Mcombo Power Recliner Sofa Owner's Manual

Purchaser's Agreement

By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or render inoperable or unsafe any guards, shields, or other safety features of this product. You will not refuse or neglect any retrofit kits that Mcombo may provide to enhance and preserve the safe use of this product.

I. Safety Guidelines

1. Mandatory

Read the safety and other instructions thoroughly before using your Mcombo® product. Failure to follow the guidelines, warnings in this manual, and those located on your product can result in personal injury or product damage and will void the product warranty. Keep this manual for future reference.

2. Danger

• To prevent suffocation, keep plastic bags away from children.
• Do not allow children to play on or near the product when in use. Serious injury or death could occur if a child is under the product when the product is in motion.
• Keep the cord out of reach of small children, and do not use where it may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Do not use this product if it is wet, in water, around water, or any liquid.
• Always leave the product in an upright and closed position. Keep hands and feet clear of the mechanism and all moving parts. The footrest must be completely closed before getting in or out of the product. Only the occupant should operate the product.
• Before moving or troubleshooting, unplug power cords from the outlet and secure the mechanism to prevent unexpected movement of the product.

3. Warning

• Weight Capacity: 350 lbs.
• Do not use outdoors. INDOOR USE ONLY. ? [Indoor Use Only]
• To avoid tip-over, do not put your weight against the back of the product.
• Do not stand, sit, or place extra weight on the arms, back, or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Avoid exposing upholstered product to burning cigarettes or cigars, open flames, and high temperatures.
• Do not operate the unit until the back is installed and locked.
• Do not attempt to disassemble or repair the actuator or pump; no serviceable parts are inside.
• Do not allow the electrical cord to be pinched between moving parts or between the frame and the floor. Do not place the cord under carpet or in a location where it could become worn.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around furniture.
• This product has many moving parts; serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the power supplies and electrical cords away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug, or connector.
• Do not charge your device into the USB charge ports for more than 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not cover the USB charge ports with other heat-dissipating electronic products, as this may prevent heat dissipation and cause overheating or melting.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair. Contact your Mcombo Customer Support.
• A seat is intended for a single occupant, not exceeding 350 pounds. Do not operate the seat with more than one occupant in or on any part of the product.
• If you give this product to someone else, you must include this owner's manual.

4. Symbols Information

The symbols below represent labels used on the product to identify warnings, mandatory actions, and prohibited actions. It is especially important for you to read and understand these symbols completely. Do not remove these labels from your product. Please note that not all the symbols may be used on your product.

• [Read Manual] Read and follow the information in the owner's manual.
• [Weight Limit 350 lbs] Weight Capacity: 350 lbs.
• [No Extension Cord] Do not connect an extension cord to the AC/DC converter.
• [Clear Footrest Area] Do not place objects under the footrest when it is in the fully reclined position.
• [Clear Headrest Area] Do not place objects under the headrest when the headrest of the recliner sofa is in the fully raised position.
• [Pinch Hazard] ? Pinch/Crush Points Hazard.
• [Electrical Hazard] ⚡ Electrical Hazard.
• [Class II Equipment] Class II Equipment.
• [Indoor Use Only] ? Indoor Use Only.

5. Disclaimer

Make sure you read and understand this manual completely before using your Mcombo Product. We are not and cannot be held responsible for any damage or injury incurred due to improper or unsafe use of the Mcombo Product. We specifically disclaim responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances.

II. Assembly Instructions

Notice: Please read these instructions thoroughly before using. Do not plug the power supply in until assembly is complete. Please contact us (See "Mcombo Customer Support" on Page 32) immediately if anything is missing or damaged.

1. Configuration Selection Guide

Notice: Please select the exact sofa you purchased and turn to the exact page to assemble it.

• Loveseat (Please Turn to Page 05 to Assemble)
• Loveseat with Console (Please Turn to Page 13 to Assemble)

2. Product Parameters (Loveseat)

3. Part List (Loveseat)

Notice: Use Mcombo parts only for all replacements.

Box 1 of 4

• A: Left Base x1
• B: Right Base x1

Box 2 of 4

• C: Left Armrest x1
• D: Right Armrest x1

Box 3 of 4

• E: Left Backrest x1
• F: Right Backrest x1

Part Box

• G: Seat Steel Sheet x2
• H: Screw x8
• I: Base Feet x4
• J: Power Adapter x2
• K: Wrench x1
• Q: Plastic Tie x4

4. Assembly Steps (Loveseat)

Step 1 - Bases Assembly

1. Please use iron sheet (Part #G) to connect two seat bases (Part #A & #B).

2. When installing the iron sheets (Part #G), please lightly tighten the screws (Part #H) first, no need to lock them. Keep the iron sheets in a horizontal position, finally tighten all the screws (Part #H) when all two iron sheets (Part #G) are installed.

