MCombo Power Recliner Sofa

Table of Contents

This manual covers the following sections:

• I. SAFETY GUIDELINES
• II. ASSEMBLY INSTRUCTIONS
• III. OPERATING INSTRUCTIONS
• IV. CARE AND MAINTENANCE
• V. TROUBLESHOOTING
• VI. DISASSEMBLY INSTRUCTION
• VII. WARRANTY
• VIII. RETURN/ REPLACEMENT POLICY
• IX. MCOMBO CUSTOMER SUPPORT

I. SAFETY GUIDELINES

1. Mandatory

Read the safety and other instructions thoroughly before using your MCombo® product. Failure to follow the guidelines, warnings in this manual, and those located on your product can result in personal injury or product damage and will void the product warranty. Keep this manual for future reference.

2. Danger

• To prevent suffocation, keep plastic bags away from children.
• Do not allow children to play on or near the product when in use. Serious injury or death could occur if a child is under the product when the product is in motion.
• Keep cords out of reach of small children, and do not use where it may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Do not use this product if it is wet, in water, around water, or any liquid.
• Always leave the product in an upright and closed position. Keep hands and feet clear of the mechanism and all moving parts. The footrest must be completely closed before getting in or out of the product. Only the occupant should operate the product.
• Before moving or troubleshooting, unplug power cords from the outlet and secure the mechanism to prevent unexpected movement of the product.
• Do not operate the unit until the back is installed and locked.
• Do not attempt to disassemble or repair the actuator or pump; no serviceable parts are inside.
• Do not allow the electrical cord to be pinched between moving parts or between the frame and the floor. Do not place the cord under carpet or in a location where it could become worn.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around the furniture.
• This product has many moving parts; serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the power supplies and electrical cords away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug, or connector.
• Do not charge your device into the USB charge ports over 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not overlay the USB charge ports with other heat-dissipating electronic products. This may prevent heat dissipation and cause overheating or melting.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair. Contact your MCombo Customer Support.
• A seat is intended for a single occupant, not exceeding 350 pounds. Do not operate the seat with more than one occupant in or on any part of the product.
• If you give this product to someone else, you must include this owner's manual.

3. Warning

• Weight Capacity: Each seat can support a weight of up to 350 pounds.
• Do not use outdoors. INDOOR USE ONLY.
• To avoid tip over, do not put your weight against the back of the product.
• Do not stand, sit, or place extra weight on the arms, back, or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Avoid exposing upholstered product to burning cigarettes or cigars, open flames, and high temperatures.

4. Symbols Information

The symbols below represent labels used on the product to identify warnings, mandatory actions, and prohibited actions. It is especially important for you to read and understand these symbols completely. Do not remove these labels from your product. Please note that not all the symbols may be used on your product.

• Read and follow the information in the owner's manual: ? An icon depicting a person reading a booklet.
• Weight Capacity: 350 lbs: ⚖️ An icon of a person sitting on a scale, indicating a weight limit.
• Do not connect an extension cord to the AC/DC converter: ? ❌ An icon showing a plug with a line through it connected to an adapter.
• Do not place objects under the footrest when is in fully reclined position: ⚠️ An icon showing a footrest in a reclined position with a red circle and slash over an object placed underneath.
• Do not place objects under the headrest when the headrest of the recliner sofa is in the fully raised position: ⚠️ An icon showing a headrest in a raised position with a red circle and slash over an object placed underneath.
• Pinch/Crush Points Hazard: ⚠️ A triangular warning sign with an exclamation mark and an illustration of fingers being pinched.
• Electrical Hazard: ⚡ A lightning bolt symbol within a triangle.
• Class II Equipment: ⚙️ A square symbol with a circle inside, indicating double insulation.
• Indoor Use Only: ? ❌ An icon of a house with a line through it, indicating it's not for outdoor use.

5. Disclaimer

Make sure you read and understand this manual completely before using your MCombo Product. We are not and cannot be held responsible for any damage or injury incurred due to improper or unsafe use of the MCombo Product. We specifically disclaim responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances.

