L Shaped Computer Desk Instruction Manual
Note: A more detailed installation video is available on the product detail page on Amazon.
Product Overview and Options
This document provides instructions for assembling the ALLSTAND L Shaped Computer Desk. The desk can be assembled in four different configurations (Option 1, Option 2, Option 3, Option 4) to suit various space and usage needs.
Available Configurations:
- Option 1: Standard L-shape with shelving on one side.
- Option 2: L-shape with a smaller return on one side.
- Option 3: Extended L-shape with shelving on both ends.
- Option 4: L-shape with shelving on one side and a wider return on the other.
Contact Information:
E-mail: support@allstand.net
Made in China
♻️
Subdivision Diagram
The following diagram illustrates the main components of the desk, including desk surfaces, frame pieces, shelving units, and hardware.
Important Instructions Before Assembly
- Some parts of the computer desk have sharp edges, so please be attentive to avoid scratches when installing.
- Due to the small size of the hardware, please put them in a safe position when installing them to avoid accidental injury.
- In order to avoid a bad installation experience, please follow the steps in the instruction manual and carefully distinguish screws and steel strips. Having a helper will make the installation easier.
- ALLSTAND offers customers a free lifetime warranty. For product issues, after-sales service, or other relevant problems, please contact ALLSTAND via the email provided on the cover.
Assembly Parts List
| No. | Part Description | Quantity |
|---|---|---|
| 1 | Frame Piece | 2 PC |
| 2 | Frame Piece | 2 PC |
| 3 | Connecting Bar | 1 PCS |
| 4 | Shelf Frame | 1 PC |
| 5 | Desk Surface | 1 PC |
| 6 | Frame Piece | 1 PC |
| 7 | Frame Piece | 1 PC |
| 8 | Frame Piece | 1 PC |
| 9 | Frame Piece | 1 PC |
| 10 | Frame Piece | 1 PC |
| 11 | Support Bar | 2 PC |
| 12 | Shelf Unit Frame | 1 PC |
| 13 | Desk Surface/Extension | 2 PC |
| 14 | Shelf Frame | 2 PC |
| 15 | Shelf Frame | 4 PCS |
| 16 | Desk Surface (with power strip hole) | 1 PCS |
| 17 | Desk Surface | 1 PC |
| 18 | Upper Shelf Unit | 2 PC |
| 19 | Foot/Base Piece | 2 PCS |
| 20 | Light Strip | 1 PC |
| 21 | Recessed Power Strip | 1 PC |
| 22 | Monitor Stand Base | 1 PC |
| 23 | Monitor Stand Arm | 2 PCS |
| A | Screw | 23+2 PCS |
| B | Screw | 4 PCS |
| C | Screw | 26+2 PCS |
| D | Screw | 8+1 PCS |
| E | Screw | 12+1 PCS |
| F | Wrench | 1 PC |
| G | Screw | 2 PCS |
| H | Screw | 6 SETS |
| I | Screw | 2 PCS |
| J | Screw | 2 PCS |
| K | Screw | 2 PCS |
| L | Screw | 1 PCS |
Assembly Steps
Step 1: Assembly steps of the light strip
Required Parts: 4 or 5 (x1), 20 (x1), H (x6), L (x1)
Instructions:
Please remove the adhesive from the light strip before using it. (Only 1 strip)
There are two positions for attaching the light strip:
- On the bottom of shelf 4.
- On the bottom of shelf 5.
The diagram shows the light strip (part 20) being attached to the underside of either shelf 4 or shelf 5. Hardware H is used to secure the strip, with hardware L potentially used for final attachment or management of the cable.
Step 2: Assembly steps of the recessed power strip
Required Parts: 16 (x1), 21 (x1), I (x2), L (x1)
Instructions:
Attach part 21 (recessed power strip) to the corresponding holes of part 16 (desk surface) by using hardware I with hardware L.
The diagram illustrates part 21 being fitted into a cutout on part 16, secured by hardware I and L.
