PowerWalker VI STL Series UPS User Manual
Overview
This manual provides instructions for the PowerWalker VI STL series of Uninterruptible Power Supplies (UPS), covering models 600, 800, 1000, 1200, 1500, and 2200.
The UPS offers automatic voltage regulation for unstable power grids and battery backup during power outages, ensuring stable power for your computer system.
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation.
- WARNING! To prevent risk of fire or electric shock, install the UPS indoors in a temperature and humidity controlled environment, free from conductive contaminants. (Refer to specifications for acceptable temperature and humidity ranges).
- WARNING! To reduce the risk of UPS overheating, do not cover the UPS cooling vents, expose it to direct sunlight, or install it near heat-emitting appliances such as heaters or stoves.
- WARNING! Do not connect non-computer related items such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to the UPS.
- WARNING! Do not connect the UPS input to its own output.
- WARNING! Do not allow liquid or any foreign objects to enter the UPS. Do not place drinks or any other liquid containers on or near the unit.
- WARNING! In case of emergency, press the OFF button and disconnect the power cord from the AC mains to properly shut down the UPS.
- WARNING! Do not connect an extension cord or surge suppressor to the UPS.
- WARNING! Disconnect from mains before cleaning and do not use liquid or aerosol cleaners.
- WARNING! Battery servicing should be performed by or supervised by personnel knowledgeable about batteries and the necessary precautions. Keep unauthorized persons away from batteries.
- WARNING! If maintenance or repair work is required inside the UPS, disconnect the positive and negative battery terminals at the quick-disconnect connectors.
- WARNING! Internal battery voltage is 12V DC. Sealed, lead-acid, 6-cell battery.
- WARNING! When replacing batteries, use batteries of the same quantity and type.
- WARNING! Do not dispose of batteries in a fire. The battery may explode. Do not open or damage the battery or batteries. Leaked electrolyte is harmful to skin and eyes.
UPS System Installation
Unpacking
The box should contain the following:
- (1) UPS Unit x1
- (2) User Manual x1
Your new UPS can be used immediately upon receipt. However, to achieve maximum battery charge capacity, it is recommended to charge it for at least 8 hours. Charge loss may occur during transport and storage. To charge the battery, simply leave the unit plugged into an AC outlet. The unit will charge whether it is turned on or off.
Basic Operation
Front Panel
The front panel features:
- 1. LCD Display: Displays UPS status, including input voltage, output voltage, battery charge percentage, and load percentage, etc.
- 2. Power Switch: Press and hold the switch for 2 seconds to turn the UPS on or off.
- 3. LED Indicators:
LCD Brightness Setting: The auto-brightness function can be turned on/off by holding the button for 10 seconds. By default, the LCD auto-brightness function is off.
Back Panel
The back panel features:
- 1. USB COMM. Port: This port allows connection and data exchange from your computer's USB port to the UPS.
- 2. RJ45/11 Communication Protection Ports: Communication protection ports will protect any standard modem, fax, telephone line, or network cable.
- 3. Input Circuit Breaker: The circuit breaker provides optimal overload protection.
- 4. Input Power Cord: Connects to the mains power supply.
- 5. Battery Backup and Surge Protected Outlets: Provide battery backup power and surge protection. Supply power to connected equipment for a period of time during a power failure.
Diagram Description (Front Panel): The front panel displays an LCD screen for status information, a power switch, and LED indicators.
Diagram Description (Back Panel): The back panel shows the input power cord, circuit breaker, USB communication port, RJ45/11 communication ports, and battery backup/surge protected outlets.
