MCombo Power Recliner Sofa

Purchaser's Agreement

By accepting delivery of this product, you agree not to change, alter, or modify this product, or remove or render inoperable or unsafe any guards, shields, or other safety features. You will not refuse or neglect any retrofit kits provided by MCombo to enhance and preserve the safe use of this product.

I. Safety Guidelines

1. Mandatory

Read all safety and other instructions thoroughly before using your MCombo® product. Failure to follow these guidelines, warnings in this manual, and those located on your product can result in personal injury or product damage and will void the product warranty. Keep this manual for future reference.

2. Danger

• To prevent suffocation, keep plastic bags away from children.
• Do not allow children to play on or near the product when in use. Serious injury or death could occur if a child is under the product when it is in motion.
• Keep cords out of reach of small children, and do not use where it may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Do not use this product if it is wet, in water, around water, or any liquid.
• Always keep the product in an upright and closed position. Keep hands and feet clear of the mechanism and all moving parts. The footrest must be completely closed before getting in or out of the product. Only the occupant should operate the product.
• Before moving or troubleshooting, unplug power cords from the outlet and secure the mechanism to prevent unexpected movement of the product.
• Do not operate the unit until the back is installed and locked.
• Do not attempt to disassemble or repair the actuator or pump; there are no serviceable parts inside.
• Do not allow electrical cords to be pinched between moving parts or between the frame and the floor. Do not place cords under carpet or in a location where they could become worn.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around the furniture.
• This product has many moving parts; serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the power supplies and electrical cords away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug, or connector.
• Do not charge your device into the USB charge ports for over 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not cover the USB charge ports with other heat-dissipating electronic products, as this may prevent heat dissipation and cause overheating or melting.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair. Contact your MCombo Customer Support.
• A seat is intended for a single occupant, not exceeding 350 pounds. Do not operate the seat with more than one occupant in or on any part of the product.
• If you give this product to someone else, you must include this owner's manual.

3. Warning

• Weight Capacity: 350 lbs.
• Do not use outdoors. INDOOR USE ONLY.
• To avoid tip-over, do not put your weight against the back of the product.
• Do not stand, sit, or place extra weight on the arms, back, or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Avoid exposing upholstered product to burning cigarettes or cigars, open flames, and high temperatures.

I. Safety Guidelines - Symbols Information

The symbols below represent labels used on the product to identify warnings, mandatory actions, and prohibited actions. It is important to read and understand these symbols completely. Do not remove these labels from your product. Not all symbols may be used on your product.

• ? Read and follow the information in the owner's manual.
• ⚖️ Weight Capacity: 350 lbs.
• ? Do not connect an extension cord to the AC/DC converter.
• ? Do not place objects under the footrest when it is in the fully reclined position.
• ? Do not place objects under the headrest when the headrest of the recliner sofa is in the fully raised position.
• ⚡ Electrical Hazard.
• ⚠️ Pinch/Crush Points Hazard.
• ✅ Class II Equipment.
• ? Indoor Use Only.

5. Disclaimer

Read and understand this manual completely before using your MCombo Product. MCombo is not responsible for any damage or injury incurred due to improper or unsafe use. MCombo specifically disclaims responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances.

II. Assembly Instructions

Notice: Please read these instructions thoroughly before using. Do not plug the power supply in until assembly is complete. Please contact MCombo Customer Support immediately if anything is missing or damaged.

1. Product Parameters

2. Configuration Selection Guide

Notice: Please select the exact sofa you purchased and turn to the exact page to assemble it.

Model 1: 6160-6025 (2 Seater)

Parts: Left & Right Bases (A1, A2), Left & Right Backrests (B1, B2), Left & Right Arms (C1, C2). Start on page 07.

Model 2: 6160-6045 (2 Seater with Console)

Parts: Left & Right Bases (A1, A2), Left & Right Backrests (B1, B2), Left & Right Arms (C1, C2), Console & Console Back (A3, B3). Start on page 09.

Model 3: 6160-3ST-6015 (3 Seater)

Parts: Left & Right Bases (A1, A2), Left & Right Backrests (B1, B2), Left & Right Arms (C1, C2), Middle Seat & Middle Back (A4, B4). Start on page 12.

