PHILIPS

1 Important Safety Instructions

Hearing Safety: Limit usage time at high volumes to prevent hearing damage. Set a safe volume level. The louder the sound, the less time you can listen safely.

Follow these recommendations:

• Listen for reasonable periods at reasonable volumes.
• Do not continuously increase volume; allow your hearing to adapt gradually.
• Do not turn up the volume so high that you cannot hear surrounding sounds.
• Be cautious or stop using if you are in potentially hazardous situations.
• Pressure from headphones/headsets may cause hearing loss.
• Avoid covering ears completely with headphones while driving, and be aware of local restrictions.
• Do not let music or phone calls distract you when walking or in other hazardous situations.

General Information - To prevent damage or malfunctions:

• Do not expose headphones to excessive heat.
• Do not drop headphones.
• Avoid liquid splashing or dripping onto headphones.
• Do not immerse headphones in water.
• Do not charge if the connector or socket is wet.
• Do not use cleaners containing alcohol, ammonia, benzene, or abrasives.
• Clean headphones regularly, especially sound outlets and microphone openings, with a soft, damp cloth. Prevent accumulation of earwax or dirt.
• If ear canals, air vents, or microphone openings have sweat or water, sound may temporarily decrease or be lost. This is not a malfunction. Dry the headphones thoroughly with a soft, damp cloth. Remove ear tips, point sound outlets downwards, and tap the headphones gently against a dry cloth 5 times to remove any water.
• Ensure headphones are completely dry before charging and use. Do not use alcohol wipes for cleaning.
• Do not expose the built-in battery to heat sources like sunlight or fire.
• Risk of explosion if battery is inserted incorrectly. Replace only with the same or equivalent type.
• Keep the charging port cover closed to maintain the ingress protection rating.
• Do not dispose of batteries in fire or hot ovens, or crush or cut batteries, as this may cause an explosion.
• Leaving batteries in an environment with extremely high temperature may result in explosion or leakage of flammable liquid or gas.
• Batteries subjected to extremely low air pressure may result in explosion or leakage of flammable liquid or gas.
• If a battery is replaced with an incorrect type, it may compromise a safeguard (e.g., in the case of some types of lithium batteries).
• If the headphones are not used for a long time, the rechargeable battery will gradually lose its capacity. To prevent this, charge the battery fully at least once every three months.
• For safety, the equipment should only be powered from a PS1 certified power source with an output not exceeding 15W.

Temperature and humidity for use and storage:

• Store in an environment with temperatures between -20°C and 50°C, and relative humidity up to 90%.
• Use in an environment with temperatures between 0°C and 45°C, and relative humidity up to 90%.
• Battery life may be shortened in extremely high or low temperatures.

2 Your ANC Noise-Cancelling True Wireless Headphones

Congratulations on your purchase and welcome to Philips! Register your product at www.philips.com/support to fully benefit from Philips support.

With these Philips ANC True Wireless Headphones, you can:

• Enjoy convenient wireless hands-free calls.
• Enjoy and control your music remotely.
• Switch between calls and music.
• Use the noise cancellation feature.

Package Contents

• Ear tips (3 pairs)
• Type-C charging cable (for charging only)

Other Devices

A mobile phone or device that supports Bluetooth and is compatible with the headphones (e.g., laptop, tablet, Bluetooth adapter, MP3 player, etc.).

General Overview of the ANC True Wireless Headphones

1. Multi-function sensor (MFT): Used for various controls.

2. Acoustic seal: Provides a good fit and sound isolation.

3. Touch screen: Displays information and allows interaction.

4. USB-C charging port: For charging the case.

5. Bluetooth pairing button / Reset button / Screen on/off: Used for pairing, resetting, and screen control.

3 Getting Started

Charging the Headphones

Note: Before using the headset, place it in the charging case and charge the battery for 2 hours for optimal battery capacity and lifespan.

Use only the original USB-C cable to charge to avoid damage.

If the headphones are not used for a long time, the rechargeable battery will gradually lose its capacity. To prevent this, charge the battery fully at least once every three months.

Charging Case

Connect the USB-C cable to the charging case and the other end to a power source.

Tip: A full charge using the USB cable takes approximately 2 hours (for headphones or charging case).

Wearing the Headphones

Choose the right ear tips for an optimal fit. A snug, secure fit ensures the best sound quality and noise cancellation.

