Yaheetech Drafting Table Assembly Instructions
Model # 611097
Dear Customers,
Thank you for purchasing our product. Please read this instruction manual carefully after receiving this product. It will help you assemble this product quickly, safely and correctly. You can keep this manual for future reference.
IMPORTANT
Please follow the instruction manuals and use a pad to protect the product during your assembly.
For easier and better assembly, 2 or more adults are required.
The expected assembly time for this product is 2 hours, depending on the individual's manipulative ability.
Safety Precautions:
- This product is not intended for children to climb. Please keep your children from climbing this product.
- Do not place the product near the fire or heat sources! Caution Fire Hazard!
- Do not use corrosive cleaners for cleaning!
- Be careful of your hands when setting up! We recommend wearing protective gloves for assembly.
- Please check the number and condition of the parts according to the parts list. If any parts are damaged or missing, please contact us immediately.
- We recommend checking the tightness of all connections between parts every six months.
- The warnings, cautions, and instructions listed in this manual may not cover all possible situations that may arise when using the product. Please contact Yaheetech via e-mail info@yahee.com.cn if you need further information or help.
Parts List
The following parts are included in your package:
- Part 1: Tabletop (x1)
- Part 2: Adjustable Feet (x6)
- Part 3: Left Frame (x1)
- Part 4: Center Frame (x1)
- Part 5: Support Bar (x1)
- Part 6: Back Panel (x1)
- Part 7: Shelf (x1)
- Part 8: Long Support Bar (x1)
- Part 9: Adjuster Bracket L (x1)
- Part 9: Adjuster Bracket R (x1)
- Part 10: Small Tube (x2)
- Part 11: Mounting Plate (x2)
- Part 12: Stool Seat (x1)
- Part 13: Stool Ring (x1)
- Part 14: Stool Leg Frame Left (x1)
- Part 15: Stool Leg Frame Right (x1)
- Part 16: Top Surface (x1)
- Part 17: Right Frame (x1)
- Part 18: Drawer Support Frame (x1)
- Part 19: Drawer Support Frame (x1)
- Part 20: Short Tube (x2)
- Part 21: Short Tube (x2)
- Part 22: Drawer Box (x3)
- Part 23: M6x60mm Bolt (x4)
- Part 24: M6x35mm Bolt (x4)
- Part 25: M6x35mm Bolt (x4)
- Part 26: Screws (quantity not specified in diagram)
- Part 27: M6x25mm Bolt (quantity not specified in diagram)
- Part 28: M6x20mm Bolt (quantity not specified in diagram)
- Part 29: Nuts (x2)
- Part 30: Screws (x16)
- Part 31: M6x35mm Bolt (x2)
- Part 32: M6x35mm Bolt (x4)
To install successfully, please do not fully tighten any screw (unless there are special requirements) until all screws are screwed in.
Attention: It will be faster and more convenient to assemble the drafting table by 2 or more people.
Assembly Steps
Step 1: Assemble the Base Frame
Attach the adjustable feet (2) to the bottom of the left frame (3) and the right frame (17). Connect the left frame (3), right frame (17), and center frame (4) using the support bar (5) and M6x60mm bolts (23). Ensure the side with holes on the center frame faces inward. Turn the side with holes inward.
Step 2: Attach the Shelf and Back Panel
Attach the shelf (7) to the lower part of the frame assembly using screws (26). Attach the back panel (6) to the upper part of the frame assembly using screws (26).
Step 3: Assemble the Drawer Unit Supports
Attach the drawer support frames (18 and 19) to the main frame using short tubes (20 and 21), M6x25mm bolts (27), and M6x20mm bolts (28). Ensure the correct orientation as shown in the diagrams.
Step 4: Attach the Top Surface
Place the top surface (16) onto the assembled frame. Secure it using M6x35mm bolts (28) and mounting plates (11). Note the direction of teeth in Bracket (9).
Step 5: Install the Adjuster Brackets
Attach the adjuster brackets (9) to the underside of the tabletop (1). Use screws (30) for this step. Pay attention to the orientation of the teeth on the brackets. If the adjuster bracket does not match the hole position, restore it to its initial state by pulling it to the maximum and then back to the minimum.
Step 6: Attach the Main Tabletop
Attach the main tabletop (1) to the frame using M6x35mm bolts (31) and M6x60mm bolts (23). Ensure the side with holes faces inward.
Step 7: Connect the Drawer Unit
Connect the drawer unit support frames (18 and 19) to the main frame using short tubes (20 and 21), M6x25mm bolts (27), and M6x20mm bolts (28). Attach the drawer unit to the main frame using M6x35mm bolts (31) and M6x60mm bolts (23).
Step 8: Secure the Top Surface
Attach the top surface (16) to the frame using M6x35mm bolts (28). Ensure the square and rounded edges are correctly positioned.
Step 9: Install the Drawer Boxes
Insert the drawer boxes (22) into the assembled drawer unit. Ensure they slide in smoothly.
Step 10: Final Tightening
Fully tighten all bolts from Step 1-9, except for Screws (30) which should remain slightly loose for now.
Step 11: Attach the Stool Seat
Assemble the stool by attaching the stool seat (12) to the stool leg frames (14 and 15) using M6x35mm bolts (25) and stool ring (13). Use M6x35mm bolts (32) to secure the stool legs to the seat.
Step 12: Final Tightening of Adjuster Brackets
Fully tighten all 16 screws (30) for the adjuster brackets.
Product Information
Thank you for purchasing a Yaheetech product!
At Yaheetech, we are dedicated to bringing you the best online shopping experience and making your life comfortable. We pride ourselves on an integrated supply chain team that works meticulously to deliver you products and service with greatest value. Our networks span across the US, the United Kingdom, Germany, France and six more European countries. It is always our belief that how customers view our business and service ultimately defines our brand.
So, how did we do? Please let us know by making an online remark about it.
- Good job. Would you like to share your experience to assist others with their shopping decisions?
- Not good. Can you give us a chance to fix the problem?
For further assistance or to download a user manual, please visit our website or contact us at info@yahee.com.cn.