Step 3: Assembly steps of the monitor stand
Required Parts: 22 (x1), 23 (x2), A (x4), J (x2), K (x2), F (x1)
Instructions:
Attach part 23 (monitor stand arm) to part 22 (monitor stand base) using hardware A. Then, attach hardware K to the corresponding holes of part 23 using hardware J with hardware F. Do not fully tighten J.
The diagram shows the monitor stand components being assembled. Part 23 is attached to 22 with A. A close-up view shows hardware K being attached to 23 using J and F, with a note indicating that J should not be fully tightened.
Step 4: Assembly steps of the computer desk frame
Required Parts: 1 (x2), 3 (x1), C (x2), F (x1)
Instructions:
Use hardware C to connect part 1 (frame piece) and part 3 (connecting bar) with hardware F. Do not fully tighten screws until the end of step 19.
The diagram shows two frame pieces (part 1) being connected by a horizontal connecting bar (part 3) using screws C and wrench F.
Step 5: Attaching desk surface components
Required Parts: 2 (x2), 5 (x1), A (x3), E (x4), F (x1)
Instructions:
Building on Step 4, use hardware A to connect part 5 (desk surface) through the corresponding holes. Finally, use hardware E to connect part 2 (frame piece) and part 5. Do not fully tighten screws until the end of step 19.
The diagram shows part 5 being attached to the structure, followed by part 2 being attached to part 5 using hardware A and E.
Step 6: Attaching side panels
Required Parts: 2 (x2), 4 (x1), E (x8), F (x1)
Instructions:
Install hardware E to parts 2 and 4 using hardware F. Do not fully tighten screws until the end of step 19.
The diagram shows parts 2 and 4 being attached to the main desk frame using hardware E and F.
Step 7: Attaching the recessed power strip assembly
Required Parts: 16 (x1), C (x4), F (x1)
Instructions:
Use hardware C to connect part 16 (desk surface with power strip) to the structure from Step 6 using hardware F. Fully tighten hardware C screws using wrench F.
The diagram shows part 16 being attached to the desk structure, with hardware C and wrench F.
Step 8: Assembling the main desk frame
Required Parts: 6 (x1), 7 (x1), 8 (x1), 9 (x1), 10 (x1), 11 (x2), C (x6), D (x4), F (x1), L (x1)
Instructions:
Use hardware C to connect parts 6, 7, 8, 9, and 10. Ensure threading faces outwards. Then, attach part 11 (support bar) to the corresponding holes using hardware D. Tip: There are two adjacent threaded holes; choose to insert the one above. Do not fully tighten screws until the end of step 19.
The diagram shows the main frame components (6, 7, 8, 9, 10) being connected with hardware C. Part 11 is then attached using hardware D, with a tip about hole selection.
Step 9: Assembling the shelving units
Required Parts: 14 (x2), 15 (x4), C (x8), F (x1)
Instructions:
Connect parts 14 (shelf frames) to parts 15 (shelf frames) from the left and right sides using hardware C. Ensure threading faces outwards. Tip: There are two adjacent threaded holes; choose to insert the one below. Do not fully tighten screws until the end of step 19.
The diagram shows the shelving unit frames (parts 14 and 15) being assembled using hardware C.
Step 10: Attaching the upper shelf structure
Required Parts: 18 (x2), A (x4), F (x1)
Instructions:
Please decide the upper shelf height of the 18 parts (upper shelf units) at this time. Attach part 18 to the corresponding holes of the structure from Step 9 using hardware A. Do not fully tighten screws until the end of step 19.
The diagram shows the upper shelf units (part 18) being attached to the assembled shelving structure using hardware A.
STOP! SEE BELOW BEFORE PROCEEDING
Choose your desired configuration and follow the corresponding steps:
- Option 1: Please continue to Step 11, 12 & 19.
- Option 2: Please continue to Step 13, 14 & 19.
- Option 3: Please continue to Step 15, 16 & 19.
- Option 4: Please continue to Step 17, 18 & 19.
