Lift Top Coffee Table Instruction Manual

ASSEMBLY INSTRUCTION

Decomposition of Components

An exploded view diagram shows all components of the lift top coffee table, labeled with numbers 1 through 18, and hardware components labeled A through N. The diagram illustrates how the various parts fit together.

Parts List

• 1: Top Panel (x1)
• 2: Bottom Panel (x1)
• 3: Middle Shelf (x1)
• 4: Side Panel (x1)
• 5: Side Panel (x1)
• 6: Base Panel (x1)
• 7: Side Frame (x2)
• 8: Back Panel (x2)
• 9: Divider Panel (x2)
• 10: Support Panel (x1)
• 11: Lift Top Panel (x1)
• 12: Base Support Rail (x2)
• 13: Base Support Rail (x2)
• 14: Foot (x4)
• 15: Sliding Mechanism Part 1 (x1)
• 16: Sliding Mechanism Part 2 (x1)
• 17: Sliding Mechanism Part 3 (x1)
• 18: Support Bar (x1)

Hardware List

• A: Cam Lock (x36+3)
• B: Cam Bolt (x36+3)
• C: Screw Ø6*30mm (x44+3)
• D: Screw Ø5*38mm (x16+1)
• E: Screw 3/4"*12mm (x26+2)
• F: Screw 3.5*12mm (x4)
• G: Screw 1/4"*28mm (x6)
• H: Screw Ø6*17 (x4)
• I: Bracket (x2)
• J: Sleeve (x4)
• K: Sliding Rail Mount (x4)
• L: Lift Mechanism Part 1 (x1)
• M: Lift Mechanism Part 2 (x1)
• N: Wood Dowel (x2)

Important Instructions

• We offer customers a free lifetime warranty. If you need help regarding product issues, after-sales service, or other relevant problems, please contact us via the email provided on the cover.
• If using power drills for assembly, please be sure to adjust the appropriate speed and accessories. Excessive rotational speed or unsuitable drill bits may cause damage to screws and boards. ⚠️
• Some parts of the Coffee Table have sharp edges, so please be attentive to avoid scratches when installing. ❗
• Due to the small size of the hardware, please put them in a safe position when installing them to avoid accidental loss.
• In order to avoid a bad installation experience, please follow the steps in the instruction manual carefully and distinguish screws and steel strips. Having a helper will make the installation certainly easier.

STEP 1

Two Cam Bolts (B) are screwed into the pre-drilled holes on the underside of the Top Panel (1). The arrow on the Cam Bolt should point towards the edge hole. This is repeated for all indicated positions. The Base Panel (6) is then placed with its 'FRONT' indicator facing forward. The holes on the Base Panel (6) are aligned with the Cam Bolts (B) on the Top Panel (1). Cam Locks (A) are inserted into the large holes on the Base Panel (6), with their arrows pointing towards the incoming Cam Bolts. The Cam Locks are tightened clockwise ? using a screwdriver to secure the panels.

Note: Please place the board 6 strictly according to the direction of the arrows. ⬆️

Hardware used: Cam Bolts (B) x4, Cam Locks (A) x4.

STEP 2

Two Side Panels (4 and 5) are attached to the Base Panel (6). Cam Bolts (B) are inserted into the Side Panels (4 and 5). Cam Locks (A) are inserted into the Base Panel (6) and tightened to secure the Side Panels. Screws (C) and (D) are used to further reinforce the structure, along with Cam Bolts (B) and Cam Locks (A) connecting the Side Panels to the Base Panel. The 'FRONT' indicator on the Side Panels should face forward.

Note: Please strictly install boards 4 and 5 as shown in step 2.

Hardware used: Cam Bolts (B) x4, Cam Locks (A) x4, Screws (C) x4, Screws (D) x4.

STEP 3

Two long Support Bars (2 and 3) are prepared. Cam Bolts (B) are screwed into the pre-drilled holes on these bars. This is repeated for all indicated positions.

Hardware used: Cam Bolts (B) x10.

STEP 4

The Top Panel (1) is positioned above the assembled structure. The two Support Bars (2 and 3) are placed between the Side Panels (4 and 5). Cam Bolts (B) are inserted into the ends of the Support Bars (2 and 3). Cam Locks (A) are inserted into the Side Panels (4 and 5) and tightened clockwise ? to secure the Support Bars. Screws (C) are also used to attach the Support Bars to the Side Panels. The 'FRONT' indicator on the Side Panels should face forward.

Note: The front icon (on the side panels) should be facing up. ⬆️

Note: Icon front top is board 3, bottom is board 2.

Hardware used: Cam Bolts (B) x10, Cam Locks (A) x8, Screws (C) x10.

STEP 5

Two Side Frames (7) are prepared. Cam Bolts (B) are screwed into the pre-drilled holes on these frames. This is repeated for all indicated positions.

Hardware used: Cam Bolts (B) x4.