Please use iron sheet (Part #G) to connect the back of two seat bases (Part #A & #B), no need to tighten screws first. Tighten the screws after both seats have been installed.

ATTENTION: The iron sheet (Part #G) needs to be installed on the seat frame, not under the seat frame.

Diagram Description: Shows parts A and B (seat bases) being connected at the back using part G (seat steel sheet) and secured with screws H. The diagram emphasizes correct placement of G on the frame.

Step 2 - Armrests Assembly

1. Align the brackets of the armrest at the clips of the base (Figure).

2. Push firmly the brackets into the base. Listen for a "click" on each side to ensure the armrest is locked in properly.

ATTENTION: Ensure the two connections on each armrest are all inserted onto the seat tightly.

Diagram Description: Shows armrests C and D being attached to the assembled bases A and B. Arrows indicate pushing the armrests into place until they click.

Step 3 - Backrests Assembly

1. Align the brackets of the backrest at the clips of the seat-back (Figure).

2. Push firmly the brackets into the seat-back. Listen for a "click" on each side to ensure the backrest is locked in properly.

Diagram Description: Shows backrests E and F being attached to the assembled seat structure. Arrows indicate pushing the backrests down until they click into place.

Step 4 - Product Connections

1. Connect wire 'a' from the backrest and seat base together.

2. Connect wire 'b' from the seat and armrest together.

ATTENTION: Please use the plastic clip to organize the cords.

Diagram Description: Shows the wiring connections. Wire 'a' connects the backrest to the seat base. Wire 'b' connects the armrest to the seat. A "WIRING SPECIFICATION" section details connections for Headrest, Power, and USB & Buttons, showing corresponding plugs and sockets.

Step 5 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side of the base; it may look like assembly is finished when you insert the armrest into only one bracket instead of two, but all pressure will apply to one bracket, which is a likely reason that the armrest falls apart from the seat.)
2. Make sure the backrest inserts are locked to the base. (Pull up the backrest to check if it is locked in place.)
3. Make sure all wires are connected tightly.
4. Make sure all wires are not placed at the bottom of the rack and will not be pressed by the frame. (If a wire is pressed by the frame, it will be broken by the frame, and the sofa will stop working.)
5. Make sure all the screws are tightened.

II. Assembly Instructions (Loveseat with Console)

2. Product Parameters (Loveseat with Console)

3. Part List (Loveseat with Console)

Notice: Use Mcombo parts only for all replacements.

Box 1 of 5

• A: Left Base x1
• B: Right Base x1

Box 2 of 5

• C: Left Armrest x1
• D: Right Armrest x1

Box 3 of 5

• E: Left Backrest x1
• F: Right Backrest x1

Part Box 1

• G: Seat Steel Sheet x2
• H: Screw x8 (Spare Parts)
• I: Base Feet x4
• J: Power Adapter x2
• K: Wrench x1
• Q: Plastic Tie x4

Box 4 of 5

• L: Console Backrest x1
• M: Storage Console x1

Part Box 2

• N: Plastic Cover Screws x2
• O: Seat Iron Sheet x2
• H: Screw x12
• I: Base Feet x4

4. Assembly Steps (Loveseat with Console)

Step 1 - Bases Connection

1. Please use seat iron sheets (Part #O) to connect the seat bases (Part #A, #B, and #M).

2. When installing the steel sheets (Part #O), please lightly tighten the screws (Part #H) first, no need to lock them. Keep the steel sheets in a horizontal position, finally tighten all the screws (Part #H) when both steel sheets (Part #O) are installed and the gap between the seats is adjusted.

Note: Please connect the storage console first.

Please use iron sheet (Part #O) to connect the back of two seat bases (Part #A & #B), no need to tighten screws first. Tighten the screws after all seats have been installed.

ATTENTION: The iron sheet (Part #O) needs to be installed on the seat frame, not under the seat frame.

Diagram Description: Shows parts A, B (seat bases), and M (storage console) being connected using part O (seat iron sheets) and secured with screws H. The diagram emphasizes correct placement of O on the frame and the connection of the console.

Step 2 - Armrests Assembly

1. Align the brackets of the armrest at the clips of the base (Figure).

2. Push firmly the brackets into the base. Listen for a "click" on each side to ensure the armrest is locked in properly.