1. Ensure the left or right headphone is inserted correctly.
2. Insert the headphone into your ear and twist slightly until it fits snugly.

The charging case serves as a portable reserve battery for the headphones. If the charging case is fully charged, it can charge the headphones 3 times fully.

Wearing the Headphones

1. Inserting the Headphones: Ensure the left or right headphone is inserted correctly.

2. Securing the Headphones: Insert the headphone into your ear and twist slightly until it fits snugly.

Downloading the App

Scan the QR code or tap "Download" to get the Philips Headphones app from the Apple App Store or Google Play Store. The Philips Headphones app allows you to control your music and adjust sound for calls and music to suit your needs.

Connecting

First-time Bluetooth Pairing:

1. Ensure the headphones are fully charged and turned off.
2. Open the charging case lid; the headphones will enter pairing mode and be ready to connect. The LEDs on both headphones will flash white and blue alternately. The headphones are now in pairing mode and ready to pair with your Bluetooth device (e.g., mobile phone).
3. Turn on the Bluetooth function on your Bluetooth device.
4. Pair the headphones with your Bluetooth device by referring to the device's user manual.

Note: If the headphones cannot find a previously paired Bluetooth device after powering on, put them into pairing mode (press and hold the button in the case for 3 seconds while both headphones are in the case and the lid is open). Bluetooth will automatically turn off after 3 minutes of inactivity. Actual time may vary depending on usage.

Multi-point Connection

Pairing

Pair the headphones with 2 devices, such as a mobile phone and a laptop.

Switching Between Devices

• You can listen to music from only one device at a time. The second device is reserved for phone calls.
• Stop the audio on one device and start playing audio on the other.

Note: If you are listening to audio from device 1 and receive a call on device 2, device 1 will be automatically paused. The incoming call will then be automatically directed to the headphones. When the call ends, music will automatically resume playing from device 1.

4 Using the Headphones

Connecting to a Bluetooth Device

1. Turn on the Bluetooth function on your Bluetooth device.
2. Open the charging case lid. The headphones will search for the last connected Bluetooth device and automatically reconnect. If the last connected device is not available, the headphones will search for the second connected device and reconnect.

Tip: If the Bluetooth function on your device turns on after connecting the headphones, go to your device's Bluetooth menu and manually connect the headphones to the device.

Note: Some Bluetooth devices may not connect automatically. In such cases, go to your device's Bluetooth menu and manually connect the headphones to the Bluetooth device.

ANC (Active Noise Cancellation) Control

Activating ANC Function

You can cycle through different ANC modes by double-tapping the left earbud.

• When the headphones are worn, the ANC function is automatically activated.
• Double-tap the MFT to turn off the ANC function.
• Double-tap again to switch to ambient sound mode.

Left Earbud: Double-tap for ANC ON/OFF/Ambient Sound.

Powering On/Off

Call and Music Control

Music Control

Call Control

Note: You will hear an audible alert when the volume reaches maximum level.

Voice Assistant

Task: Activate Voice Assistant (Siri/Google)

MFT: Left earbud

Action: Press and hold until you hear the voice prompt.

Headphone LED Indicator Status

5 Resetting the Headphones

If you encounter issues with pairing or connecting, follow the procedure below to reset the headphones to factory default settings.

1. On your Bluetooth device, go to the Bluetooth menu and remove "Philips TAT6000" from the list of devices.
2. Turn off the Bluetooth function on your Bluetooth device.
3. Place the headphones in the charging case and leave the lid open.
4. Press the button on the charging case twice.
5. Follow the steps in "Using the Headphones" under "Connecting your headphones to a Bluetooth device".
6. Pair the headphones with your Bluetooth device by selecting "Philips TAT6000".

If the headphones do not respond, perform the following step to reset the headphones:

• Place the headphones back into the charging case, open the lid, and press and hold the button on the case for 10 seconds.

6 Technical Specifications

• Music playback time (ANC on): 5 + 16 hours
• Music playback time (ANC off): 7 + 21 hours
• Charging time: 2 hours
• Lithium-ion battery: 50 mAh per earbud, 600 mAh for charging case
• Bluetooth version: 5.4
• Compatible Bluetooth profiles: HFP (Hands-free profile), A2DP (Advanced Audio Distribution Profile), AVRCP (Audio/Video Remote Control Profile)
• Supported audio codecs: SBC
• Frequency range: 2.4 – 2.4835 GHz
• Transmitter power: <10 dBm
• Operating range: Up to 10 meters
• Automatic power off
• USB-C port for charging
• Low battery warning: Yes
• 15 minutes of charging provides 2 hours of playback

Note: Technical specifications are subject to change without notice.

