MEIKEE Motion Sensor Lights with 3 Adjustable Heads

Specifications

Installation Guide

1. Please inspect the product carefully before installation and use. If any parts are damaged or missing, contact MEIKEE for replacements.
2. Install the lamp at a point that can bear its weight. Turn off the power before wiring and installation.
3. Use lamps with the correct voltage as marked to ensure proper function.
4. Do not modify the lamp wire connections to avoid injury from electric leakage.
5. The waterproof rating is IP65; do not use the lamp in water as it may cause malfunction and electric leakage.

Component and Structure Diagrams

Main Components:

• LED lamp beads
• Front shell of lamp
• Back shell of lamp
• EVA mat
• Screws
• Motion sensor
• Fixing bar

Wiring:

• Live wire
• Neutral wire
• Ground wire

Installation Steps

1. Step 1: Attach the fixing bar to the junction box using two long screws.
2. Step 2: Remove the protective paper from the adhesive side of the EVA seal. Pull the power cord through the opening in the EVA seal and affix the EVA seal to the base of the lamp.
3. Step 3: Connect the ground wire of the lamp to the ground wire of the junction box (using a screw on the lower left foot of the fixing bar). Connect the neutral wire of the lamp to the neutral wire of the junction box, and the live wire of the lamp to the live wire of the junction box. Seal connections with electrical tape or connection terminals. WARNING: Ensure power is off before wiring.
4. Step 4: Use a long screw to pass through the center hole of the lamp and connect it to the center hole of the fixing bar.
5. Step 5: Adjust the direction and detection range of the light as needed. The detection range is approximately 180° horizontally and 90° vertically for each head.
6. Step 6: Adjust the TIME and LUX dials on the sensor according to your needs.
   TIME setting: Controls lighting duration (0-600 seconds).
   LUX setting: Controls sensitivity to ambient light (Daytime mode: works 24 hours; Night mode: works only at night).
   SENS setting: Controls detection distance (0-12 meters).
7. Step 7: Installation is complete. Power on the light.

Motion Sensor Settings

Motion Sensor A

Timing Settings:

• 10S (Lighting for 10 seconds)
• 45S (Lighting for 45 seconds)
• 120S (Lighting for 120 seconds)
• 600S (Lighting for 600 seconds)

Sensing Distance Settings:

• 8M (Sensing distance: 5-8m)
• 12M (Sensing distance: 8-12m)

Mode Settings:

• Daytime mode: The motion sensor works during both day and night (24 hours).
• Night mode: The motion sensor only works at night.

Motion Sensor B

Timing Settings:

• 10S (Lighting for 10 seconds)
• 45S (Lighting for 45 seconds)
• 90S (Lighting for 90 seconds)
• 180S (Lighting for 180 seconds)

Sensing Distance Settings:

• 5M (Sensing distance: 0-5m)
• 8M (Sensing distance: 5-8m)
• 12M (Sensing distance: 8-12m)

Mode Settings:

• Daytime mode: The motion sensor works during both day and night (24 hours).
• Night mode: The motion sensor only works at night.
• Keep on at night: The light remains on continuously at night, unaffected by motion detection.

Motion Sensor C

Timing Settings:

• 10S (Lighting for 10 seconds)
• 45S (Lighting for 45 seconds)
• 120S (Lighting for 120 seconds)
• 600S (Lighting for 600 seconds)

Mode Settings:

• Daytime mode: The motion sensor works during both day and night (24 hours).
• Night mode: The motion sensor only works at night.

Motion Sensor D

Timing Settings:

• 10S (Lighting for 10 seconds)
• 45S (Lighting for 45 seconds)
• 120S (Lighting for 120 seconds)
• 600S (Lighting for 600 seconds)

Mode Settings:

• Daytime mode: The motion sensor works during both day and night (24 hours).
• Night mode: The motion sensor only works at night.

Important Notes

Detection Distance: The detection distance is influenced by ambient temperature. If the ambient temperature is close to or higher than body temperature, the detection distance will be shorter. Conversely, if the ambient temperature is lower, the detection distance will be farther.

Routine Maintenance

1. Clean the lamps regularly to ensure normal operation.
2. Always turn off the power before performing any maintenance.
3. Do not use chemicals to clean the lamps to avoid damage.

Contact Information

C&E Connection E-Commerce (DE) GmbH
EC REP: Zum Linnegraben 20, 65933, Frankfurt am Main, Germany
Email: info@ce-connection.de
Tel: +49 (069) 27246648

Manufacturer: Shenzhen Oumeike Lighting Technology Co., Ltd.
Address: No. 19-20, Anye Road, Yuanshan Street, Longgang District, Shenzhen, Guangdong, China
Tel: +86 0755-28608199

MEIKEE Customer Support:
Email: meikee@meikeelighting.com
Website: http://www.meikeelighting.com

Compliance and Certifications

The product complies with FCC, CE, RoHS standards and has an IP65 waterproof rating.