ATTENTION: Ensure the two connections on each armrest are all inserted onto the seat tightly.

Diagram Description: Shows armrests C and D being attached to the assembled bases A, M, and B. Arrows indicate pushing the armrests into place until they click.

Step 3 - Backrests Assembly

1. Please connect the storage console (Part #M) to the console backrest (Part #L) using plastic cover screws (Part #N).

2. Align the brackets of the backrest at the clips of the seat-back (Figure).

3. Push firmly the brackets into the seat-back. Listen for a "click" on each side to ensure the backrest is locked in properly.

ATTENTION: Unzip the zipper behind the console, then put the console backrest on the console and align the holes.

ATTENTION: Fix them with two plastic cover screws. This step does not require tools, but you need to tighten the screws longer because the screw holes are relatively deep.

Diagram Description: Shows the console backrest L being attached to the storage console M using screws N. Then, backrests E and F are attached to the assembled seat structure. Arrows indicate pushing the backrests down until they click into place.

Step 4 - Product Connections

1. Connect wire 'a' from the backrest and seat base together.

2. Connect wire 'b' from the seat and armrest together.

Diagram Description: Shows the wiring connections. Wire 'a' connects the backrest to the seat base. Wire 'b' connects the armrest to the seat. A "WIRING SPECIFICATION" section details connections for Headrest, Power, and USB & Buttons, showing corresponding plugs and sockets.

ATTENTION: Please use the plastic clip to organize the cords.

Step 5 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side of the base; it may look like assembly is finished when you insert the armrest into only one bracket instead of two, but all pressure will apply to one bracket, which is a likely reason that the armrest falls apart from the seat.)
2. Make sure the backrest inserts are locked to the base. (Pull up the backrest to check if it is locked in place.)
3. Make sure all wires are connected tightly.
4. Make sure all wires are not placed at the bottom of the rack and will not be pressed by the frame. (If a wire is pressed by the frame, it will be broken by the frame, and the sofa will stop working.)
5. Make sure all the screws are tightened.

III. Operating Instructions

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed the recommended weight limit.
• Do not use attachments not recommended by the manufacturer.
• Do not use outdoors. INDOOR USE ONLY. ? [Indoor Use Only]
• Keep dry. Do not operate in a wet or moist environment.
• Keep all cords away from heated surfaces and pinch points.
• Always leave the product in an upright and closed position when not in use.
• Periodically check the control and all power cords for visible damage.
• Do not use the footrest as a seat, or for purposes outside its intended use.
• Do not lean or apply downward force to the seat-back while in the recline position.

NOTE: If you discover a problem at any point during the setup and positioning of your power recliner sofa, stop and contact the Mcombo Customer Support immediately. To avoid personal injury or product damage, do not plug the unit into the electrical outlet until the problem is corrected, and do not attempt to fix electrical problems by yourself.

2. Operation Instruction

Control Buttons:

• Type C Charge Port
• USB Charge Port
• Reclining Button Down/up
• Headrest Button Down/up
• Home Button

Diagram Description: Shows a control panel with icons or labels for the Type C Charge Port, USB Charge Port, Reclining Button (Down/Up), Headrest Button (Down/Up), and Home Button.

IV. Care and Maintenance

Your Mcombo product will provide years of superior performance and satisfaction with regular care and maintenance. To maintain the finish quality of your "assistant", please follow the guidelines and cleaning procedures provided below.

Notice: Do not place the product in direct sunlight, as sunlight causes fading. Do not smoke cigarettes while seated in or using the product. Avoid extreme changes in temperature by arranging the product away from radiators, heat, and air vents. Do not use solvent-type cleaners to spot clean. Do not saturate fabric. Please be careful that pet scratches may cause fabric or leather to break.

1. Fabric Care

• Inspect the fabric on a regular basis for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a nonmetallic, stiff bristle brush to remove dust and grime is recommended.
• When liquid spills onto the fabric, please immediately wipe off liquid spills with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water. Make sure that the cloth is not soaking wet. Never let water soak into leather.
• Always be sure to use a soft cloth and never use an abrasive brush or scrubber, as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to make sure they are not damaged or stuck under the product.
• Keep all the electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact Mcombo Customer Support if damage is present; do not fix it by yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of recliner sofa packaging, metal/wood frame components, fabric, and electronic components.

V. Troubleshooting

The following troubleshooting FAQs should summarize what you need to know about your power recliner sofa. If at any time you do not feel comfortable performing the troubleshooting steps listed in this manual, please contact Mcombo Customer Support for service.