Model 4: 6160-3ST-6035 (3 Seater with Console)

Parts: Left & Right Bases (A1, A2), Left & Right Backrests (B1, B2), Left & Right Armrests (C1, C2), Console & Console Back (A3, B3), Middle Seat & Middle Back (A4, B4). Start on page 15.

3. Part List

Notice: Use MCombo parts only for all replacements.

Box 1

• A1: Left Base x1
• C1: Left Armrest x1

Box 2

• A2: Right Base x1
• C2: Right Armrest x1

Box 3

• B1: Left Backrest x1
• B2: Right Backrest x1

Part Box 1

• D: Massage Remote x2 (6160-BB-BM01)
• E: Seat Iron Sheet x2
• F: Wrench x1
• G1: Bolt & Washer & Nut x8
• H: Power Adapter x2 (6160-DD-APA)
• I: Base Feet x4

Box 4

• A3: Storage Console x1
• B3: Console Backrest x1

Box 5

• B4: Middle Backrest x1
• A4: Middle Base x1

Part Box 2 (In Box 4)

• E: Seat Iron Sheet x2
• F: Wrench x1
• G2: Bolt & Washer x4
• K: Plastic Cover Screws x2

Part Box 3

• E: Seat Iron Sheet x2
• F: Wrench x1
• G2: Bolt & Washer x8
• I: Base Feet x4

4. Assembly Steps

Step 1 - Bases Connection

2 Seater (Box1, Box2, Box3)

Instructions:

1. Use seat iron sheets (Part #E) to connect the seat bases (Part #A1, and #A2).
2. Do not tighten the bolts until all bases are connected and properly adjusted.

Note: Please connect the left base first.

ATTENTION: The seat iron sheet needs to be installed on the iron frame, not under the iron frame.

Proceed to page 19 to continue with the next steps.

2 Seater with Console (Box1, Box2, Box3, Box4)

Instructions:

1. Use seat iron sheets (Part #J) to connect the seat bases (Part #A1, #A2) and storage console (Part #A3).
2. Do not tighten the bolts until all bases are connected and properly adjusted.

Note: Please connect the left base and right base first.

ATTENTION: The seat iron sheet needs to be installed on the iron frame, not under the iron frame.

Proceed to page 19 to continue with the next steps.

Step 2 - Console Back Assembly (For Product with Console Only)

1. Please connect the storage console (Part #A3) to the console backrest (Part #B3).

ATTENTION: Unzip the zipper behind the console, then put the console backrest on the console and align the holes. Fix them with two plastic cover screws. This step does not require tools, but you need to tighten the screws longer because the screw holes are relatively deep.

Proceed to page 19 to continue with the next steps.

3 Seater (Box1, Box2, Box3, Box5)

Instructions:

1. Use seat iron sheets (Part #E) to connect the seat bases (Part #A1, #A2, and #A4).
2. Do not tighten the bolts until all bases are connected and properly adjusted.

Note: Please install the seat iron sheets on the left and right bases first.

ATTENTION: The seat iron sheet needs to be installed on the iron frame, not under the iron frame.

Proceed to page 19 to continue with the next steps.

3 Seater with Console (Box 1, Box 2, Box 3, Box 4, Box 5)

Instructions:

1. Use seat iron sheets (Part #E, #J) to connect the seat bases (Part #A1, #A2 and #A4) and storage console (Part #A3).
2. Do not tighten the bolts until all bases are connected and properly adjusted.

Note: Please install the seat iron sheets on the left and middle base first.

ATTENTION: The seat iron sheet needs to be installed on the iron frame, not under the iron frame.

Proceed to page 19 to continue with the next steps.

Step 3 - Armrests Assembly (For All Products)

1. Align the brackets of the armrest at the clips of the base (Figure).

2. Push firmly the brackets into the base. Listen for a "click" on each side to ensure the armrest is locked in properly.

ATTENTION: Ensure the two connections on each armrest are all inserted onto the seat tightly.

Shake the armrest slightly to loosen the brackets, making it easier to detach from the base.

Step 4 - Backrests Assembly (For All Products)

1. Align the brackets of the backrest at the clips of the seat-back (Figure).

2. Push firmly the brackets into the seat-back. Listen for a "click" on each side to ensure the backrest is locked in properly.

