TECNO CAMON 20 User Manual
Explosion Diagram Specification
| 1 | FHD AMOLED | 2 | MAIN FRAME MYLAR |
| 3 | FRONT CAMERA FRAME | 4 | R CAM FRAME |
| 5 | FRONT ASSAY ASM | 6 | HOMEMADE PCBA MB |
| 7 | CAM FF 32M | 8 | REC PAD SBS GR |
| 9 | CAM AF 64M | 10 | R CAM PARCEL CON FOIL |
| 11 | FRONT CAM FILM | 12 | FP LMP FOAM |
| 13 | MAIN WATERPROOF FRAME | 14 | MC SCREW 25 |
| 15 | SHIELD COP FOIL | 16 | MACHINE SCREW 35 |
| 17 | NFC FILL FOAM | 18 | RAD FILM MI HOUSING |
| 19 | GB-COV ASM PREDAWN | 20 | CAM LENS RCAM 64M |
| 21 | CAM LENS RCAM 8W | 22 | SIM CARD HOLDER |
| 23 | SPEAKER HEAT FILM | 24 | BOX SPK |
| 25 | MID FRAME ASSAY | 26 | AUDIO JACK RUBBER |
| 27 | BAT BL | 28 | USB RUBBER |
| 29 | RUBBER LT SENSOR | 30 | USB FILM |
| 31 | RAD FILM MAIN | 32 | BAT MYLAR |
| 33 | COA CABLE | 34 | CAM FF 2M |
| 35 | FPCA SIDEKEY | 36 | CAM FF 8W |
| 37 | FPCA MAIN | 38 | RAD FILM LCM |
| 39 | HOMEMADE PCBA SUB | 40 | HEAT CON COPPER |
| 41 | REAR FLASH | 42 | ERM FPC |
| 43 | FP LINK FPC |
Know Your Phone
The TECNO CAMON 20 has the following components:
- 1. Front camera
- 2. Volume + key
- 3. Volume - key
- 4. Power key
- 5. NFC (Near Field Communication) module, typically located on the back of the phone.
Diagram Description: The diagram shows two views of the phone: a front view and a back view. The front view highlights the location of the front camera at the top center. The side view indicates the volume up/down buttons and the power button. The back view shows the camera module and the NFC indicator.
SIM/SD Card Installation
To install a SIM or SD card:
- Power off the mobile device.
- Refer to the provided diagrams for the correct placement of the SIM and SD cards. The diagrams show the front and back of the phone with the SIM tray indicated on the side.
Charging the Phone
You can charge your TECNO CAMON 20 using a charger or by connecting it to a computer via a USB cable. It is recommended to use only TECNO-approved chargers and cables to prevent device damage and warranty invalidation.
Diagram Description: The diagrams illustrate the process of connecting a USB cable to the phone's charging port, both from a side view and a close-up view.
FCC Caution
Labelling Requirements: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information: This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: CK6ns (FCC ID: 2ADYY-CK6NS) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.29W/kg and when properly worn on the body is 1.11W/kg.
Body-worn Operation: This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