II. ASSEMBLY INSTRUCTIONS

Notice:

• Please read these instructions thoroughly before using.
• Do not plug the power supply in until assembly is complete.
• Please contact MCombo Customer Support immediately if anything is missing or damaged.

1. Configuration Selection Guide

Notice: Please select the exact sofa configuration you purchased and turn to the corresponding page to assemble it.

• Loveseat: Please Turn to Page 08 to Assemble.
• Loveseat with Console: Please Turn to Page 14 to Assemble.
• Sofa: Please Turn to Page 20 to Assemble.

Assembly Steps (Loveseat)

Parts Included:

• Box 6160-PR635-1: A - Left Base x 1, B - Right Base x 1
• Box 6160-PR635-3: E - Left Backrest x 1, F - Right Backrest x 1
• Box 6160-PR635-4: C - Left Armrest x 1, D - Right Armrest x 1
• Part Box: G - Power Adapter x 2, H - Protective glove x 2, I - Cylindrical Pin x 2, J - Plastic Tie x 4

Step 1 - Bases Assembly

1. First, align the two bases (A and B) and flip them forward, ensuring the footrests are facing down.
2. Lift the left base (A) slightly upward and slide the two notches on its frame to the corresponding protrusions on the right base frame (B), aligning the holes in the middle of both frames.

   For easier installation, please ensure that the footrests are facing down.

3. Once the holes on both frames are aligned, insert the cylindrical pin (I) to secure the two bases.

   Make sure the two metal pieces are aligned and on the same plane before inserting the cylindrical pin.

Step 2 - Armrests Assembly

1. Align the brackets of the armrest (C, D) at the clips of the base (A, B).
2. Push firmly the brackets into the base. Listen for a "click" on each side to ensure the armrest is locked in properly.

   Ensure the two connections on each armrest are all inserted onto the seat tightly.

Step 3 - Backrests Assembly

1. Align the brackets of the backrest (E, F) at the clips of the seat-back.

   Visual Description: Diagram shows backrests E and F being lowered onto the seat frame, aligning with receiving slots.

2. Push firmly the brackets into the seat-back. Listen for a "click" on each side to ensure the backrest is locked in properly.

   Remove the plastic cap before assembling backrest.

Step 4 - Product Connections

1. Connect the chairs according to the following wiring diagram.

   Visual Description of Wiring: Two power cords extend from the bases of the left and right sections. Each cord splits into two connectors: one for the motor and one for the USB/Type-C ports. These connect to corresponding ports on the other section or the main power adapter.

2. Attach the chair-back to the velcro on the bottom of the chair base.

Step 5 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side of the base; assembly is finished when you insert the armrest into only one bracket, however, all pressure will apply to one bracket, which is a likely reason that the armrest falls apart from the seat.)
2. Make sure the backrest inserts are locked to the base. (Pull up the backrest to check if it is locked in place.)
3. Make sure all wires are connected tightly.
4. Make sure all wires are not placed at the bottom of the rack and will not be pressed by frame. (If the wire is pressed by the frame, the wire will be broken by the frame and the sofa will stop working.)
5. Make sure all the screws are tightened.

Assembly Steps (Loveseat with Console)

Parts Included:

• Box 6160-PR635-1: A - Left Base x 1, B - Right Base x 1
• Box 6160-PR635-2: (Not specified, likely part of base assembly)
• Box 6160-PR635-3: E - Left Backrest x 1, F - Right Backrest x 1
• Box 6160-PR635-4: C - Left Armrest x 1, D - Right Armrest x 1
• Box 6160-PR635CA: K - Storage Console x 1, L - Console Backrest x 1
• Box 6160-PR635MS: M - Middle Seat x 1
• Box 6160-PR635MB: O - Middle Backrest x 1
• Part Box: G - Power Adapter x 2, H - Protective glove x 2, I - Cylindrical Pin x 2, J - Plastic Tie x 4, N - Plastic Cover x 2

Step 1 - Bases Assembly

1. First, align the two bases (A and B) and the storage console (K), then flip them forward, the footrests are facing down.
2. Lift the console (K) slightly upward and slide the two notches on the console frame into the corresponding protrusions on the right base frame (B), aligning the holes in the middle of both frames.

   For easier installation, please ensure that the footrests are facing down.