7 Notes

Declaration of Conformity

TP Vision Europe B.V. hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. The full text of the EU declaration of conformity is available at the following internet address: www.philips.com/support.

Disposal of Old Equipment and Batteries

Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused. The symbol on the product indicates that it is covered by the EU Directive 2012/19/EU. This symbol means that the product shall not be disposed of with other household waste at the end of its life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate it from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources. The symbol on the product or its packaging indicates that the product contains a battery covered by EU Regulation 2023/1542, which cannot be disposed of with normal household waste. Please familiarise yourself with the local system of separate collection for electrical and electronic products and batteries. Please comply with your local regulations and never dispose of the product and batteries together with normal household waste. Proper disposal of your old product and batteries will help prevent negative consequences for the environment and human health.

EMC Compliance

This product complies with all applicable standards and regulations regarding electromagnetic fields.

Environmental Information

• No excess packaging materials were used.
• The packaging can be separated into mono-material: paper and cardboard.
• Your system has been designed and manufactured with materials and components that can be recycled and reused by specialized companies. Follow local regulations for the disposal of packaging materials, depleted batteries, and old equipment.

Legal Compliance

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Canada

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-(B)/NMB-(B).

IC Radiation Exposure Statement

This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

8 Trademarks

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

Siri

Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

Google

Google and Google Play are trademarks of Google LLC.

9 Frequently Asked Questions

My Bluetooth headphones will not turn on.

The battery level is low. Charge the headphones.

My Bluetooth headphones will not pair with my Bluetooth device.

• Bluetooth is turned off. Turn on Bluetooth.
• Turn on Bluetooth on your device and select "Philips TAT6000".
• Turn off Bluetooth on all previously paired Bluetooth devices.
• Remove "Philips TAT6000" from your Bluetooth device's list.
• Pair the headphones (refer to "First-time Bluetooth Pairing" on page 8).

Pairing does not work.

• Place both headphones in the charging case.
• Ensure Bluetooth is turned off on all previously paired Bluetooth devices.
• Remove "Philips TAT6000" from your Bluetooth device's list.
• Pair the headphones (refer to "First-time Bluetooth Pairing" on page 8).

My Bluetooth device cannot find the headphones.

• The headphones may be connected to a previously paired device. Turn off the connected device or move it out of range.
• Pairing may have been reset, or the headphones may have been previously paired with another device. Re-pair the headphones as described in the user manual (refer to "Pairing with another Bluetooth device" on page 8).

My Bluetooth headphones connect to my mobile phone, but music plays only through the phone's speaker.

Refer to your mobile phone's user manual. Select the option to play music through the headphones.

Sound quality is low and there is static.

• Your Bluetooth device is out of range. Reduce the distance between the headphones and the Bluetooth device, or remove any obstructions.
• Charge the headphones.

Sound quality is low, very slow, or streaming does not work.

Ensure your mobile phone is compatible not only with HFP (mono) but also with A2DP and BT4.0x (or higher) technologies (refer to "Technical Specifications" on page 12).

Cleaning and Maintenance

Clean the headphones regularly, especially the sound outlets and microphone openings, with a soft, damp cloth. Prevent the accumulation of earwax or dirt.

If sweat or water remains in the sound outlets, air vents, or microphone openings, the sound level may temporarily decrease or be lost. This is not a malfunction. Dry the headphones thoroughly with a soft, damp cloth. Remove the ear tips, point the sound outlets downwards, and tap the headphones gently against a dry cloth 5 times to remove any water.

Ensure the headphones are completely dry before charging and use. Do not use alcohol wipes or similar items for cleaning.

Continuous Charging

Charge the headphones regularly. If the headphones are not used for a long time, the rechargeable battery will gradually lose its capacity. To prevent this, charge the battery fully at least once every three months.

© 2025 MMD Hong Kong Holding Limited. All rights reserved. Technical specifications are subject to change without notice.

Philips and the Philips Shield emblem are trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold by MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor with respect to this product. All other company and product names may be trademarks of their respective companies.