Jenn-Air Electric Combo Microwave/Wall Oven Dimension Guide
Product Models: JOECC530RL, JOECC530RM, JOECC730RL, JOECC730RM
Appliance Dimensions
The following tables provide detailed dimensions for Jenn-Air electric combo microwave/wall ovens.
| Appliance | 30" Electric Combo Microwave/Wall Oven | 30" Electric Combo Microwave/Wall Oven | ||
|---|---|---|---|---|
| Units | in | cm | in | cm |
| A. Depth Closed Excluding Handle (Flush Install) | 247⁄16 | 62 | 247⁄16 | 62 |
| B. Depth Closed Including Handle | 275⁄16 | 69.3 | 261⁄2 | 67.3 |
| C. Depth to Back of Console (Standard Install) | 231⁄16 | 58.6 | 231⁄16 | 58.6 |
| D. Depth with Door Open 90° | 463⁄16 | 117.3 | 461⁄8 | 117.1 |
| E. Maximum Height (Including Console) | 443⁄4 | 113.6 | 443⁄4 | 113.5 |
| E. Minimum Height (Including Console) | 4215⁄16 | 109.1 | 427⁄8 | 109 |
| F. Face Width | 293⁄4 | 75.6 | 293⁄4 | 75.8 |
| G. Maximum Height (Not Including Console) | 43 | 109.2 | 43 | 109.2 |
| G. Minimum Height (Not Including Console) | 411⁄8 | 104.4 | 411⁄8 | 104.4 |
| H. Recessed Width | 285⁄16 | 71.9 | 285⁄16 | 71.9 |
Feet are available through Service to increase product height for installations where taller cutouts were used.
[Diagram showing angled view of the oven with dimensions labeled A through H]
[Diagram showing side view of the oven with dimensions labeled A through G]
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
- Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with oven.
- Recessed installation area must provide complete enclosure around the recessed portion of the oven.
- Grounded electrical supply is required. See "Electrical Requirements" section.
- Electrical supply junction box should be located 3" (7.6 cm) maximum above the top enclosure surface when the oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the right rear or left rear corner of the support surface to pass the appliance cable through to the junction box.
- Oven support surface must be solid, level, and flush with the bottom of the cabinet cutout. The floor must be able to support a total weight (microwave and built-in oven) of 350 lbs (158.7 kg) for 30" (76.2 cm) models.
IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).
For ovens installed using flush installation cabinetry, a deflector assembly must be installed. See "Install Deflector Assembly" section of the owner's manual for further instruction.
Cabinet Dimensions - Built-in Microwave/Oven Combination (Standard Installation)
30" (76.2 cm) models
- A. 30" (76.2 cm) minimum cabinet width
- B. 21⁄4" (5.7 cm) top of cutout to bottom of upper cabinet door
- C. 191⁄4" (48.9 cm) bottom of cutout to floor is recommended. 71⁄2"-191⁄4" (19.1 cm-48.9 cm) bottom of cutout to floor is acceptable.
- D. 281⁄2" (72.4 cm) minimum cutout width
- E. 11⁄2" (3.8 cm) minimum bottom of cutout to top of cabinet door
- F. 415⁄16" (105 cm)* recommended cutout height
- G. 24" (60.7 cm) cutout depth
*NOTE: The cutout height can be between 41" (104.5 cm) and 417⁄8" (106.3 cm) for microwave/oven combination.
[Diagram showing cabinet dimensions for built-in microwave/oven combination with labels A through G]
Flush Installation
A 25" (63.5 cm) minimum cutout depth is required.
These dimensions will result in a 1/4" (6 mm) reveal on the top, a 1/4" (6 mm) reveal on the sides, and a 1/8" (3 mm) reveal on the bottom of the wall oven.
The front face of the cleats and platform will be visible and should be treated as a finished surface.
[Diagram showing front view for flush installation with dimensions labeled A through J]
[Diagram showing side view for flush installation]
[Diagram showing top view for flush installation with dimensions labeled A through D]
30" (76.2 cm) models
- A. 2" (5.1 cm) spacer the entire depth of the cutout*
- B. 25" (63.5 cm) depth of cutout
- C. 11⁄2" (3.8 cm) recess from front of cabinet
- D. 7/8" (2.2 cm) side cleat*
*Cleats and spacers must be recessed 13⁄8" (3.5 cm) from the front of the cabinet.
30" (76.2 cm) models
- A. 3/4" (1.9 cm) top cleat*
- B. 301⁄4" (76.8 cm) minimum width of flush inset cutout**
- C. 287⁄8" (73.3 cm) minimum width of opening
- D. 445⁄16" (112.5 cm) minimum height of flush inset cutout
- E. 439⁄16" (110.6 cm) recommended cutout height
- F. 11/16" (1.7 cm) side cleat*
- G. 15/16" to 11⁄16" (2.3 cm to 3.5 cm) recommended, 1/4" (0.6 cm) allowable with optional foot.***
- H. Recommended junction box location.
- I. 71⁄2"-191⁄4" (19 cm-48.9 cm) bottom of cutout to floor
- J. 25" (63.5 cm) minimum depth of cutout
*Cleats and spacers must be recessed 13⁄8" (3.5 cm) from the front of the cabinet.
**These dimensions will lead to side gaps of 1/4" (0.6 cm).
***Top and bottom gaps will be 3/8" (0.9 cm) gap above the 1/8" (0.3 cm) gap below the product. Top and bottom gaps not required for installation. Expose areas of the cabinet should be finished to match.
Feet are available through Service to increase product height for installations where taller cutouts were used.
NOTE: This is an alternate option to install your product in the cabinet and obtain a flush look. For standard installation, refer section "Product Dimensions - Built-in Microwave/Oven Combination, Standard Installation."
NOTE: For flush installations add the deflector assembly. See "Install Deflector Assembly” section of the owner's manual for further instruction.
Electrical Requirements
▲ WARNING
Electrical Shock Hazard
- Disconnect power before servicing.
- Electrically ground appliance.
- Failure to do so can result in death, fire, or electrical shock.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and the wire gauge are in accordance with local codes.
Check with a qualified electrical installer if you are not sure the oven is properly grounded.
This oven must be connected to a grounded metal, permanent wiring system.
Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances.
For obtaining copies of code standards, contact:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575.
Electrical Connection
To properly install your oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial/rating plate. The model/serial/rating plate is located under the control panel on single ovens and under the control panel on the upper oven cavity on double ovens. See the following illustration.
[Illustration showing the location of the model/serial/rating plate labeled A]
A. Model/serial/rating plate
Models rated from 7.3 to 9.6 kW at 240 V (5.4 to 7.4 kW at 208 V) require a separate 40 A circuit.
Models rated at 4.8 kW and below at 240 V (3.6 kW and below at 208 V) require a separate 20 A circuit.
A circuit breaker is recommended.
Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or nonmetallic sheathed, copper cable (with grounding wire). See the “Make Electrical Connection" section in the Owner's Manual.
Flexible conduit from the oven should be connected directly to the junction box.
Fuse both sides of the line.
Do not cut the conduit. The length of conduit provided is for serviceability of the oven.
A UL listed or CSA-approved conduit connector must be provided.
If the house has aluminum wiring, follow the procedure below:
- Connect the aluminum wiring using special connectors and/or tools designed and UL listed for joining copper to aluminum.
- Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry-accepted wiring practices.
- Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575.