3. Once the holes on both frames are aligned, insert the cylindrical pin (I) to secure the storage console (K) and the right base (B).
4. Follow the same steps to install the left base (A), securing both bases and the storage console.

   Make sure the two metal pieces are aligned and on the same plane before inserting the cylindrical pin.

Step 2 - Armrests Assembly

1. Align the brackets of the armrest (C, D) at the clips of the base (A, B).
2. Push firmly the brackets into the base. Listen for a "click" on each side to ensure the armrest is locked in properly.

   Ensure the two connections on each armrest are all inserted onto the seat tightly.

Step 3 - Backrests Assembly

1. Align the brackets of the backrest (E, F) at the clips of the seat-back.

   Visual Description: Diagram shows backrests E and F being lowered onto the seat frame, aligning with receiving slots.

2. Push firmly the brackets into the seat-back. Listen for a "click" on each side to ensure the backrest is locked in properly.

   Remove the plastic cap before assembling backrest.

3. Please connect the storage console (Part #K) to the console backrest (Part #L) using plastic cover screws (Part #N).

Step 4 - Product Connections

1. Connect the chairs according to the following wiring diagram.

   Visual Description of Wiring: Power cords from bases A, B, and console K connect to each other and to the main power adapter. Connections include motor power and USB/Type-C ports.

2. Attach the chair-back to the velcro on the bottom of the chair base.

Step 5 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side of the base; assembly is finished when you insert the armrest into only one bracket, however, all pressure will apply to one bracket, which is a likely reason that the armrest falls apart from the seat.)
2. Make sure the backrest inserts are locked to the base. (Pull up the backrest to check if it is locked in place.)
3. Make sure all wires are connected tightly.
4. Make sure all wires are not placed at the bottom of the rack and will not be pressed by frame. (If the wire is pressed by the frame, the wire will be broken by the frame and the sofa will stop working.)
5. Make sure all the screws are tightened.

Assembly Steps (Sofa)

Parts Included:

• Box 6160-PR635-1: A - Left Base x 1, B - Right Base x 1
• Box 6160-PR635-2: (Not specified)
• Box 6160-PR635-3: E - Left Backrest x 1, F - Right Backrest x 1
• Box 6160-PR635-4: C - Left Armrest x 1, D - Right Armrest x 1
• Box 6160-PR635MS: M - Middle Seat x 1
• Box 6160-PR635MB: O - Middle Backrest x 1
• Part Box: G - Power Adapter x 2, H - Protective glove x 2, I - Cylindrical Pin x 2, J - Plastic Tie x 4

Step 1 - Bases Assembly

1. First, align all the bases (A, M, B), then flip them forward, the footrests are facing down.
2. Lift the middle base (M) slightly upward and slide the notches into the corresponding protrusions on the right base frame (B), aligning the holes in the middle of both frames.

   For easier installation, please ensure that the footrests are facing down.

3. Once the holes on frames are aligned, insert the cylindrical pins (I) to secure the middle base (M) and right base (B).
4. Follow the same steps to install the left base (A), securing all bases.

   Make sure the two metal pieces are aligned and on the same plane before inserting the cylindrical pin.

Step 2 - Armrests Assembly

1. Align the brackets of the armrest (D, C) at the clips of the base (A, B).
2. Push firmly the brackets into the base. Listen for a "click" on each side to ensure the armrest is locked in properly.

   Ensure the two connections on each armrest are all inserted onto the seat tightly.

Step 3 - Backrests Assembly

1. Align the brackets of the backrest (F, O, E) at the clips of the seat-back.

   Visual Description: Diagram shows backrests F, O, and E being lowered onto the seat frame, aligning with receiving slots.

2. Push firmly the brackets into the seat-back. Listen for a "click" on each side to ensure the backrest is locked in properly.

   Remove the plastic cap before assembling backrest.

Step 4 - Product Connections

1. Connect the chairs according to the following wiring diagram.

   Visual Description of Wiring: Power cords from bases A, B, and middle seat M connect to each other and to the main power adapter. Connections include motor power and USB/Type-C ports.

