• Assemble only according to these instructions. Improper assembly can create hazards.
• Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
• Keep the assembly area clean and well-lit.
• Keep bystanders out of the area during assembly.
• Do not assemble if tired or under the influence of alcohol, drugs, or medication.
• Product capabilities apply to properly and completely assembled products only.
• Assemble on a flat, level, hard, and smooth surface capable of safely supporting the cat tree.
• Refer to the Assembly Diagram for parts. Unwrap and separate all parts in a clean work area.

Use Precautions:

• DO NOT SIT OR STAND ON THIS ITEM.
• This product is not a toy. Do not allow children to play with or near this item.
• Do not exceed specified weight capacities.
• Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded cat tree.
• Use as intended only.
• Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

Accessories Table

The following parts are included:

• Panels: A (x1), B (x1), C (x1), D (x1), E (x1), F (x1), G (x1), H (x1), I (x1), J (x1), K (x1), L (x1), M (x1)
• Other Parts: N (x2), O (x1)
• Sisal Columns: 18cm (x1)
• Wrap the Column: 14.5cm (x2), 22cm (x2), 24cm (x1), 30cm (x1)
• Cushions: 6, 7, 8
• Toys: Spring toys (S x1), Furball toys (X2 x1)
• Accessories: Doorknob (U x2), Door stopper (V x2), Anti-tipping rope (W x1), Rotating shaft (Y x4), Adjustable footrest (Z x4)
• Screws: Q1x16 (3-in-1 screws), Q2x4 (M6*40), Q3x2 (M4*22), T1x12 (M4*12), T2x5 (M8*30), T3x4 (M8*70), T4x16 (M3*12)

*Each set comes with a screwdriver and wrench.

Installation Steps

Step 1:

Install the adjustable foot pad (Z x4) on the base (A) as illustrated. Use screws (T1 x12).

Step 2:

Assemble the bottom cabinet using the three-in-one screw installation method. Align holes before tightening. Parts used: B, C, D, J, N (x2), U (x2), V (x2), Y (x4). Screws used: Q1x12, T4x16, Q3x2.

Step 3:

Assemble the corresponding door stopper (V) and the small black nose (U) as shown. Attach hinges to the door and tighten screws (T4x16).

Step 4:

Insert plates I and H into the top groove of the cabinet. Assemble the cat nest above the cabinet using parts E, F, G, H, I. Secure with screws (Q2x4).

Step 5:

Install plank K, plank M, and the corresponding pillars. Attach cushions 7 and 9. Parts used: K, M, 7, 9. Screws used: T3x2, T2x3.

Step 6:

Install the remaining planks and posts. Attach the hairball toy (X1) and spring toy (S). Secure all parts with screws (T2x2, T3x2). Install the anti-tipping rope (W) by plugging the expansion pipe into the wall and fixing the rope with a self-tapping wire. Secure the other side to the cat climbing frame.

Note: The adjustable foot pads at the bottom can be rotated to adjust the height.

Product Parameter

Manufacturer:

Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong 11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS:

SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA:

Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative:

E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative:

YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX