Parts and Fitting Packaging Detail
This section details the components included in the packaging for assembly.
Box #1
- A. HEADBOARD PANEL - 1 PC
- B. HEADBOARD LEG - LEFT - 1 PC
- C. HEADBOARD LEG - RIGHT - 1 PC
- D. FOOTBOARD - 1 PC
- HARDWARE BOX
Box #2
- E. LEFT SIDERAIL - 1 PC
- F. RIGHT SIDERAIL - 1 PC
- G. CENTER SLAT - 1 PC
- H. CENTER LEG - 4 PCS
- HARDWARE BOX
Box #3
- I. BED SLATS - 12 PCS
A visual representation shows the assembled platform bed, indicating the general placement of these parts.
Hardware Packed in Box #2
| Item | Description | Quantity |
|---|---|---|
| 1 | PHILLIPS HEAD BOLT 20MM | 8 PCS |
| 2 | WASHER 8MM | 8 PCS |
| 3 | METAL PIN 40MM | 2 PCS |
| 4 | WOOD SCREW Ø8X30MM | 8 PCS |
| 5 | ALLEN BOLT 40MM | 10 PCS |
| 6 | ALLEN KEY | 1 PC |
Hardware Packed in Box #1
| Item | Description | Quantity |
|---|---|---|
| 1 | ALLEN BOLT 35MM | 2 PCS |
| 2 | ALLEN BOLT 55MM | 2 PCS |
| 3 | ALLEN BOLT 70MM | 4 PCS |
| 4 | ALLEN KEY | 1 PC |
Note: Your box may contain extra hardware.
Tool Required
A Phillips Head Screw Driver (not provided) is required for assembly.
Assembly Instructions
Step 1: Attach Headboard Legs
Follow the illustration: Insert the Allen Bolt [1] (from hardware pack #1) into the pre-drilled hole to connect the Headboard Leg [B/C] to the Headboard Panel [A]. Ensure the legs are oriented correctly (Left [B] and Right [C]).
Important: For this step, use hardware packed in Box #1.
Step 2: Attach Left Siderail
Fix the Left Siderail [E] to the Headboard Assembly [A/B/C] using Phillips Head Bolts [1] and Washers [2] (from hardware pack #2). Do not tighten bolts completely until the assembly is finished.
Step 3: Attach Footboard to Left Siderail
Align Metal Pin [3] into the pre-drilled hole on the other end of the Left Siderail [E] and the Footboard [D]. Then, fix the other end of the Left Siderail [E] to the Footboard [D] using Phillips Head Bolts [1] and Washers [2] (from hardware pack #2).
Step 4: Attach Right Siderail
Repeat the same process as Step 2 and Step 3 to fix the Right Siderail [F] to the Headboard Assembly [A/B/C] and the Footboard [D].
Step 5: Install Center Slat and Legs
Arrange the Center Slat [G] so that the T-Nut is facing the floor. Slide Allen Bolts [5] from the top of the Center Slat [G] into the 2nd, 4th, 7th, and 9th pre-drilled holes. Fix the Center Legs [H] to the Center Slat [G] using Allen Bolts [5] and the Allen Key [6].
Step 6: Attach Bed Slats
Spread the Bed Slats [I] across the bed frame. Fix the 1st, 6th, 7th, and 12th Bed Slats [I] to the bed frame using Wood Screws [4]. Use the pilot holes on the Siderails [E/F] as a reference for correct placement.
Step 7: Secure Bed Slats to Center Slat
Slide the Center Slat [G] under the Bed Slats [I]. Slide Allen Bolts [5] from the top of the Bed Slats [I] through the pre-drilled holes on the 1st, 2nd, 5th, 8th, 11th, and 12th Bed Slats [I]. Tighten these Allen Bolts [5] with the Allen Key [6] to secure the Bed Slats [I] to the Center Slat [G].
Instructions for Adjusting Levelers
To adjust the levelers:
- Position the bed in your room.
- Locate the levelers under each center leg.
- Turn counter-clockwise ↩️ to extend, or clockwise ↪️ to contract.
- Adjust the levelers until each leg is applying equal upward pressure on the center slat.
Maintenance Instructions
- Remove box spring and mattress before moving your bed.
- Lift your bed when moving it. Dragging can damage the center support.
- Readjust levelers after moving your bed.
Document updated: June 11th, 2015
