Installation Guide for JENN-AIR models including: JKS3000DNWW 27 Inch 4.3 cu. ft. Single Built In Oven, JKS3000DNWW, 27 Inch 4.3 cu. ft. Single Built In Oven, Single Built In Oven, Built In Oven, Oven
Dimension Guide (JJW2427LL dimension-guide )
Four encastré simple 27 pouce 4.3 cu. ft. Jenn-Air Canada - Vente! Meilleur prix et évaluations
INSTALLATION INSTRUCTIONS
REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Tools Needed
Phillips screwdriver Measuring tape Hand or electric drill (for wall cabinet installations) 1" (2.5 cm) drill bit (for wall cabinet installations) Level Flat-blade screwdriver
Parts Needed
UL listed or CSA-approved conduit connector UL listed wire connectors
Parts Supplied
#8-18 x 3/4" (1.9 cm) screws - single ovens (2), double ovens (4)
#8-18 x 3/8" (9.5 mm) screws - bottom vent (2) #8-18 x 3/8" (9.5 mm) screws - bottom vent shield (2) #8-18 x 3/8" (9.5 mm) screws - plastic feet (4) Rear feet - double oven (2) Front feet - double oven (2) Bottom vent shield Bottom vent trim
Check local codes. Check existing electrical supply. See the "Electrical Requirements" section.
It is recommended that all electrical connections be made by a licensed, qualified electrical installer. NOTE: Be sure to purchase only JennAir factory-certified parts and accessories for your appliance. Your installation may require additional parts. To order, refer to the contact information referenced in your Quick Start Guide.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) inches beyond the bottom of the cabinets.
Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with oven.
Recessed installation area must provide complete enclosure around the recessed portion of the oven.
Grounded electrical supply is required. See "Electrical Requirements" section.
Electrical supply junction box should be located 3" (7.6 cm) maximum below the support surface when the oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the right rear or left rear corner of the support surface to pass the appliance cable through to the junction box.
NOTE: For undercounter installation, it is recommended that the junction box be located in the adjacent right or left cabinet. If you are installing the junction box on rear wall behind oven, it is recommended that the junction box be recessed and located in the upper center of the cabinet.
Oven support surface must be solid, level and flush with bottom of cabinet cutout.
Floor must be able to support a single oven weight of 200 lbs (91 kg) for 30" (76.2 cm) models.
Floor must be able to support a double oven weight of 330 lbs (150 kg) for 30" (76.2 cm) models.
IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).
Product Dimensions - Single Ovens
H
G
F
A
E
B
D
C
27" (68.6 cm) models A. 303/16" (76.6 cm) maximum
overall height B. 27" (68.6 cm) overall width C. For Noir models - 263/8"
(67 cm) For Raise models - 273/16" (69 cm) D. 231/4" (59.1 cm) maximum recessed depth E. 26" (66 cm) recessed height F. 48" (121.9 cm) flexible conduit length G. 251/2" (64.7 cm) maximum recessed width H. 12" (30.5 cm) from back of control panel to start of strain relief
30" (76.2 cm) models A. 303/16" (76.6 cm) maximum
overall height B. 293/4" (75.6 cm) overall width C. For Noir models - 263/8"
(67 cm) For Rise models - 273/16" (69 cm) D. 231/4" (59.1 cm) maximum recessed depth E. 26" (66 cm) recessed height F. 48" (121.9 cm) flexible conduit length G. 287/16" (72.2 cm) maximum recessed width H. 12" (30.5 cm) from back of control panel to start of strain relief
7
Cabinet Dimensions - Single Ovens, Standard Installation
Single Ovens Installed in Cabinet
A
Product Dimensions - Double Ovens
H
G
F
B
D F
A
E
G E
C
27" (68.6 cm) models A. 27" (68.6 cm) minimum
cabinet width B. 23/16" (5.5 cm) top of cutout to
bottom of upper cabinet door C. 32" (81.3 cm) bottom of
cutout to floor D. 251/2" (64.8 cm) minimum
cutout width E. 11/2" (3.8 cm) minimum
bottom of cutout to top of cabinet door F. 28" (71.2 cm)* recommended cutout height G. 24" (60.7 cm) cutout depth
30" (76.2 cm) models A. 30" (76.2 cm) minimum
cabinet width B. 23/16" (5.5 cm) top of cutout to
bottom of upper cabinet door C. 32" (81.3 cm) bottom of
cutout to floor D. 281/2" (72.4 cm) minimum
cutout width E. 11/2" (3.8 cm) minimum
bottom of cutout to top of cabinet door F. 28" (71.2 cm)* recommended cutout height G. 24" (60.7 cm) cutout depth
*NOTE: The cutout height can be between 271/4" and 297/16" (69.2 cm and 74.8 cm) for single ovens.