NOTE: If the product does not operate properly, please contact the Mcombo Customer Support for help and never attempt to make any repairs or adjustments yourself.

VI. Disassembly Instruction

Notice: Ensure the product is in seated position and its footrest returns to original position. Please unplug the power cord before disassembling. Please refer to the installation steps from back to front and disassemble the product in reverse order.

Step 1 - Disconnect all Connections

Please disconnect all connections on the chair base and backrest before disassembling.

Step 2 - Disassemble Backrests

1. Pushing the metal ears of the backrest inserts outward (Refer to arrow direction).

2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest marked in the picture below and pull it vertically upward.

ATTENTION: After unlocking the metal tabs on both sides of the backrest, pull the backrest upward.

Diagram Description: Shows how to release the backrest by pushing outward on the metal ears/tabs, then pulling the backrest up.

Step 3 - Disassemble Armrests

Notice: 1. Need to remove the backrest first. 2. It is best to remove armrest by two people. 3. When lifting the armrest, be sure to hold the bottom of the armrest to avoid damaging the handrail bag and cup holder.

1. Use your knees to find a support point on the seat and press on the base with your own strength.

2. Hold the two marked positions at the bottom of the armrest and lift the armrest vertically upward. (Refer to arrow direction and the circular marking area.)

ATTENTION: Shake the armrest slightly to loosen the brackets, make it easier to detach from the base.

Diagram Description: Shows how to detach the armrest by applying pressure to the base with knees, then lifting the armrest upwards from marked points.

Step 4 - Disassemble Bases

Please unscrew the screws.

• Loveseat
• Loveseat with Console

Diagram Description: Shows the underside of the bases for both Loveseat and Loveseat with Console, indicating screws that need to be removed.

VII. Warranty

Notice: For products beyond the limited manufacturer warranty period and scope, Mcombo® can also provide replacement service, but a basic charge will be charged according to the circumstances. The warranty only applies to Mcombo® products and does not include any accessories or enhancements. Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

• All warranties begin on the date of delivery.
• All warranties are to the original purchaser from MCOMBO® ONLY.
• MCOMBO® will replace the defective parts or send replacement product provided that the warranty parts have not been subjected to misuse, abuse, or improper service by the consumer, for example, damaged wire arising in consequence of negligence or improper operation.
• Exclusions also include components with damage caused by:
  • Contamination
  • Abuse, misuse, accident, or negligence
  • Commercial use, or use other than normal
  • Improper operation, maintenance, or storage

NOTE: MCOMBO® will pay standard shipping rates on all warranted parts for the first year. We can also sell you replacement parts for a discount price when your product is out of warranty policy.

VIII. Return/ Replacement Policy

Notice: Why don't we recommend returning the item by yourself? Huge cost - UPS/FedEx oversize fee. Need you to take the box to UPS/FedEx facility.

Return/ Replacement Policy

MCOMBO®: You have 30 days from the date of purchase to return any item purchased from our store. Please securely pack the item in its original packaging, including any accessories or manuals that came with the product. To initiate a return, please contact our customer service team at sales@mcombo.com or 323-597-1109 for any help.

RETURN CONDITIONS

We accept the return of items that are in new, unused condition, with original tags attached and all original packaging and other components included. Refunds will be issued in the original form of payment for the price of the item, including taxes.

NOTE:

• Please keep the original packaging in case the product needs to be returned. If the original packaging is not available, the newly found packaging needs to meet the following size standard: UPS/FedEx packaging size standard: (width + height) * 2 + length < 128 inch.
• Please disassemble the product before you return it, otherwise there will be a huge cost as oversized, and it could even exceed your order amount.
• Please do not purchase a return label for a damaged/defective product by yourself.
• If you have any problem returning the product, please contact us immediately; we will do our best to help you with a reasonable solution.

IX. MCOMBO Customer Support

If for any reason, we have fallen short of your expectations, or if you have any questions and suggestions, please refer to the following contact information. We will do our best to work with you to make sure you are entirely satisfied.

• Email: sales@mcombo.com (Respond within 24 hours)
• Phone: 1-323-597-1109 (8:00 a.m. - 4:00 p.m. Monday-Friday, TIME ZONE: PST)

Customer Support Locations:

• DE: 2411 Bear Corbitt Rd STE 1, New Castle, DE, 19720
• TN: 3980 PREMIER AVE, MEMPHIS, TN, 38118
• CA: 2808 Vail Ave, Commerce, CA, 90040