TECNO CAMON 20 Premier 5G User Manual
Explosion Diagram Specification
The following table details the components of the TECNO CAMON 20 Premier 5G:
| Item | Component | Item | Component |
|---|---|---|---|
| 1 | OLED | 2 | FC HEAT FILM |
| 3 | VC | 4 | MID COVER ASM RNM |
| 5 | ESD GD | 6 | CAMERA BRACKET |
| 7 | F CAM | 8 | UP SPK |
| 9 | MAIN PCBA | 10 | CABLE 1 |
| 11 | PS RUBBER | 12 | CABLE 2 |
| 13 | CAM CON FOAM | 14 | BAT FPC BTB RUBBER KC3 |
| 15 | 50M CON FOAM | 16 | LCD BTB RUBBER CK9N |
| 17 | PCBA P MYLAR | 18 | 108 CAM CON FOAM |
| 19 | 50 CAM CON FOAM | 20 | 108M CAM |
| 21 | 50M CAM | 22 | ELE LCD FPC FOAM B |
| 23 | LASER CON FOAM | 24 | 2M CAM |
| 25 | RCAM RUBBER 2M | 26 | SHIELDING HOT FLIM |
| 27 | LASER FPC | 28 | LASER SENSOR RUBBER |
| 29 | MCAM LENS DECO | 30 | REAR 50M CAM GLASS |
| 31 | REAR 108M CAM GLASS | 32 | FLASH FPC |
| 33 | FLASH CON FOAM | 34 | LOWHOUSING ASM |
| 35 | NFC | 36 | BATTERY COVER |
| 37 | LASER LAMPSHADES | 38 | FLASH LAMPSHADES |
| 39 | REAR 2M CAM GLASS | 40 | MIAN FPC |
| 41 | MOTOR | 42 | SIM PCBA |
| 43 | BATTERY | 44 | FINGERPRINT |
| 45 | REAR FINGERPRINT FOAM | 46 | USB PCBA |
| 47 | SIM TRAY | 48 | SCREWS |
| 49 | USB RUBBER | 50 | ANT PCB |
| 51 | VC MYLAR ASM | 52 | SPK BOX |
| 53 | RF CABLE CON CLOTH | 54 | SIDEKEY FPC |
| 55 | SIDEKEY VOICE FRAME | 56 | SIDEKEY POWER FRAME |
| 57 | POWER VOICE | 58 | SIDEKEY VOICE |
| 59 | SPK HOT FILM | 60 | REAR GRAPHITE |
Know Your Phone
This section identifies the key external components of the TECNO CAMON 20 Premier 5G:
- 1. Front camera
- 2. Volume + key
- 3. Volume - key
- 4. Power key
- 5. NFC (Near Field Communication) indicator location
The phone features a front camera at the top center of the display. The volume controls and the power button are located on the right side of the phone. The NFC component is located on the back of the phone.
SIM/SD Card Installation
To install a SIM or SD card:
- Ensure the mobile device is powered off.
- Refer to the diagrams for the correct placement of SIM and SD cards. The SIM tray is typically located on the side of the phone.
Charging the Phone
You can charge your TECNO CAMON 20 Premier 5G using a TECNO-approved charger and USB cable, or by connecting it to a computer via USB. Using unauthorized chargers or cables may damage the device and void the warranty.
The charging port is located at the bottom of the phone. A close-up view shows the USB port where the charging cable connects.
FCC Caution
Labelling Requirements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
RF Exposure Information:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information:
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: CK9n (FCC ID: 2ADYY-CK9N) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.123W/kg and when properly worn on the body is 0.540W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters, and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation:
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