NOTE: Contact service to get tall bottom vent shield for cutouts taller than 2811/16" (72.9 cm) to enhance installation.
B
D
C
27" (68.6 cm) models A. 53" (134.5 cm) maximum
overall height B. 27" (68.6 cm) overall width C. For Noir models - 263/8"
(67 cm) For Rise models - 273/16" (69 cm) D. 231/4" (59.1 cm) maximum recessed depth E. 483/4" (123.8 cm) recessed height F. 66" (167.6 cm) flexible conduit length G. 251/2" (64.7 cm) maximum recessed width H. 12" (30.5 cm) from back of control panel to start of strain relief
30" (76.2 cm) models A. 53" (134.5 cm) maximum
overall height B. 293/4" (75.6 cm) overall width C. For Noir models - 263/8"
(67 cm) For Rise models - 273/16" (69 cm) D. 231/4" (59.1 cm) maximum recessed depth E. 483/4" (123.8 cm) recessed height F. 66" (167.6 cm) flexible conduit length G. 287/16" (72.2 cm) maximum recessed width H. 12" (30.5 cm) from back of control panel to start of strain relief
8
Cabinet Dimensions - Double Ovens, Standard Installation
Double Ovens Installed in Cabinet A
B
D F
G E
C
Cabinet Dimensions - Single Ovens, Flush Installations
NOTE: This is an alternate option to install your product in the cabinet and obtain a flush look. For standard installation, refer section "Cabinet Dimensions - Single Ovens, Standard Installation".
A 25" (63.5 cm) minimum cutout depth is required.
Top and bottom gaps will be 1/8" (0.3 cm) gap above and below the product. Top and bottom gaps not required for installation. Exposed areas of the cabinet should be finished to match.
The front face of the cleats and platform will be visible and should be treated as a finished surface.
Single Ovens Installed in Cabinet
Front View
Side View
27" (68.6 cm) models A. 27" (68.6 cm) minimum
cabinet width B. 23/16" (5.5 cm) top of cutout to
bottom of upper cabinet door C. 143/4" (37.5 cm) bottom of
cutout to floor is recommended. 4"-143/4" (10.2 cm - 37.5 cm) bottom of cutout to floor is acceptable.
D. 251/2" (64.8 cm) minimum cutout width
E. 11/2" (3.8 cm) minimum bottom of cutout to top of cabinet door
F. 501/4" (127.6 cm)* recommended cutout height
G. 24" (60.7 cm) cutout depth
30" (76.2 cm) models A. 30" (76.2 cm) minimum
cabinet width B. 23/16" (5.5 cm) top of cutout to
bottom of upper cabinet door C. 143/4" (37.5 cm) bottom of
cutout to floor is recommended. 4"-143/4" (10.2 cm - 37.5 cm) bottom of cutout to floor is acceptable.
D. 281/2" (72.4 cm) minimum cutout width
E. 11/2" (3.8 cm) minimum bottom of cutout to top of cabinet door
F. 501/4" (127.6 cm)* recommended cutout height
G. 24" (60.7 cm) cutout depth
*NOTE: The cutout height can be between 50" and 523/16" (127 cm and 132.6 cm) for double ovens.
NOTE: Contact service to get tall bottom vent shield for cutouts taller than 503/8" (128 cm) to enhance installation.