Diagrams illustrate the four distinct assembly options for the desk.
Option 1 Assembly
Step 11: Option 1 assembly
Required Parts: 12 (x1), 13 (x2), C (x6), F (x1)
Instructions:
According to the diagram, connect two parts of 13 (desk surface/extension) from the left and right sides using hardware C. Do not fully tighten screws until the end of step 19.
The diagram shows parts 12 (shelf unit frame) and 13 being connected to form the L-shape for Option 1.
Step 12: Option 1 assembly
Required Parts: A (x12), B (x4), F (x1)
Instructions:
Attach the upper part (assembled in Step 10) to the corresponding holes of the structure from Step 11 by using hardware A and B. Do not fully tighten screws until the end of step 19.
The diagram shows the upper shelf assembly being attached to the main desk structure for Option 1 using hardware A and B.
Option 2 Assembly
Step 13: Option 2 assembly
Required Parts: 12 (x1), 13 (x2), C (x6), F (x1)
Instructions:
According to the diagram, connect two parts of 13 (desk surface/extension) from the left and right sides using hardware C. Do not fully tighten screws until the end of step 19.
The diagram shows parts 12 (shelf unit frame) and 13 being connected to form the L-shape for Option 2.
Step 14: Option 2 assembly
Required Parts: A (x12), B (x4), F (x1)
Instructions:
Attach the upper part (assembled in Step 10) to the corresponding holes of the structure from Step 13 by using hardware A and B. Do not fully tighten screws until the end of step 19.
The diagram shows the upper shelf assembly being attached to the main desk structure for Option 2 using hardware A and B.
Option 3 Assembly
Step 15: Option 3 assembly
Required Parts: 12 (x1), 13 (x2), C (x6), F (x1)
Instructions:
According to the diagram, connect two parts of 13 (desk surface/extension) from the left and right sides using hardware C. Do not fully tighten screws until the end of step 19.
The diagram shows parts 12 (shelf unit frame) and 13 being connected to form the L-shape for Option 3.
Step 16: Option 3 assembly
Required Parts: A (x12), B (x4), F (x1)
Instructions:
Attach the upper part (assembled in Step 10) to the corresponding holes of the structure from Step 15 by using hardware A and B. Do not fully tighten screws until the end of step 19.
The diagram shows the upper shelf assembly being attached to the main desk structure for Option 3 using hardware A and B.
Option 4 Assembly
Step 17: Option 4 assembly
Required Parts: 12 (x1), 13 (x2), C (x6), F (x1)
Instructions:
According to the diagram, connect two parts of 13 (desk surface/extension) from the left and right sides using hardware C. Do not fully tighten screws until the end of step 19.
The diagram shows parts 12 (shelf unit frame) and 13 being connected to form the L-shape for Option 4.
Step 18: Option 4 assembly
Required Parts: A (x12), B (x4), F (x1)
Instructions:
Attach the upper part (assembled in Step 10) to the corresponding holes of the structure from Step 17 by using hardware A and B. Do not fully tighten screws until the end of step 19.
The diagram shows the upper shelf assembly being attached to the main desk structure for Option 4 using hardware A and B.
Step 19: Final Assembly (All Options)
Required Parts: 19 (x2), D (x4), G (x2), L (x1), J (x1 - implied from diagram)
Instructions:
Fully tighten all screws at the end of this step. Use hardware D to connect part 19 (foot/base piece) to each side of the table. Then, attach the monitor stand (assembled in Step 3) to the corresponding holes of the table by using hardware J.
The diagram shows the final tightening of screws and the attachment of base pieces (part 19) and the monitor stand assembly.
Installation completed.
Final Assembly Views
Option 1: A diagram shows the completed L-shaped desk with shelving on one side.
Option 2: A diagram shows the completed L-shaped desk with a smaller return on one side.
Option 3: A diagram shows the completed extended L-shaped desk with shelving on both ends.
Option 4: A diagram shows the completed L-shaped desk with shelving on one side and a wider return on the other.
