Altivar Soft Starter Fan Kits

Important Safety Information

DANGER: ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Only trained and qualified personnel familiar with the manual and product documentation should work on this equipment.
• Installation, adjustment, repair, and maintenance must be performed by qualified personnel.
• Verify compliance with all local and national electrical code requirements and regulations for grounding.
• Follow the instructions in the appropriate installation manual before performing work or applying voltage.

Failure to follow these instructions will result in death or serious injury.

CAUTION: SHARP EDGES

• Use necessary personal protective equipment (PPE), such as gloves, when working on or with this product.

Failure to follow these instructions can result in injury or equipment damage.

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. Schneider Electric assumes no responsibility for consequences arising from the use of this product.

© 2021 Schneider Electric. All Rights Reserved.

Fan Kit Installation - VZ3V481

Models: ATS480D32Y, ATS480D38Y, ATS48D32, ATS48D38

1. Step 1: Remove the front cover using a Torx T20 screwdriver. Arrows indicate removal direction.
2. Step 2: Insert the fan kit into the designated slot. Arrows indicate insertion direction.
3. Step 3: Secure the fan kit by pushing it until it clicks into place. A circular inset shows a close-up of the connection. A recycling symbol indicates proper disposal of packaging.
4. Step 4: Attach the fan kit, ensuring it is correctly seated. Arrows indicate attachment points. The model number VZ3V481 is shown.
5. Step 5: Connect the fan kit wiring. Arrows indicate connection points.
6. Step 6: Secure the fan kit with screws. Arrows indicate screw locations. Torque specification: 1.7 N.m (15 in-lb).

Fan Kit Installation - VZ3V4811, VZ3V482, VZ3V483

Models: ATS480D47Y, ATS480C17Y, ATS48D47, ATS48C17

1. Step 1: Remove the front cover using a Torx T20 screwdriver. Arrows indicate removal direction.
2. Step 2: Insert the fan kit into the designated slot. Arrows indicate insertion direction.
3. Step 3: Secure the fan kit by pushing it until it clicks into place. Circular insets show close-ups of the connection points. A recycling symbol indicates proper disposal of packaging.
4. Step 4: Attach the fan kit, ensuring it is correctly seated. Arrows indicate attachment points. Models VZ3V4811, VZ3V482, VZ3V483 are shown.
5. Step 5: Connect the fan kit wiring. Arrows indicate connection points.
6. Step 6: Secure the fan kit with screws. Arrows indicate screw locations. Torque specification: 1.7 N.m (15 in-lb).

Fan Kit Installation - VZ3V484

Models: ATS480C21Y, ATS480C32Y, ATS48C21, ATS48C32

1. Step 1: Remove the front cover using a Torx T20 screwdriver. Arrows indicate removal direction.
2. Step 2: Insert the fan kit into the designated slot. Arrows indicate insertion direction.
3. Step 3: Secure the fan kit by pushing it until it clicks into place. Circular insets show close-ups of the connection points. A recycling symbol indicates proper disposal of packaging.
4. Step 4: Attach the fan kit, ensuring it is correctly seated. Arrows indicate attachment points. Model VZ3V484 is shown.
5. Step 5: Connect the fan kit wiring. Arrows indicate connection points.
6. Step 6: Secure the fan kit with screws. Arrows indicate screw locations. Torque specification: 1.7 N.m (15 in-lb).

Fan Kit Installation - VZ3V485

Models: ATS480C41Y, ATS480C66Y, ATS48C41, ATS48C66, ATS480C79Y, ATS480M12Y, ATS48C79, ATS48M12

1. Step 1: Remove the top cover. Arrows indicate removal direction. Use Torx T25 screwdriver.
2. Step 2: Install the first fan module. Circular insets show mounting points.
3. Step 3: Install the second fan module. Circular insets show mounting points.
4. Step 4: Attach the fan modules. Arrows indicate attachment points. Model VZ3V485 is shown.
5. Step 5: Install the fan modules. Arrows indicate insertion direction. Model VZ3V485 is shown.
6. Step 6: Secure the fan modules with screws. Circular insets show mounting points. Torque specification: 3.5 N.m (31 in-lb).
7. Step 7: Connect the fan module wiring. Circular insets show connection points.
8. Step 8: Replace the top cover. Arrows indicate placement direction. Torque specification: 3.5 N.m (31 in-lb).