27" (68.6 cm) Models
30" (76.2 cm) Models
A. 3/4" (1.9 cm) top cleat*
A. 3/4" (1.9 cm) top cleat*
B. 271/4" (69.2 cm) minimum width B. 301/4" (76.8 cm) minimum width
of flush inset cutout
of flush inset cutout
C. 257/8" (65.7 cm) minimum width C. 287/8" (73.3 cm) minimum width
of opening
of opening
D. 307/16" (77.3 cm) minimum height of flush inset cutout
D. 307/16" (77.3 cm) minimum height of flush inset cutout
E. 2911/16" (75.4 cm) recommended cutout height
E. 2911/16" (75.4 cm) recommended cutout height
F. 11/16" (1.7 cm) side cleat*
F. 11/16" (1.7 cm) side cleat*
G. 1/4" (0.6 cm) recommended G. 1/4" (0.6 cm) recommended
with foot. 15/16" to 11/8" (2.2 cm
with foot. 15/16" to 11/8" (2.2 cm
to 2.9 cm) allowable without
to 2.9 cm) allowable without
foot*
foot*
H. Recommended junction box location
H. Recommended junction box location
I. 45/8"-32" (11.7-81.3 cm) bottom I. 45/8"-32" (11.7-81.3 cm) bottom
of cutout to floor
of cutout to floor
J. 25" (63.5 cm) minimum depth J. 25" (63.5 cm) minimum depth
of cutout
of cutout
*Cleats and spacers must be recessed 13/8" (3.5 cm) from the front of the cabinet.
9
Single Ovens Undercounter - without cooktop installed above
Cabinet Dimensions - Double Ovens, Flush Installations
NOTE: This is an alternate option to install your product in the cabinet and obtain a flush look. For standard installation, refer section "Cabinet Dimensions - Double Ovens, Standard Installation".
A 253/8" (64.4 cm) minimum cutout depth is required.
Top and bottom gaps will be 1/8" (0.3 cm) gap above and below the product. Top and bottom gaps not required for installation. Exposed areas of the cabinet should be finished to match.
The front face of the cleats and platform will be visible and should be treated as a finished surface.
Double Ovens Installed in Cabinet
Front View
Side View
Front View
27" (68.6 cm) Models
30" (76.2 cm) Models
A. Recommended junction box location
A. Recommended junction box location
B. 3/4" (1.9 cm) top cleat*
B. 3/4" (1.9 cm) top cleat*
C. 271/4" (69.2 cm) minimum width C. 301/4" (76.8 cm) minimum width
of flush inset cutout
of flush inset cutout
D. 257/8" (65.7 cm) minimum width D. 287/8" (73.3 cm) minimum width
of opening
of opening
E. 291/4" (74.3 cm) minimum height of flush inset cutout
E. 291/4" (74.3 cm) minimum height of flush inset cutout
F. 281/2" (72.4 cm) recommended F. 281/2" (72.4 cm) recommended
cutout height
cutout height
G. 11/16" (1.7 cm) side cleat*
G. 11/16" (1.7 cm) side cleat*
H. 1/4" x 2" (6.4 mm x 5.1 cm) spacer the entire depth of the cabinet*
H. 1/4" x 2" (6.4 mm x 5.1 cm) spacer the entire depth of the cabinet*
I. 45/8" (11.7 cm) bottom of cutout I. 45/8" (11.7 cm) bottom of cutout
to floor
to floor
*Cleats and spacers must be recessed 13/8" (3.5 cm) from the front of the cabinet.
Top View
27" (68.6 cm) Models A. 2" (5.1 cm) spacer the entire
depth of the cutout* B. 25" (63.5 cm) depth of cutout C. 13/8" (3.5 cm) recess from front
of cabinet D. 11/16" (1.7 cm) side cleat*
30" (76.2 cm) Models A. 2" (5.1 cm) spacer the entire
depth of the cutout* B. 25" (63.5 cm) depth of cutout C. 13/8" (3.5 cm) recess from front
of cabinet D. 11/16" (1.7 cm) side cleat*
*Cleats and spacers must be recessed 13/8" (3.5 cm) from the front of the cabinet.
