MEIKEE RGB Floodlight
User Manual and Installation Guide
Introduction
Thank you for purchasing MEIKEE products. To ensure a better experience, please follow the instructions step by step.
This document provides comprehensive information for MEIKEE RGB Floodlights, RGB Strahler (Spotlights), and Proiettore RGB (Projectors), covering installation, operation, and maintenance.
Product Specifications
| Model | Power (W) | Lumen (DW) | Installation Height | Lighting Range (180°) |
|---|---|---|---|---|
| RFLB025 | 25W | 2000 | 3.5-5M | 3-4M |
| RFLB035 | 35W | 2800 | 3.5-5M | 4-6M |
| RFLB042 | 42W | 3350 | 5-7M | 4-6M |
| RFLB060 | 60W | 4800 | 5-7M | 6-8M |
| RFLB100 | 100W | 8000 | 7-10M | 10-12M |
| RFLB150 | 150W | 12000 | 10-12M | 10-12M |
Input Voltage: US: AC 120V/60HZ; EU/UK: AC 230V/50HZ
Wavelength: R: 620-625NM, G: 520-525NM, B: 460-462NM
IP Rating: IP66 (Rainproof)
Operating Temperature: Ta: -25~40℃
Components
The floodlight comprises the following parts:
- ① Shell of flood light
- ② Lighting units
- ③ Reflector
- ④ Glass mask / PC cover
- ⑤ Trestle (Mounting Bracket)
- ⑥ Power Plug
- ⑦ Screws
[Diagram illustrating the floodlight assembly with numbered components.]
Installation Guide
- Step 1: Drill two mounting holes in the wall or ground, ensuring the spacing matches the bracket's screw holes.
- Step 2: Position the bracket onto the prepared holes. Secure it firmly with the provided screws and adjust the angle for optimal light direction. [angle adjustment]
- Step 3: Connect the power plug to a suitable outlet and switch on the power. Verify the product is functioning correctly. Install batteries into the remote control and select your desired lighting mode.
[Diagram illustrating the three installation steps.]
Features and Remote Control Operation
The MEIKEE floodlight features an integrated RF receiver, enabling wireless control from up to 12 meters away. [signal strength indicator]
Remote Control Functions:
- OFF: Turns the light off.
- ON: Turns the light on.
- Brightness Up/Down: Adjusts light intensity through 6 levels (25% to 100%). [Up arrow] / [Down arrow]
- Color Selection: RR (Red), GG (Green), BB (Blue), WW (White).
- FLASH: Activates a rapid color-changing mode (R+G+B cycle). Press the button to control the speed of the color transitions. [Fast forward]
- SMOOTH: Activates a slow, gradual color-changing mode. Press the button to adjust the speed of the color transitions. [Gradual change]
- Timing Function (2H/4H/6H): Select a desired timer duration (2, 4, or 6 hours). The light will automatically switch off after the set time. Pressing a timing key will cause the indicator light to flash twice, confirming the timer has started. [Timer]
Memory Function: The light retains its last set color and mode when powered off and on again.
[Diagram showing the remote control layout and button functions.]
Troubleshooting Common Issues
If the floodlight is not functioning as expected, please review the following potential causes:
- No Power/Light: Ensure the remote control is pointed towards the floodlight and the "ON" button has been pressed. Verify that the input voltage supplied matches the product's requirements.
- Incorrect Voltage: For voltage compatibility issues, consult a qualified electrician to confirm the power supply voltage meets the specifications of the MEIKEE floodlight.
- Unresolved Problems: If the issue persists after attempting these solutions, discontinue use and contact a professional electrician or MEIKEE customer service for further assistance.
Routine Maintenance
- Periodically clean the floodlight to maintain optimal performance and brightness. [Cleaning]
- Always disconnect the power supply before commencing any cleaning or maintenance procedures. [Power Off]
- Avoid using chemical cleaning agents, as they may damage the lamp's components.
Important Warnings and Safety Information
- The LED module is an integrated component and cannot be replaced. If it becomes damaged or reaches the end of its lifespan, the entire fixture must be replaced.
- Any damage to the wiring renders the lamp unusable and requires disposal.
- If the product casing is compromised or water ingress occurs, the lamp is no longer safe for use and must be scrapped.
- Avoid prolonged direct viewing of the LED light-emitting surface to prevent potential eye strain or damage. [Eye protection]
- Never cover the luminaire with thermal pads or similar materials, as this can lead to overheating.
- The IP66 rating signifies resistance to dust and high-pressure water jets, suitable for rain protection. However, the lamp is not designed for submersion in water, which could lead to electrical leakage.
- Professional installation by a qualified electrician is recommended for all MEIKEE floodlights.
Customer Support
For any inquiries or assistance regarding MEIKEE products, please reach out to our customer service team:
E-mail: meikee@meikeelighting.com
Our dedicated support team is committed to providing timely assistance and resolving any product-related concerns.