ATTENTION: Remove the plastic cap before assembling the backrest.

Step 5 - Product Connections (For All Products)

1. Connect wires of the same color from the backrest and seat base together (labeled 'a' and 'b').
2. Connect wire 'c' from the backrest to the massage remote.
3. The USB socket is located in the bottom of the recliner armrest.

WIRING SPECIFICATION:

• Massage Wires: Connect 'a' to 'a' and 'b' to 'b'.
• Massage Remote, USB & Reclining Buttons: Connect 'c' to the corresponding ports.

ATTENTION: Please use the plastic clip to organize the cords.

Step 6 - Paste Velcro (For All Products)

1. Place the loveseat in the reclined position.
2. Pull out the Velcro in the gap between the base and the backrest and paste it well.

Step 7 - Final Check

1. Ensure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side of the base; it looks like assembly is finished when you insert the armrest into only one bracket instead of two. However, all pressure will apply to one bracket, which is a likely reason the armrest falls apart from the seat.)
2. Ensure the backrest inserts are locked to the base. (Pull up the backrest to check if it is locked in place.)
3. Ensure all wires are connected tightly.
4. Ensure all wires are not placed at the bottom of the rack and will not be pressed by the frame. (If a wire is pressed by the frame, it will be broken, and the sofa will stop working.)
5. Ensure all screws are tightened.

III. Operating Instructions

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed the recommended weight limit.
• Do not use attachments not recommended by the manufacturer.
• Do not use outdoors. INDOOR USE ONLY.
• Keep dry. Do not operate in a wet or moist environment.
• Keep all cords away from heated surfaces and pinch points.
• Always leave the product in an upright and closed position when not in use.
• Periodically check the control and all power cords for visible damage.
• Do not use the footrest as a seat, or for purposes outside its intended use.
• Do not lean or apply downward force to the seat-back while in a reclined position.

NOTE: If you discover a problem at any point during setup or positioning, stop and contact MCombo Customer Support immediately. To avoid personal injury or product damage, do not plug the unit into the electrical outlet until the problem is corrected, and do not attempt to fix electrical problems yourself.

2. Operation Instruction

Seated

When you want to take a short break, there is no need to operate the sofa; you will get a comfortable experience.

Relaxing

When you want to relax, adjust the footrest position.

Napping

When you want to take a nap, you can adjust the backrest to the right position while raising the footrest to relax.

Reading

When you want to read in your spare time, adjust your sofa and explore a whole new world.

Massage Remote Operation Instruction

• HEAT: Turn on/off heat function.
• POWER: Turn on/off remote control (only controls massage function).
• MODE: Press to select 3 different massage modes.
• TIMER: The timer can be set in fixed time: 10 / 20 / 30 minutes.
• INTENSITY: Press to adjust massage intensity from low to high.
• POINTS: Control massage points (back, lumbar, thigh).

NOTE: Use the heated function only: Turn off the POWER button, turn on the HEAT button. (Heating function works with vibration separately.)

IV. Care and Maintenance

Your MCombo product will provide years of superior performance and satisfaction with regular care and maintenance. To maintain the finish quality of your "assistant", please follow the guidelines and cleaning procedures provided below.

Notice:

• Do not place the product in direct sunlight, as sunlight causes fading.
• Do not smoke cigarettes while seated in or using the product.
• Avoid extreme changes in temperature by arranging the product away from radiators, heat, and air vents.
• Do not use solvent-type cleaners to spot clean.
• Do not saturate fabric.
• Be careful that pet scratches may cause fabric or leather to break.

1. Fabric Care

• Inspect the fabric regularly for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a non-metallic, stiff bristle brush to remove dust and grime is recommended.
• When liquid spills onto the fabric, please immediately wipe off the spills with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water. Make sure the cloth is not soaking wet. Never let water soak into the leather.
• Always use a soft cloth and never use an abrasive brush or scrubber, as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to make sure they are not damaged or stuck under the product.
• Keep all electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact MCombo Customer Support if damage is present; do not fix it yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of recliner sofa packaging, metal/wood frame components, fabric, and electronic components.

V. Troubleshooting

The following troubleshooting FAQs should summarize what you need to know about your power recliner sofa. If at any time you do not feel comfortable performing the troubleshooting steps listed in this manual, please contact MCombo Customer Support for service.