27" (76.2 cm) Models A. 3/4" (1.9 cm) top cleat* B. 271/4" (69.2 cm) minimum
width of flush inset cutout C. 257/8" (65.7 cm) minimum
width of opening D. 533/16" (135 cm) minimum
height of flush inset cutout E. 523/8" (133.1 cm)
recommended cutout height F. 11/16" (1.7 cm) side cleat* G. 1/4" (0.6 cm) recommended
with foot. 15/16" to 11/16" (2.2 cm to 2.7 cm) allowable without foot* H. Recommended junction box location I. 45/8"-143/4" (11.7-37.5 cm) bottom of cutout to floor J. 25" (63.5 cm) minimum depth of cutout
30" (76.2 cm) Models A. 3/4" (1.9 cm) top cleat* B. 301/4" (76.8 cm) minimum
width of flush inset cutout C. 287/8" (73.3 cm) minimum
width of opening D. 533/16" (135 cm) minimum
height of flush inset cutout E. 523/8" (133.1 cm)
recommended cutout height F. 11/16" (1.7 cm) side cleat* G. 1/4" (0.6 cm) recommended
with foot. 15/16" to 11/16" (2.2 cm to 2.7 cm) allowable without foot* H. Recommended junction box location I. 45/8"-32" (11.7-81.3 cm) bottom of cutout to floor J. 25" (63.5 cm) minimum depth of cutout
*Cleats and spacers must be recessed 13/8" (3.5 cm) from the front of the cabinet.
10
Approved Built-In Oven and Electric Radiant/Coil/Induction Cooktop Combinations or without cooktop installed above oven
Top View
27" (68.6 cm) Models A. 2" (5.1 cm) spacer the entire
depth of the cutout* B. 25" (63.5 cm) depth of cutout C. 13/8" (3.5 cm) recess from front
of cabinet D. 11/16" (1.7 cm) side cleat*
30" (76.2 cm) Models A. 2" (5.1 cm) spacer the entire
depth of the cutout* B. 25" (63.5 cm) depth of cutout C. 13/8" (3.5 cm) recess from front
of cabinet D. 11/16" (1.7 cm) side cleat*
*Cleats and spacers must be recessed 13/8" (3.5 cm) from the front of the cabinet.
Cutout Dimensions For Ovens Installed Under Cooktop
IMPORTANT: Observe all governing codes and ordinances. Cooktop must be approved for use over an oven. See cooktop Installation Instructions for cutout dimensions. Center the cooktop cutout over oven cutout.
Undercounter Installation (With Cooktop Installed Above):
Ovens approved for this type of installation have an approval label located on the top of the oven.
To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).
A. 24" (61 cm) cabinet depth B. 25" (63.5 cm) countertop
depth C. Recommended oven and
cooktop junction box locations D. Allow 5/8" (1.6 cm) for oven trim to overlap on each side. E. 273/4" (70.5 cm) minimum cutout height
F. 36" (91.4 cm) from cabinet base to countertop
G. 41/2" (11.4 cm) maximum from cabinet base with feet installed. If dimension "F" is greater than 36" (91.4 cm), dimension "G" can be increased the same difference for induction combinations
H. See Cutout Dimensions chart I. 313/8" (82.2 cm) from top of
countertop to bottom of cutout
CUTOUT DIMENSIONS (H)
Oven Size 24" (61 cm) 27" (68.6 cm) 30" (76.2 cm)
Minimum Oven Cutout Dimension 221/2" (57.2 cm) 251/2" (64.8 cm) 281/2" (72.4 cm)
For the approved model number combinations, refer to the undercounter label located on top of the oven chassis and on the bottom of the cooktop burner box.
NOTE: For undercounter installation, it is recommended that the junction boxes for oven and cooktop be located in the adjacent right or left cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the upper rear right or left corner of the side wall surface to pass the appliance cable through to the junction box.
