TECNO CAMON 20 Pro User Manual
Know Your Phone
This section provides an overview of the TECNO CAMON 20 Pro's external features.
Front View:
- 1. Front camera
- 2. Volume + key
- 3. Volume - key
- 4. Power key
Back View:
- 5. NFC (Near Field Communication)
Explosion Diagram Specification
The following table lists the components of the TECNO CAMON 20 Pro:
| 1. FHD+ AMOLED | 2. MAIN FRAME MYLAR |
| 3. FRONT CAMERA FRAME | 4. CAM FF 32M |
| 5. REC | 6. HOMEMADE PCBA |
| 7. R CAM PARCEL CON FOIL | 8. CAM AF 64M |
| 9. CAM FF 2M | 10. REC CON FB |
| 11. BOLT SEAL FOAM | 12. CAM AI |
| 13. MAIN WATERPROOF FRAME | 14. SHIELD COP FOIL |
| 15. 2.5 SCREW | 16. 3.5 SCREW |
| 17. NFC | 18. FILM HOUSING |
| 19. BATTERY COVER | 20. GLA CAM LENS |
| 21. C-HOLDER | 22. GLA CAM LENS |
| 23. | 24. BOX SPK |
| 25. MI HSG PREDAWN | 26. RUBBER AUDIO JACK |
| 27. RUBBER USB | 28. ERM FPC |
| 29. BAT | 30. COA CABLE |
| 31. R VICECAM FRAME | 32. RAD FILM MAIN |
| 33. FPCA MAIN | 34. RUBBER LT SENSOR |
| 35. SMACORE | 36. BAT MYLAR |
| 37. PCBA SUB | 38. FPCA SIDEKEY |
| 39. F HSG ASM | 40. RAD FILM LCM |
| 41. HEAT PIPE |
SIM/SD Card Installation
- Power off the mobile device before proceeding.
- Refer to the following diagram for SIM and SD card installation:
Diagram Description: The diagram shows the front and back of the phone, with SIM and SD card trays depicted separately. The left side shows an SD card tray labeled 'SD'. The right side shows two SIM card trays labeled 'SIM 1' and 'SIM 2'.
Charging the Phone
You can charge your TECNO CAMON 20 Pro using a TECNO-approved charger or by connecting it to a computer via a USB cable (included with the phone).
Important: Use only TECNO chargers and cables. Using unauthorized chargers or cables may damage the device and void your phone's warranty.
Diagram Description: The diagram illustrates the phone being charged via its USB port. A close-up view shows the USB cable connected to the phone's charging port.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note on Radio Frequency Energy: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. These standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement: The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: CK7n (FCC ID: 2ADYY-CK7N) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.062W/kg, and when properly worn on the body is 0.489W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters, and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