STEP 6

The assembled frame structure (from previous steps) is shown. The two Side Frames (7) are attached to the main body. Cam Bolts (B) are inserted into the Side Frames (7). Cam Locks (A) are inserted into the main body panels (2, 3, 4, 5) and tightened clockwise ? to secure the Side Frames. Screws (C) are also used to attach the Side Frames to the main body.

Note: Be careful when rotating for the next step.

Hardware used: Cam Bolts (B) x4, Cam Locks (A) x4, Screws (C) x4.

STEP 7

Two Divider Panels (9) are inserted between the Side Frames (7) and into the main body. Cam Bolts (A) are inserted into the Divider Panels (9). Cam Locks (C) are inserted into the Side Frames (7) and main body panels (3, 5) and tightened clockwise ?. Screws (C) are also used to secure the Divider Panels. The diagram shows specific orientations for holes: "Hole facing Left" and "Hole facing Right".

Hardware used: Cam Bolts (A) x4, Cam Locks (C) x4, Screws (C) x4.

STEP 8

Two Back Panels (8) are inserted into the grooves of the Side Frames (7) and the main body. The diagram indicates "4 hole facing upwards". Screws (C) are used to secure the Back Panels.

Hardware used: Screws (C) x4.

STEP 9

The Lift Top Panel (11) is prepared. Cam Bolts (B) are screwed into the underside of the Lift Top Panel (11). Wood Dowels (N) are inserted into specific holes. Screws (F) are used to attach brackets (I) and sliding mechanism parts (N) to the Lift Top Panel (11). The panel is then rotated 180 degrees.

Hardware used: Cam Bolts (B) x10, Screws (F) x4, Wood Dowels (N) x2, Brackets (I) x2.

STEP 10

The Lift Top Panel (11) is placed onto the main body. Cam Locks (C) are inserted into the main body panels (7, 8, 9) and tightened clockwise ? to secure the Lift Top Panel (11).

Hardware used: Cam Locks (C) x12.

STEP 11

Screws (D) are used to attach the Support Panel (11) to the main body structure (panels 3 and 8). The diagram shows multiple screws being inserted into pre-drilled holes.

Hardware used: Screws (D) x12.

STEP 12

The Base Support Rails (12 and 13) are attached to the Bottom Panel (2). Cam Bolts (A) are inserted into the Base Support Rails (12 and 13). Cam Locks (B) are inserted into the Bottom Panel (2) and tightened clockwise ?. Feet (14) are screwed into the Base Support Rails (12 and 13).

Hardware used: Cam Bolts (A) x8, Cam Locks (B) x8, Feet (14) x4.

STEP 13

The assembled base structure is attached to the main body. Cam Locks (C) are inserted into the main body panels (11, 12, 13) and tightened clockwise ? to secure the base.

Hardware used: Cam Locks (C) x8.

STEP 14

The top surface of the main body is shown. Cam Bolts (A) are inserted into the top edges of the Side Panels (4, 5) and Side Frames (7). Cam Locks (A) are inserted into the underside of the Top Panel (1) and tightened clockwise ?. This secures the main body to the top.

Hardware used: Cam Bolts (A) x10, Cam Locks (A) x10.

STEP 15

Sliding mechanism parts (15) are attached to the main body. Screws (G) are used to attach the sliding mechanism parts (15) to the main body panels (3). Sleeves (J) are inserted into the sliding mechanism parts (15).

Note: Note the direction of the arrow. ➡️

Hardware used: Screws (G) x4, Sleeves (J) x4.

STEP 16

Sliding mechanism parts (16) are attached to the Divider Panels (9). Screws (H) are used to attach the sliding mechanism parts (16) to the Divider Panels (9). The Back Panels (10) are then slid into place.

Hardware used: Screws (H) x4.

STEP 17

The sliding barn doors (17) are attached to the main body. Sliding Rail Mounts (K) are attached to the barn doors (17) using screws (E). The barn doors are then hung onto the sliding mechanism parts (15) attached to the main body. Brackets (I) are attached to the top of the barn doors using screws (E).

Hardware used: Sliding Rail Mounts (K) x4, Screws (E) x8, Brackets (I) x2.

STEP 18

The lift mechanism is attached to the Top Panel (11) and the main body. Cam Bolts (E) are inserted into the main body panels (4, 5). Cam Locks (M) are inserted into the Lift Mechanism (M) and tightened. The Lift Mechanism (L) is attached to the Top Panel (11) using screws (E). The entire assembly is rotated 180 degrees.

Note: Note the direction of the arrow. ➡️

Hardware used: Screws (E) x6, Lift Mechanism (M) x1, Cam Bolts (E) x8, Lift Mechanism (L) x1.

STEP 19

The lift mechanism is connected to the Top Panel (11). Screws (E) are used to attach the lift mechanism to the Top Panel (11). Screws (G) are used to attach the lift mechanism to the main body. Cam Locks (E) are inserted into the main body and tightened.

Hardware used: Screws (E) x12, Screws (G) x2.

STEP 20

The final assembly is shown. The lift top mechanism is fully connected and functional. The diagram shows the completed coffee table.

Hardware used: Screws (O) x4. (Note: Hardware 'O' was not listed in the initial parts list.)