11
Approved Built-In Oven and Gas Cooktop Combinations
Electrical Requirements
WARNING
A. 24" (61 cm) cabinet depth B. 1" (2.5 cm) clearance to
bottom of countertop C. 25" (63.5 cm) countertop
depth D. Recommended oven junction
box locations E. 1" (2.5 cm) clearance to
cabinet F. 273/4" (70.5 cm) minimum
cutout height G. Allow 5/8" (1.6 cm) for oven
trim to overlap on each side. H. 36" (91.4 cm) from cabinet
base to countertop
I. 313/8" (79.7 cm) from top of countertop to bottom of cutout
J. Gas line through wall 101/2" (26.7 cm) to center of cutout
K. 31/4" (8.3 cm) L. Gas line through floor 101/2"
(26.7 cm) to center of cutout M. 31/2" (8.9 cm) N. 41/2" (11.4 cm) maximum from
cabinet base with feet installed O. See Cutout Dimensions chart
CUTOUT DIMENSIONS (O)
Oven Size 24" (61 cm) 27" (68.6 cm) 30" (76.2 cm) 36" (91.4 cm)
Minimum Oven Cutout Dimension 221/2" (57.2 cm) 251/2" (64.8 cm) 281/2" (72.4 cm) 341/2" (87.6 cm)
For the approved model number combinations, refer to the undercounter label located on top of the oven chassis.
NOTE: For undercounter installation, it is recommended that the junction box for oven be located in the adjacent right or left cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the upper rear right or left corner of the side wall surface to pass the appliance cable through to the junction box.
The upper shaded areas are recommended locations for recessed junction box for 120 V grounded outlet for cooktop.
Lower shaded areas are recommended locations for flexible or rigid gas pipe installation. The gas connection on the cooktop is on the right (same location as "J" in the above diagram). The gas pipe can be installed on either side of the cutout, and either through the floor or through the wall. Refer to local codes regarding the use of gas lines.
Electrical Shock Hazard
Electrically ground appliance.
Failure to do so could result in death, fire, or electrical shock.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and the wire gauge are in accordance with local codes.
Check with a qualified electrical installer if you are not sure the oven is properly grounded.
This oven must be connected to a grounded metal, permanent wiring system.
Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances.
A copy of the above code standards can be obtained from: National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169-7471
CSA International 8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Electrical Connection
To properly install your oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial/rating plate. The model/serial/rating plate is located under the control panel on single ovens and under the control panel on the upper oven cavity on double ovens. See the following illustrations.
Single oven A. Model/serial/rating plate
Double oven A. Model/serial/rating plate
Models rated from 7.3 to 9.6 kW at 240 V (5.4 to 7.4 kW at 208 V) require a separate 40 A circuit. Models rated at 4.8 kW and below at 240 V (3.6 kW and below at 208 V) require a separate 20 A circuit.
12
PDFium PDFium
Related Documents
JennAir Electric Single Wall Oven Dimension Guide & Installation Specifications Comprehensive dimension guide and installation requirements for JennAir electric single wall ovens, including models JOESC330RL, JOESC330RM, JOESC530RL, JOESC530RM, JOESC730RL, and JOESC730RM. Features detailed diagrams and specifications for standard, flush, and under-cooktop installations, along with electrical requirements.
Jenn-Air Electric Double Wall Oven Installation Dimensions and Requirements Guide Detailed dimension guide for Jenn-Air 30-inch electric double wall ovens (JOEDC330RL, JOEDC330RM, JOEDC530RL, JOEDC530RM, JOEDC730RL, JOEDC730RM), covering standard and flush installation requirements, cabinet dimensions, and electrical specifications.
Jenn-Air Electric Combo Microwave/Wall Oven Dimension Guide Detailed dimension specifications and installation requirements for Jenn-Air electric combo microwave/wall ovens, including JOECC530RL, JOECC530RM, JOECC730RL, and JOECC730RM models. Covers standard and flush installations, electrical requirements, and cabinet dimensions.
Jenn-Air Electric Induction Cooktop Installation Instructions Comprehensive installation instructions for Jenn-Air 24", 30", and 36" electric induction cooktops, covering safety, requirements, tools, parts, and step-by-step procedures for installation.
JennAir JBSFS42NMX/48NMX Built-In Refrigerator Dimension Guide Comprehensive dimension and specification guide for JennAir JBSFS42NMX and JBSFS48NMX built-in refrigerators, covering exterior, interior, and compartment measurements, as well as electrical and installation requirements.
