LED FLUSH MOUNT KIT USER MANUAL
12-24VDC
CONTENTS
- LIGHTHEAD x 2pcs
- MOUNTING GROMMET x 2pcs
- EXTENSION CABLE
- LED CONTROLLER
WIRING & FUNCTIONS
To Chassis Ground: BLACK
To +VDC: RED (Fuse Rating 12V@3A / 24V@2A)
For Low Power Warning: WHITE (Apply +VDC to WHITE wire while RED wire is activated for Low Power Operation.)
For Synchronization and Flash Pattern: YELLOW (Connect YELLOW wires of all kits together for synchronization. All kits should be set to the same pattern) *Actual approval will be based on the model purchased.
The LED Controller connects to the 2nd Lighthead via the extension cable. Ensure all unused bare wires are covered.
OPERATION
For Simultaneous or Alternating Synchronization:
- Apply +VDC to RED and YELLOW wires simultaneously to enter Flash Mode Selection.
- Remove YELLOW wire from +VDC and momentarily apply to +VDC to change mode selection:
- Mode 1 = Head 1 & 2 flash alternately
- Mode 2 = Head 1 & 2 flash simultaneously
- Exit Flash Mode Selection by removing +VDC.
For Flash Pattern Selection:
- Momentarily apply +VDC to YELLOW wire: Once to next pattern.
- Quick three times to FP#1 (see Flash Pattern Chart).
Flash Patterns
| FP# | Flash Patterns |
|---|---|
| 1 | Single [2Hz] |
| 2 | Double [R65]* |
| 3 | Triple [2Hz] |
| 4 | Quad [2Hz] |
| 5 | Random |
| 6 | Single |
| 7 | Double |
| 8 | Quad |
| 9 | Quint |
| 10 | Mega |
| 11 | Ultra |
| 12 | Single-Quad |
| 13 | Single H/L |
| 14 | Steady or Steady Double** |
* Actual approval will be based on the model purchased.
** In Mode 2, lightheads will both steady-burn; in Mode 1, one lighthead will steady burn while the other does double flash.
INSTALLATION - FLUSH MOUNT
- Select a mounting location and drill one 1" (25.4mm) cut-out. NOTE: Mounting surface thickness is approximately 0.8~2.0mm.
- From the front, install the MOUNTING GROMMET onto the cut-out, and then insert the LIGHTHEAD.
- Ensure that the triangle mark on the lens is aligned vertically. NOTE: Optical stripes must align vertically to meet approved regulation.
- Where necessary, apply silicone around the reverse side to prevent from rotating.
INSTALLATION - BRACKET MOUNT (sold-separately)
- From the front, install the MOUNTING GROMMET onto the BRACKET, and insert the LIGHTHEAD.
- Ensure that the triangle mark on the lens is aligned vertically. NOTE: Optical stripes must align vertically to meet approved regulation.
- Secure the LIGHTHEAD onto the BRACKET with a screw (M3 x 8mm).
- Secure the BRACKET onto the desired mounting surface with screws (#6 x 18mm).
WIRING 2 KITS TOGETHER
The following schematic diagram illustrates wiring two kits together. The YELLOW wires from both controllers must be connected together for synchronization.
- If Mode 1 is selected: Head 1A & 2A will flash alternately with Head 1B & 2B.
- If Mode 2 is selected: All Heads will flash simultaneously.
* Refer to Flash Pattern Chart on the opposite page.
NOTE: To achieve alternating patterns between Head 1A & 2B with 1B & 2A, simply reverse the lighthead outlets on one of the Controllers (both kits must be in Mode 1).
The diagram shows connections for two units. Each unit controller has connections for BLACK (to GND), RED (to +VDC, with a 12V@3A / 24V@2A fuse recommended, user-supplied), WHITE (for ON/OFF control), and YELLOW (for synchronization). Extension cables are used to connect to the lightheads.
NOTE: The mounting area varies from vehicle to vehicle. The diagram is not drawn to scale.