2. Attach the chair-back to the velcro on the bottom of the chair base.

Step 5 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side of the base; assembly is finished when you insert the armrest into only one bracket, however, all pressure will apply to one bracket, which is a likely reason that the armrest falls apart from the seat.)
2. Make sure the backrest inserts are locked to the base. (Pull up the backrest to check if it is locked in place.)
3. Make sure all wires are connected tightly.
4. Make sure all wires are not placed at the bottom of the rack and will not be pressed by frame. (If the wire is pressed by the frame, the wire will be broken by the frame and the sofa will stop working.)
5. Make sure all the screws are tightened.

III. OPERATING INSTRUCTIONS

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed recommended weight limit.
• Do not use attachments not recommended by the manufacturer.
• Do not use outdoors. INDOOR USE ONLY.
• Keep dry. Do not operate in a wet or moist environment.
• Keep all cords away from heated surfaces and pinch points.
• Always leave the product in an upright and closed position when not in use.
• Periodically check the control and all power cords for visible damage.
• Do not use the footrest as a seat, or for purposes outside its intended use.
• Do not lean or apply downward force to the seat-back while in recline position.

NOTE: If you discover a problem at any point during the setup and positioning of your power recliner sofa, stop and contact the MCombo Customer Support immediately. To avoid personal injury or product damage, do not plug the unit into the electrical outlet until the problem is corrected and do not attempt to fix electrical problems by yourself.

2. Control Buttons

Visual Description of Control Panel: A rectangular control panel with two main buttons and two USB ports.

• Seated: ▶️ Close (Footrest retracts, backrest moves upright)
• Relaxing: ▶️ Open (Footrest extends, backrest reclines)
• USB Charge Port: Standard USB-A port.
• Type-C Charge Port: USB Type-C port.

Operating Modes

• Seated: When you want to take a short break, there is no need to operate the sofa; you will get a comfortable experience.
• Relaxing: When you want to relax, press and hold the open button to adjust the footstool position.
• Napping: When you want to take a nap, you can adjust the backrest to the right position while raising the footrest completely to relax.
• Reading: When you want to read in your spare time, adjust your sofa and explore a whole new word.

IV. CARE AND MAINTENANCE

Your MCombo product will provide years of superior performance and satisfaction with regular care and maintenance. To maintain the finish quality of your "assistant", please follow the guidelines and cleaning procedures provided below.

Notice:

• Do not place the product in direct sunlight, as sunlight causes fading.
• Do not smoke cigarettes while seated in or using the product.
• Avoid extreme changes in temperature by arranging the product away from radiators, heat and air vents.
• Do not use solvent-type cleaners to spot clean.
• Do not saturate fabric.
• Please be careful that pet scratch may cause fabric or leather break.

1. Fabric Care

• Inspect the fabric on a regular basis for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a nonmetallic, stiff bristle brush to remove dust and grime is recommended.
• When liquid spills onto the fabric, please immediately wipe off liquid spills with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water. Make sure that the cloth is not soaking wet. Never let water soak into leather.
• Always be sure to use a soft cloth and never use an abrasive brush or scrubber, as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to make sure they are not damaged or stuck under the product.
• Keep all the electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact MCombo Customer Support if damage is present; do not fix it by yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of recliner sofa packaging, metal/wood frame components, fabric, electronic components.

V. TROUBLESHOOTING

The following troubleshooting FAQs should summarize what you need to know about your power recliner sofa. If at any time you do not feel comfortable performing the troubleshooting steps listed in this manual, please contact MCombo Customer Support for service.

NOTE: If the product does not operate properly, please contact the MCombo Customer Support for help and never attempt to make any repairs or adjustments yourself.

VI. DISASSEMBLY INSTRUCTION

Notice:

• If you have purchased the loveseat or sofa, you can disassemble it by referring to the following steps.
• Ensure the product is in seated position and its footrest return to original position.
• Please unplug the power cord before disassembling.
• Please refer to the installation steps from back to front and disassemble the product in reverse order.

Step 1 - Disconnect all Connections

Please disconnect all connections on the chair base and backrest before disassembling.

Step 2 - Disassemble Backrests

1. Pushing the metal ears of the backrest inserts outward (Refer to arrow direction).

   Visual Description: Diagram shows the backrest being detached by pushing outward on metal tabs near the connection points.

