Fortin EVO-ONE THAR-ONE-TOY16 Installation Guide

Model: EVO-ONE

Date: 02/2019 | SN: 000000 00000 | Made in Canada © 2018 ALL RIGHTS RESERVED

Rev.: 20241128

Addendum - Suggested Wiring Configuration

Guide # 107591

Supported Vehicle Functions

Functions supported by this diagram (functional if equipped): Comfort Group, AUX.1, Immobilizer bypass (Lock, Unlock, Arm, Disarm, Trunk open, Horn, Parking Light, Tachometer, Power Lift Gate, Rear Defrost, Heated wiper, Heated Seats, Heated Mirrors), Door Status, Trunk Status, Hand-Brake Status, Foot-Brake Status, Hood Status*, Secure Takeover, OEM Remote monitoring.

Vehicle Compatibility

Vehicle: TOYOTA Sienna Hybrid

Years: 2021-2024

Compatible Module: EVO-ONE

Required: Manufactured after: 2019 | Firmware Version: 88.[33] Minimum

To add firmware version and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).

Programming Options

Immobilizer Bypass Option

Program bypass option: UNIT OPTION C1

Hood Pin Requirement

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

Vehicle hybrid only. Function A11: OFF (NON). If the vehicle can be remote started with the hood open, set function A11 to OFF.

Comfort Group Controls

Description: OEM Remote status (Lock/Unlock) monitoring, Hood trigger (Output Status), Push-to-Start, Push-to-Start Hybrid mode (Vehicle hybrid only). Comfort group controls functionnal.

Optional Function: Sliding Doors / Comfort Group Control

Feature 5: AUX+LOCK = Driver's side sliding door control. AUX+UNLOCK = Passenger's side sliding door control. (Comfort group control not functional)

Set to ON (OUI) for this feature.

Mandatory Installation Components

Hood Pin: The hood pin switch (included) must be installed. Set function A11 to OFF if the vehicle can be remote started with the hood open.

Security Sticker: Included. Installation of safety elements is mandatory.

WARNING: THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

Remote Starter Programming Options

Function 34

Mode: 2 | Description: TRUNK OUTPUT. Pulse 2.5 Seconds. (Trunk output: Unlock before trunk pulse 0.5 sec)

Function 39

Mode: 2 | Description: Temperature option: AUX.1 activated at 5°C, 5 seconds after remote started.

The vehicle's OEM remote and SmartKey remain operable during remote start.

Wiring Diagram Locations

ECU Locations

ECU, behind glove box: A

ECU, Driver's side: B

Connection Points

At Steering Column: C

(-)TRUNK: 3B

(-)HORN: 3

(~)IMI: 3A

(~)IMO: 3A

Wiring Connections

Main Harness Connections

Yellow In: AA11 | Purple Out: AA22 | Purple/White Out: AA33 | Green Out: AA44 | White Out: AA55 | Orange Out: AA66 | (-)Horn Orange/Black Out: AA77 | Dk.Blue Out: AA88 | Red/Blue In: AA99 | Lt.Blue/Black In/Out: AA1100 | Black In: AA1111 | Pink Out: AA1122 | (-)Trunk Release Yellow/Black Out: AA1133 | Brown/White In: AA1144 | HOOD PIN CONTACT Pink/Black In: AA1155 | Purple/Yellow In/Out: AA1166 | Green/White In/Out: AA1177 | Green/Red In/Out: AA1188 | White/Black Out: AA1199 | Lt.Blue In/Out: AA2200

Protection Circuits

Protect the main circuit with electrical tape to prevent short circuits. Use appropriate protection for power input.

Automatic Transmission Mode

CUT LOOP FOR AUTOMATIC TRANSMISSION MODE.

T-Harness Connections (THAR-TY120 / THAR-TOY16)

6 PIN REDCONN.

LT.BLUE/BLACK: BLEU PALE/NOIR | YELLOW/GREEN: JAUNE/VERT | YELLOW/RED: JAUNE/ROUGE | PURPLE/YELLOW: MAUVE/JAUNE

MALE VEHICLE PLUG

SIENNA HYBRID

FEMALE T-HARNESS PLUG

30-pin White MALE T-HARNESS PLUG

(-) HORN: Green | (-) TRUNK: Red | (~)IMI: Purple | (~)IMO: Green

30-pin White connector

MALE VEHICLE PLUG

40-pin White FEMALE T-HARNESS PLUG

Steering Column Connections

At switch, Black 14-Pin connector.

