Home Decorators Collection 4-Light Chandelier

Introduction

Thank you for choosing the Home Decorators Collection 4-Light Chandelier. We appreciate your trust and strive to create quality products designed to enhance your home. Visit us online to see our full line of home improvement products.

Safety Information

Read all instructions before assembling and installing the product.

Consult a qualified electrician for installation of this fixture.

For non-electrical questions, contact Customer Service at 1-800-986-3460 or visit WWW.HOMEDEPOT.COM/HOMEDECORATORS.

Save these instructions for future reference.

⚠️ DANGER: Risk of electrical shock. Disconnect power before installation.

ℹ️ IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not continue assembly. Call Customer Service at 1-800-986-3460.

Warranty

Limited Warranty

What is Covered: The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for three (3) years from the date of purchase. This warranty applies to the original consumer purchaser for normal use. The manufacturer's obligation is limited to repair or replacement of defective products, provided the product has not been damaged through misuse, abuse, accident, modification, alteration, neglect, or mishandling.

What is Not Covered: This warranty does not apply to products that are improperly installed, set-up, or used contrary to instructions. It also does not cover failures due to accident, misuse, abuse, negligence, alteration, faulty installation, or issues not related to faulty material or workmanship. Surface discoloration or weathering is considered normal wear and tear and is not covered. The manufacturer disclaims warranties of fitness for a particular purpose and is not liable for consequential or incidental loss or damage, including labor or expense costs for replacement or repair.

Contact Customer Care at 1-800-986-3460 or visit WWW.HOMEDEPOT.COM/HOMEDECORATORS.

Pre-Installation

Planning Installation

Read all instructions before assembly and installation. To avoid damaging the product, assemble it on a soft, non-abrasive surface like carpet or cardboard. Inspect each part for shipping defects. Keep your receipt and these instructions for proof of purchase.

Tools Required

The following tools are needed for installation:

• Safety goggles
• Measuring tape
• Phillips screwdriver
• Flathead screwdriver
• Wire strippers
• Wire cutters
• Ladder
• Electrical tape
• Pliers

Hardware Included

Note: Hardware is not shown to actual size.

Components:

• AA Wire Nut (3)
• BB Single Crossbar (1)
• CC Hex Nut (1)
• DD Outlet Box Screw (2)
• EE Green Ground Screw (1)
• FF Nipple (1)
• GG Chain Link (2)
• HH Canopy (1)
• II Canopy Loop (1)
• JJ Loop Ring (1)
• KK Chain (1)
• LL Candle Sleeve (4)
• MM Tooth Washer (1)

Package Contents

The following parts are included in the package:

• A Fixture Loop (1)
• B Top Arm (1)
• C Washer (2)
• D Crystal Bobeche (1)
• E String Shade (1)
• F Fixture Body (1)
• G Crystal Strand G (12)
• H Crystal Strand H (1)

A diagram shows the chandelier assembly with parts labeled A through H.

Installation

Step 1: Assembling the Fixture Body

Pull the fixture wire and ground wire up through the washers (C), Crystal Bobeche (D), Top Arm (B), and Fixture Loop (A).

Insert the String Shade (E) between the bottom washer (C) and the Fixture Body (F).

Fasten the Fixture Loop (A) to the nipple of the Fixture Body (F).

A diagram illustrates this assembly process, showing parts A, B, C, D, E, and F.

Step 2: Installing the Single Crossbar

WARNING: Turn the power off at the main fuse box before installation.

Thread the Nipple (FF) into the Single Crossbar (BB) and secure with a Tooth Washer (MM) and Hex Nut (CC). Adjust the length of the Nipple (FF) if necessary.

Attach the Single Crossbar (BB) to the junction box (not included) with the two Outlet Box Screws (DD).

A diagram shows the crossbar (BB) being attached to the junction box with screws (DD), with the nipple (FF), washer (MM), and nut (CC) in place.

Step 3: Adjusting the Chain Length

Shorten the Chain (KK) length to your desired hanging height. Use pliers (not included) to pull open a chain link at each end of the section to be removed.

Unlink the unwanted section by unhooking the opened link from the remaining chain.

Use pliers to reclose the opened chain link.

NOTE: When adjusting the chain length, use a soft cloth between the pliers and the chain links to avoid damaging the chain's finish.

A diagram illustrates using pliers to open and close a chain link (KK).

Step 4: Attaching the Chain

Attach the Canopy Loop (II) to the Nipple (FF).

Pass the Chain (KK) through the Canopy (HH) and the Loop Ring (JJ).

Attach one end of the Chain (KK) to the Canopy Loop (II) and the other end to the Fixture Loop (A) using a Chain Link (GG).

Pull the fixture wire and ground wire up from the Fixture Loop (A), through the Chain Link (GG), alternating links of the Chain (KK), the Loop Ring (JJ), Canopy (HH), another Chain Link (GG), the Canopy Loop (II), and the Nipple (FF) into the outlet box.

A diagram illustrates the chain attachment and wire routing.

Step 5: Making Electrical Connections and Locking the Canopy

NOTE: Always use Wire Nuts (AA) to connect wires and push all excess wires and connections back into the junction box.

Connect the ground wire from the branch circuit to the Green Ground Screw (EE) on the Single Crossbar (BB).

Connect the fixture wires as follows:

• Ribbed Brown wire (from fixture) to White wire (from house).
• Smooth Brown wire (from fixture) to Black wire (from house).
• Ground wire (from fixture) to Ground screw or Ground wire (from house).

Cover the three connections using the three Wire Nuts (AA). Wrap the wire connections with electrical tape for a more secure connection.

Move the Canopy (HH) up and over the outlet box (not included). Secure the canopy by tightening the Loop Ring (JJ) onto the Canopy Loop (II).

A diagram shows the electrical connections and canopy attachment.

Step 6: Installing the Bulbs

Insert the Candle Sleeves (LL) onto each socket of the Fixture Body (F).

Install the 60W max CA10 E12 Bulbs (not included) into each socket of the Fixture Body (F).

A diagram shows candle sleeves (LL) being inserted onto sockets on the fixture body (F).

Step 7: Attaching the Crystal Strands

Referring to the crystal strands distribution diagram, carefully attach the Crystal Strands (G & H) to the hooks and holes found on the Top Arm (B) and the Fixture Body (F), as indicated.

A diagram shows the placement of crystal strands (G and H) on the chandelier.

An illustration shows the fully assembled fixture.

Care and Cleaning

Clean the light fixture carefully with a soft, dry cloth. Do not use any cleaner with chemicals, solvents, or harsh abrasives.

Troubleshooting

Problem: The bulb will not light.

Possible Cause: The bulb is burned out.

Solution: Replace the light bulb.

Possible Cause: The power is off.

Solution: Ensure that the power supply is turned on.

Possible Cause: The circuit breaker is off.

Solution: Ensure that the circuit breaker is set to the ON position.

Problem: The fuse blows or the circuit breaker trips when the light is turned on.

Possible Cause: There are too many items on one circuit.

Solution: Unplug the other items on the circuit. Contact a qualified electrician or call the Customer Service Team at 1-800-986-3460.