2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest marked in the picture below and pull it vertically upward.

   Visual Description: Diagram shows the backrest being pulled upwards from the seat base after the metal lugs are released.

Step 3 - Disassemble Armrests

Notice:

1. Need to remove the backrest first.
2. It is best to remove armrest by two people.
3. When lifting the armrest, be sure to hold the bottom of the armrest to avoid damaging the handrail bag and cup holder.

1. Use your knees to find a support point on the seat and press on the base with your strength.

   Visual Description: Diagram shows a person using their knees to brace the sofa base while applying upward pressure.

2. Hold the two marked positions at the bottom of the armrest and lift the armrest upward. (Refer to arrow direction and the circular marking area.)

   Visual Description: Diagram shows the armrest being lifted upwards from the base, with arrows indicating the direction of force. A circular inset highlights the connection points.

Attention: Shake the armrest slightly to loosen the brackets, make it easier to detach from the base.

Step 4 - Disassemble Bases

1. First, flip the two bases and the storage console forward, the footrests are facing down.
2. Remove the cylindrical pin between the left base frame and the console frame.

   Visual Description: Diagram shows the bases and console flipped forward. An inset shows a cylindrical pin being removed from the connection point between the console and a base.

3. Lift the left base slightly upward and slide the two notches on the left base frame out of the protrusions to disassemble the left base.

   Visual Description: Diagram shows the left base being lifted and slid away from the console/right base. An inset shows the notches disengaging from protrusions.

4. Follow the same steps to disassemble the storage console from the right base.

VII. WARRANTY

Notice:

• For product beyond the limited manufacturer warranty period and scope, MCombo® can also provide replacement service, but a basic charge will be charged according to the circumstances.
• The warranty only applies to MCombo® products and does not include any accessories or enhancements.
• Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

All warranties begin on the date of delivery.

All warranties are to the original purchaser from MCOMBO® ONLY.

• MCOMBO® will replace the defective parts or send replacement product provided that the warranty parts have not been subjected to misuse, abuse or improper service by the consumer, for example, damaged wire arising in consequence of negligence or improper operation.
• Exclusions also include components with damage caused by: Contamination, Abuse, misuse, accident, or negligence, Commercial use, or use other than normal, Improper operation, maintenance, or storage.

NOTE: MCOMBO® will pay standard shipping rates on all warranted parts for the first year. We can also sell you replacement part for a discount price when your product is out of warranty policy.

VIII. RETURN/ REPLACEMENT POLICY

Notice

Why don't we recommend returning the item by yourself?

• Huge cost - UPS/FedEx oversize fee.
• Need you to take the box to UPS/FedEx facility.

Return/ Replacement Policy

MCOMBO®

You have 30 days from the date of purchase to return any item purchased from our store. Please securely pack the item in its original packaging, including any accessories or manuals that came with the product. To initiate a return, please contact our customer service team at sales@m-combo.com / 323-597-1109 for any help.

RETURN CONDITIONS

We accept the return of items that are in new, unused condition, with original tags attached and all original packaging and other components included. Refunds will be issued in the original form of payment for the price of the item, including taxes.

NOTE:

• Please keep the original packaging in case the product needs to be returned. If the original packaging is not available, the newly found packaging needs to meet the following size standard: UPS/FedEx packaging size standard: (width+ height) * 2+ length< 128 inch.
• Please disassemble the product before you return it, otherwise there will be a huge cost as oversized and it could even exceed your order amount.
• Please do not purchase return label for a damaged/defective product by yourself.
• If you have any problem to return the product, please contact us immediately, we will do our best to help you with a reasonable solution.

IX. MCOMBO CUSTOMER SUPPORT

If for any reason, we have fallen short of your expectations, or if you have any questions and suggestions, please refer to the following contact information. We will do our best to work with you to make sure you are entirely satisfied.

Locations:

• DE: 2411 Bear Corbitt Rd STE 1, New Castle, DE, 19720
• TN: 3980 PREMIER AVE, MEMPHIS, TN, 38118
• CA: 2808 Vail Ave, Commerce, CA, 90040