ECU, Driver's side Connections

Back view White 27-pin Connector ECU, Driver's side

Back view 54-Pin Black Connector ECU, Driver's side

ECU, behind passenger side glove box

Certification ECU/Smart Key ECU assembly located up behind passenger side glove box.

30-pin Tan MALE T-HARNESS PLUG

30-pin Tan connector

DCRYPTOR Programming Procedure

Parts Required (Not Included)

FLASH LINK UPDATER, FLASH LINK MOBILE, FLASH LINK MANAGER, or Microsoft Windows Computer with Internet connection. Smartphone Android or iOS with Internet connection.

Before Programming

Set the unit options and save.

Programming Steps:

Step 1-3: Module Initialization

Press and hold the programming button. Connect the 6-PIN Main harness (White connector). The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes. Release the programming button when the LED is BLUE (solid). If the BLUE LED is not ON solid, disconnect and repeat.

Step 4: Ignition ON

Press the Push-to-Start button twice to turn the ignition ON. The BLUE LED will flash rapidly.

Step 5: Ignition OFF

Press the Push-to-Start button once to turn the ignition OFF. The BLUE LED continues to flash rapidly.

Step 6: OEM Remote Unlock

Press the Unlock button on the vehicle's OEM remote. The BLUE LED will turn ON solid.

Step 7: Engine Start (First Time)

Press the foot-brake pedal. Press the Push-to-Start button until the engine starts. Release the foot-brake pedal. The BLUE LED will turn OFF. The RED LED will turn ON.

Step 8: Engine OFF (First Time)

Press the Push-to-Start button once to turn off the engine. The RED and YELLOW LEDs will alternate.

Step 9: Engine Start (Second Time)

Press the foot-brake pedal. Press the Push-to-Start button until the engine starts. Release the foot-brake pedal. The RED LED will turn OFF. The YELLOW LED will turn ON.

Step 10: Engine OFF (Second Time)

Press the Push-to-Start button once to turn off the engine. Wait. The RED and YELLOW LEDs will alternate.

Step 11: Disconnect

Disconnect all connectors, starting with the 6-Pin (Main Harness) or 4-Pin Data-link connector.

Step 12-13: Final Programming

Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the DCryptor menu. After programming is complete, reconnect the 6-Pin (Main Harness) or 4-pin (Data-Link) connector and then all remaining connectors.

The module is now programmed.

Remote Starter Verification Procedure

Test the remote starter. Remote start the vehicle.

Remote Starter Functionality

Remote Start Sequence

Start: All doors must be closed. Unlock the doors with the OEM remote, the remote-starter remote, or the proximity remote.

Remote start the vehicle: Enter the vehicle with the SMART-KEY. DO NOT PRESS THE BRAKE PEDAL. Press and release the Push-to-Start button once.

Driving the Vehicle

To drive: Press the brake pedal. The vehicle can now be put into gear and driven. If the Smart-Key is not detected, the vehicle will shut down.

Module Label Information

Model: EVO-ONE | Date: 02/2019 | FORTIN.CA | SN: 000000 00000 | Made in Canada © 2018 ALL RIGHTS RESERVED

Firmware and Guide Updates

Updated firmware and installation guides are posted regularly on the Fortin website (www.fortin.ca). It is recommended to update to the latest firmware and download the latest installation guide prior to installation.

Important Warnings and Disclaimers

WARNING: The information on this sheet is provided on an 'as is' basis without warranty of accuracy. The installer is solely responsible for checking and verifying any circuit before connecting. Only a logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes no liability for the accuracy or currency of the information supplied. Installation is the sole responsibility of the installer. FORTIN ELECTRONIC SYSTEMS assumes no liability for any type of installation. Neither the manufacturer nor distributor is responsible for damages caused by this module, except for replacement in case of manufacturing defects. This module must be installed by a qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com for the latest version.

Technical Support

Tel: 514-255-HELP (4357) | 1-877-336-7797

Addendum Guide