Smart Reader EP20CKQ
Quick Start Guide Version 1.0
Visit Armatura at: www.armatura.us
Product Overview
Key Features
The EP20CKQ reader is a compact, multi-frequency RFID reader supporting over 100 RFID card types, NFC, and Bluetooth Low Energy credentials. It is designed to fit single-gang, European-standard, and Asian-standard boxes.
Device Components
Front View: Features a 1 LED Indicator, 2 Touch Button, 3 Card Reading Area, 4 QR Code Scanner, 5 Mounting Hole, and 6 Tamper Switch.
Back View: Shows mounting points and the tamper switch.
Side View: Dimensions approximately 89.8mm (3.54 inches) in length and 21.9mm (0.86 inches) in width.
Bottom View: Dimensions approximately 107.8mm (4.24 inches) in length and 89.8mm (3.54 inches) in width.
Parts Included
Ensure your package contains the following items. Contact your dealer if any are missing.
- Armatura EP20CKQ Reader (1pc)
- Quick Start Guide and Mounting Template (1pc)
- Mounting Plate (1pc)
- Screwdriver (1pc)
- Self-tapping screws (4pcs) and Anchors (4pcs) for wall mounting
- Torx screw (1pc) for fixing the reader to the mounting plate
Recommended Parts (Not Supplied)
- Cable: 5-10 conductor for Wiegand, or 4-conductor twisted pair, shielded, UL approved (e.g., Belden 3107A) for OSDP.
- Certified LPS DC power supply.
- Metal or plastic junction box.
- Drill with various bits for mounting hardware.
- Mounting hardware.
Reader Connection
The EP20CKQ series can communicate with the control panel via either RS-485 (OSDP) or Wiegand.
1. Connection via Wiegand
Pigtail Connections:
| Pigtail | Description |
|---|---|
| Red | +9~24V DC |
| Black | Ground |
| Red/Green | RS-485 A |
| Brown | RS-485 B |
| Bare | Wiegand Data 0 |
| Green | Wiegand Data1 |
| White | Green LED Input |
| Orange | Red LED Input |
| Pink | Beep Input |
| Yellow | Tamper |
| Violet | Tamper |
Pinout Diagram Description (Wiegand): The reader has labeled pins for TAMPER, BEEP, RLED (Red LED), GLED (Green LED), WD1 (Wiegand Data 1), WDO (Wiegand Data 0), GND (Ground), and +12V (Power Input).
2. Connection via RS-485 (OSDP)
RS-485 Port Connections:
The reader connects to the control panel using +9~24V DC, GND, RS-485 B, and RS-485 A.
Install The Reader On The Wall
Follow these steps for wall installation:
- Attach the mounting template sticker to the wall, approximately 59 inches (1.5m) from the ground (adjustable). Drill holes according to the template.
- Secure the mounting plate onto the wall using the provided wall mounting screws.
- Pass the wires through the wiring hole and connect them. Then, attach the reader to the mounting plate from top to bottom.
- Fasten the reader to the mounting plate with the security Torx screw.
Note: The installation method for the EP20C series is similar. The EP20CKQ is used as an example and will not be repeated.
Using And Testing The Reader
Power On: When the reader is powered on, it will beep and the LEDs will flash.
Card Presentation: Present a card face-on to the reader until you hear a "beep". The reader is now working correctly.
Keypad: Used for PIN entry.
Scan QR Code: Area for scanning QR codes.
Card: The primary area for card reading.
Swipe Card: Indicates the action of swiping a card (though the reader is likely tap-to-read).
Frequency Bands And Maximum Output Power (For EU)
| Frequency bands | Maximum output power |
|---|---|
| 2402MHz-2480MHz | 6.35dBm |
| 125kHz | -6.55dBuA/m@10m |
| 13.56MHz | -1.15dBuA/m@10m |
Certificate Information
The product carries certifications including UK CA, CE, FC, and ROHS.
FCC + CE Compliance
Armatura LLC declares this product complies with the essential requirements and other provisions of Directive 2014/53/EU.
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
If this equipment causes harmful interference to radio or television reception, try one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Supplier's Declaration of Conformity
Unique Identifier: Smart Reader
Model No.: EP20CKQ
Responsible Party – U.S. Contact Information:
US Company Name: Armatura LLC
Address: 190 Bluegrass Valley Parkway Alpharetta, GA 3005, USA
Internet contact information: www.armatura.us