Technical Specifications
| Model | VI 600 STL | VI 800 STL | VI 1000 STL | VI 1200 STL | VI 1500 STL | VI 2200 STL |
|---|---|---|---|---|---|---|
| Capacity (VA/W) | 600/360 | 800/480 | 1000/600 | 1200/720 | 1500/900 | 2200/1320 |
| Input | ||||||
| Voltage Range | 162 ~ 290 VAC | |||||
| Nominal Frequency | 50/60 Hz | |||||
| Output | ||||||
| Output Voltage (Battery Mode) | Simulated Sine Wave at 230 VAC +/-10% | |||||
| Output Frequency (Battery Mode) | 50/60 Hz +/- 1% | |||||
| Overload Protection | Circuit breaker / Fuse | |||||
| Dimensions (W x H x D) (mm) | 96 x 138 x 286 | 148 x 178 x 298 | ||||
| Battery | Sealed maintenance-free lead-acid battery | |||||
| Battery Type | 12V 7AH x1 | 12V 7.2AH x1 | 12V 9AH x1 | 12V 7AH x2 | 12V 7.2AH x2 | 12V 9AH x2 |
| Typical Recharge Time | 8 hours | |||||
| Indicators | Power On, Low Battery, Overload, Fault | |||||
| Audible Alarms | Yes | |||||
| Environment | ||||||
| Operating Temperature | 0°C to 40°C | |||||
| Operating Relative Humidity | 0 to 90% (Non-condensing) | |||||
| Management | ||||||
| Auto-charging | Yes | |||||
| Auto-restart | Yes | |||||
| Communication Ports | USB COMM. Port (HID support), RJ45/11 Protection Ports | |||||
LED Indicator Definitions
The UPS uses various indicators to show its status:
- PV AC BATT. INPUT: Displays AC input voltage.
- OUTPUT: Displays output voltage.
- BATT. (%): Displays battery charge level.
- LOAD (VA/KW/Hz): Displays load percentage or frequency.
Indicator States:
- Battery Charging: Cyclic lighting [battery icon].
- Battery Fully Charged: Solid light [battery icon].
- Line Mode: Normal operation on mains power.
- Battery Mode: Operation on battery power.
- Mute: Audible alarms can be muted or unmuted by double-pressing the power switch quickly. By default, audible alarms are ON.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| UPS does not provide expected runtime | Batteries are not fully charged. Battery is slightly worn. | Charge the battery by leaving the UPS on. Contact technical support. |
| UPS does not turn on. | The ON/OFF switch is designed to prevent damage by quickly turning off and on. The unit is not connected to an AC outlet. Battery is discharged. | Turn off the UPS. Wait 10 seconds, then turn the UPS on. The unit must be plugged into a 230V AC 50/60 Hz outlet. Contact technical support. |
| Outlets do not provide power to equipment | Mechanical problem. Circuit breaker tripped due to overload. Batteries are discharged. | Contact technical support. Turn off the UPS and disconnect at least one unit of connected equipment. Disconnect the UPS power cord, then push the circuit breaker handle. Allow the unit to recharge for at least 4 hours. Contact technical support. |
| Fault Code F09 | Batteries are discharged. | Turn off the computer and charge the battery immediately. |
| Fault Code F12 | Unit is damaged by a voltage surge or overvoltage. | Contact technical support. |
| Fault Code F13 | Output Short: Output circuit short-circuit. | Turn off the UPS. There may be problems with the connected equipment, disconnect it and check again. |
| Fault Code F14 | Battery voltage is too low. Battery is overcharged. | Contact technical support. |
| Overload Condition: Your equipment requires more power than the UPS can provide. It will shut down. | Turn off secondary equipment. If this resolves the overload problem, the UPS will return to normal operation. |
PowerMaster+ Management Software
The PowerMaster+ management software provides a user-friendly interface for managing your power systems. The graphical user interface is intuitive and displays essential power supply information at a glance.
Installation Procedure:
- Download PowerMaster+ from the website: http://powermaster.powerwalker.com/
- Double-click the file and follow the installation instructions.
After the computer restarts, the Power Master+ program will appear as a blue icon in the system tray.
Certifications and Compliance
The UPS complies with relevant safety and environmental standards. Look for symbols like:
- [CE certified]
- [Contains lead battery]
- [Recyclable]