NOTE: If the product does not operate properly, please contact MCombo Customer Support for help and never attempt to make any repairs or adjustments yourself.

VI. Disassembly Instructions

Notice:

• Ensure the product is in a seated position and its footrest is returned to the original position.
• Please unplug the power cord before disassembling.
• Please refer to the installation steps from back to front and disassemble the product in reverse order.

Step 1 - Disconnect all Connections

Please disconnect all connections on the chair base and backrest before disassembling.

Step 2 - Disassemble Backrests

1. Push the metal ears of the backrest inserts outward (Refer to arrow direction).
2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest marked in the picture below and pull it vertically upward.
3. Please unscrew the console back screws.

ATTENTION: After unlocking the metal tabs on both sides of the backrest, pull the backrest upward.

Step 3 - Disassemble Armrests

Notice:

• Need to remove the backrest first.
• It is best to remove the armrest by two people.
• When lifting the armrest, be sure to hold the bottom of the armrest to avoid damaging the handrail bag and cup holder.

1. Use your knees to find a support point on the seat and press on the base with your own strength.

2. Hold the two marked positions at the bottom of the armrest and lift the armrest vertically upward (Refer to arrow direction and the circular marking area).

ATTENTION: Shake the armrest slightly to loosen the brackets, making it easier to detach from the base.

Step 4 - Disassemble Bases

Please unscrew the bolts.

Diagrams show disassembly for 2 Seater, 2 Seater with Console, 3 Seater, and 3 Seater with Console configurations.

VII. Warranty

Notice:

• For products beyond the limited manufacturer warranty period and scope, MCombo® can also provide replacement service, but a basic charge will be applied according to the circumstances.
• The warranty only applies to MCombo® products and does not include any accessories or enhancements.
• Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

All warranties begin on the date of delivery. All warranties are to the original purchaser from MCOMBO® ONLY.

• MCOMBO® will replace defective parts or send replacement product provided that the warranty parts have not been subjected to misuse, abuse, or improper service by the consumer (e.g., damaged wire due to negligence or improper operation).
• Exclusions also include components with damage caused by: Contamination, Abuse, misuse, accident, or negligence, Commercial use, or use other than normal, Improper operation, maintenance, or storage.

NOTE: MCOMBO® will pay standard shipping rates on all warranted parts for the first year. Replacement parts can also be purchased at a discount price when the product is out of warranty.

VIII. Return/ Replacement Policy

Notice: Why don't we recommend returning the item by yourself?

• Huge cost - UPS/FedEx oversize fee.
• You need to take the box to a UPS/FedEx facility.

Return/ Replacement Policy

You have 30 days from the date of purchase to return any item purchased from our store. Please securely pack the item in its original packaging, including any accessories or manuals that came with the product. To initiate a return, please contact our customer service team at sales@mcombo.com or call 323-597-1109 for assistance.

RETURN CONDITIONS

We accept returns of items that are in new, unused condition, with original tags attached and all original packaging and other components included. Refunds will be issued in the original form of payment for the price of the item, including taxes.

NOTE:

• Please keep the original packaging in case the product needs to be returned. If the original packaging is not available, the replacement packaging needs to meet the following size standard: UPS/FedEx packaging size standard: (width + height) * 2 + length < 128 inches.
• Please disassemble the product before you return it; otherwise, there will be a huge cost for oversized items, and it could even exceed your order amount.
• Please do not purchase a return label for a damaged/defective product yourself.
• If you have any problems returning the product, please contact us immediately. We will do our best to help you with a reasonable solution.

IX. MCOMBO Customer Support

If for any reason, we have fallen short of your expectations, or if you have any questions and suggestions, please refer to the following contact information. We will do our best to work with you to ensure you are entirely satisfied.

• Email: sales@mcombo.com (Respond within 24 hours)
• Phone: 1-323-597-1109 (8:00 a.m. -- 4:00 p.m. Monday--Friday, TIME ZONE: PST)

Locations:

• New Castle, DE: 2411 Bear Corbitt Rd STE 1, New Castle, DE, 19720
• Memphis, TN: 3980 PREMIER AVE, MEMPHIS, TN, 38118
• Commerce, CA: 2808 Vail Ave, Commerce, CA, 90040