1. Installation Overview
This section provides an overview of the approved installation process for the Honeywell DUAL TEC® Motion Sensor. Ensure the installation area is clear and unobstructed.
Key Installation Steps:
- Mounting Location: Position the sensor to cover the desired area.
- Wiring: Connect the sensor to the alarm system.
- Cover Closure: Secure the sensor cover.
Placement Guidelines:
- Maintain a clear area around the sensor.
- Avoid obstructions.
- Recommended mounting height: 2.1 - 2.7 meters (7' - 9').
- Optimal mounting height for look-down coverage: 2.3 meters (7' 6").
2. Mounting and Wiring
This section details the physical installation and electrical connections.
Mounting:
- Use 3.5 mm x 30 mm (#6 x 1 1/4") screws for mounting. Screws are not included.
- The sensor can be mounted directly to a wall or in a corner.
Wiring Connections (Terminal Block):
| Terminal | Description | Specifications |
|---|---|---|
| LED | LED Indicator | |
| TBL | Tamper Bypass Link | |
| T | Tamper Input | |
| C | Common Ground | |
| NC | Normally Closed Output | |
| V- | Negative Power Supply | 0 VDC |
| V+ | Positive Power Supply | 9-15 Vcc/VDC |
Power Consumption:
- Standby: 1.8 mA max
- Alarm: 11 mA (14 mA max)
EOL Resistors:
- EOL resistors (25 Vcc/VDC, 30 mA) are used for Alarm, Tamper, and AM/Fault circuits.
3. End-of-Line (EOL) Resistance Settings
Configure the EOL resistances using the DIP switches for Alarm, Tamper, and AM/Fault circuits.
EOL Resistance Values (kOhm):
- Position 1: 1 kOhm
- Position 2: 2.2 kOhm
- Position 3: 4.7 kOhm
- Position 4: 5.6 kOhm
The DIP switches allow selection of these values for each circuit.
4. Anti-Mask and Sensitivity Adjustment
The sensor features anti-masking capabilities and adjustable microwave sensitivity.
Anti-Mask (AM) Settings:
- AM Enabled: ON position.
- AM Disabled: OFF position.
- The AM LED indicates anti-mask status.
Microwave (MW) Range Adjustment (Sensitivity):
- Adjust sensitivity from MIN to MAX.
- Note: When set to minimum, the sensor range is reduced to 5 meters.
Factory Default Settings:
The sensor is pre-configured with factory default settings for optimal performance.
5. Walk Test Procedure
Perform a walk test to verify sensor operation and coverage.
Walk Test Reset:
- Hold the walk test button for 1/2 second, 4 times.
- The AM LED will indicate the walk test mode.
LED Indicators during Walk Test (10 min duration):
| LED Color | Power Up | Walk Test (10 min) | Normal | Trouble | Anti-Mask |
|---|---|---|---|---|---|
| Red | Slow Blink | ON Alarm | ON Alarm | Fast Blink | Fast Blink |
| Yellow | OFF | ON Microwave | OFF | OFF | Fast Blink |
| Green | OFF | ON PIR | OFF | OFF | OFF |
6. Coverage Patterns
The sensor provides comprehensive coverage, detailed in the plan and side views.
Plan View (All Zones):
- Detection zones extend up to 12 meters (40 feet) from the sensor.
- Zones are distributed symmetrically from the center.
Side View:
- Look-down Zone (A): Covers the area directly beneath the sensor.
- Lower Zones (B): Short-range detection.
- Intermediate Zones (C): Mid-range detection.
- Long-range Zones (D): Extends up to 16 meters (53 feet) at a height of 2.3 meters (7'6").
7. Approval Listings and Compliance
The Honeywell DUAL TEC® Motion Sensor complies with various international standards.
Certifications:
- EN50131-2-4:2008: Security Grade 3, Environmental Class II. Suitable for connection to an EN 60950 Class II Limited Power Source.
- NF&A2P (France): 3 shields (NF324-H58) compliant with EN50131-2-4 and RTC50131-2-4. IP30 IK04.
- DT8016AF4 Certificate N°: 2831420015
- DT8016AF5 Certificate N°: 2821420015
- Certification Body: CNPP Cert. (www.cnpp.com) and AFNOR Cert. (www.marque-nf.com).
- INCERT (Belgium): B-893-0012 (for DT8016AF4).
Important Note for EN 50131-2-4 Compliant Installations:
- Mount the sensor at 2.3m.
- Do not use only the right side corner mounting holes.
- Enable look-down feature.
- Set microwave sensitivity to maximum.
- Lock the sensor housing with the cover lock.
Annual Testing: The sensor should be tested at least once per year.
8. Support and Contact Information
For additional information, product warranty, or support, please refer to the Honeywell website or contact an authorized representative.
Honeywell Security Group Websites:
- General information: www.honeywell.com/security/emea/hscdownload
- Detailed installation guide: Available on the Honeywell website. Please consider before printing.
Contact Information:
- Honeywell Security Group (France):
BP1219, 1198 avenue du docteur Maurice Donat, Sophia Antipolis, 06254 Mougins Cedex.
Tel: +33.4.92.94.29.50
Fax: +33.4.92.94.29.60 - Honeywell Security Group (UK):
Newhouse Industrial Estate, Motherwell, Lanarkshire ML1 5SB, United Kingdom.
Tel: +44(0)1698 738200
Email: UK64Sales@Honeywell.com
Warranty Information:
Contact a local authorized Honeywell representative for product warranty information.
