Kwikset Powerbolt 2 Touchpad Keyless Entry

Parts in the Box

A - Latch, B - Strike, C - Mounting Plate, D - Exterior Assembly, E - Keys, F - Interior Assembly, G - Exterior Trim, H - Interior Trim, J - Interior Cover, K - Latch and Plate Screws, L - Interior Assembly Screws, M - Mounting Plate Screws, N - SmartKey Tool, P - Door Frame Screws

Tools Required

4 AA Batteries, Tape Measure, Phillips Screwdriver

Additional Tools (Depending on Application)

Hammer, Wood Block, Pliers

Kwikset Technical Support: 1-800-327-5625 | www.kwikset.com

1 Prepare the Door and Check Measurements

If drilling a new door, use the supplied template. Complete door drilling instructions are available at www.kwikset.com/doorprep.

• A Measure to confirm the door hole is 54 mm (2-1/8") or 38 mm (1-1/2").
• B Measure to confirm the backset is 60 or 70 mm (2-3/8" or 2-3/4").
• C Measure to confirm the door edge hole is 1" (25 mm).
• D Measure to confirm the door thickness is 35 mm or 44 mm (1-3/8" or 1-3/4").

Note: Additional door preparation may be necessary for doors with 38 mm (1-1/2") holes. Refer to drilling instructions at www.kwikset.com/doorprep.

2 Install the Latch and Strike

• A Hold the latch in front of the door hole, with the latch face flush with the door edge.
• B Is the slotted hole centered in the door hole?
  • Yes: Install the latch into the door with the supplied screws. Ensure the slotted hole is at the bottom of the latch.
  • No: Use a flathead screwdriver to lift the tabs on the rectangular faceplate collar to remove it from the latch. Install the latch into the door with the supplied screws. Ensure the slotted hole is at the bottom of the latch.
• C Install the strike on the door frame. Ensure the hole in the door frame is drilled at least 1" (25 mm) deep.
• D Align the tabs with the holes in the drive-through. Verify the drive-through fits snugly. Pull on the drive-through to test for a perfect fit. No adjustment is needed. Proceed to the next step. Turn the latch face to extend the latch.

IMPORTANT: Ensure the latch is fully retracted (in the unlocked position).

3 Prepare the Exterior Assembly and Mounting Plate (for doors with smaller holes)

What is the diameter of the hole in the door?

• Diameter is 54 mm (2-1/8"): No adjustment needed. Proceed to Step 4.
• Diameter is 38 mm (1-1/2"):
  • A Remove the adapter ring from the exterior assembly.
  • B 1. Remove the gasket. 2. Remove the adapter ring from the exterior assembly. 3. Reinstall the gasket, ensuring a tight seal.

Use pliers to remove the two tabs from the mounting plate.

4 Install the Exterior Assembly

• A Insert the cable under the latch.
• B IMPORTANT: Ensure the latch is fully retracted (in the unlocked position).
• C IMPORTANT: Hold the exterior assembly firmly on the outside of the door (or have a second person assist) for the following steps.
• D Insert the tailpiece through the slotted hole in the latch.
• E IMPORTANT: Ensure the tailpiece is in the horizontal position.
• F Insert the tailpiece through the center hole of the mounting plate and feed the cable through the bottom hole.
• G Secure the mounting plate with the supplied screws.
• H Insert the key to test the latch. If the latch does not extend or retract smoothly, adjust the screws.
• I Remove the key and check that the latch is in the unlocked position.

5 Install the Interior Assembly

• A Remove the interior cover.
• B Align the colored edges of the connectors and ensure the connection is firm.
• C Ensure the tailpiece is in the horizontal position. Install the interior assembly.
• D IMPORTANT: Rotate the turnpiece AWAY from the door edge and ensure the latch is fully retracted (in the unlocked position).
• E Install 4 AA batteries into the interior assembly. For best results, use new, non-rechargeable alkaline batteries. Ensure correct polarity. Note: The knob may turn on its own.
• F Secure the interior assembly with the supplied screws.
• G Test the smooth operation of the knob. If the knob does not turn, repeat steps 5E and 5F, ensuring the knob is turned away from the door edge.
• H Reinstall the interior cover and ensure the latch is in the unlocked position.

6 Set the Lock and Unlock Direction

• A With the door OPEN AND UNLOCKED, enter the following code to teach the lock the door's orientation: This is your default master code. 1. Press 0-0-0-0. 2. Press [lock symbol]. 3. Press 0. 4. Press [lock symbol]. You will hear 1 beep.
• B The latch will extend and retract. The deadbolt will beep and the keypad will turn green or red.
  • Green (with 2 beeps): The door has successfully learned the door's orientation. Proceed to step 6C.
  • Red (with 3 beeps): Ensure the door is unlocked and you are using a fresh set of batteries. Repeat step 6A.
• C Press the lock button. The latch will extend and lock. During normal operation, press the lock button to lock the door.
• D Enter the default user code (1-2-3-4). Press the lock button. The door will unlock. During normal operation, press the lock button after entering your user code to unlock the door.

IMPORTANT: It is recommended to replace the default master code and default user code with your own codes. See page 4.

7 Optional: Change the Key

Change the lock's key to work with the key you already have. Refer to the Smartkey key re-keying instructions supplied for more information.

8 Quick Setup and Use

Move quickly during programming. If no digits are pressed for 10 seconds, the touchscreen will turn off and you will need to restart the procedure.

A. How to Delete All User Codes

CAUTION: A user code is used to unlock the door, while a master code is a password to make changes to the lock functions.

1. Ensure your door is open and unlocked.
2. Enter your master code. For new installation, the default is 0-0-0-0.
3. Press [lock symbol]. You will hear 1 beep.
4. Press 5.
5. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.

For a new installation, the default user code 1-2-3-4 will be deleted. For subsequent instances, this action will delete all user codes on the lock. The lock can now only be operated by the key and the knob until a new user code is added in step B.

B. How to Add User Codes

A total of 6 user codes (and one temporary user code) can be programmed. Do not program a user code that is the same as your master code.

1. Ensure your door is open and unlocked.
2. Enter your master code. For new installation, the default is 0-0-0-0.
3. Press [lock symbol].
4. Press 1.
5. Press [lock symbol]. You will hear 1 beep.
6. Enter a new user code. It must be between 4 and 10 digits.
7. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.
8. Test the code: while your door is open, lock it. Enter your new User Code, then press [lock symbol]. The door should unlock.

C. How to Change Your Mastercode

The Master Code (MC) will not unlock your door. It is an additional security feature used to set up all functions. The default master code is 0-0-0-0. Replace this code with your own code.

1. Ensure your door is open and unlocked.
2. Enter your master code. For new installation, the default is 0-0-0-0.
3. Press [lock symbol].
4. Press 7.
5. Press [lock symbol]. You will hear 1 beep.
6. Enter a new master code. It must be between 4 and 10 digits.
7. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.

9 Additional Programming Features

How to Enable/Disable Auto-Lock

The auto-lock feature will lock the door 30 seconds after it is unlocked. This feature is disabled by default.

1. Ensure your door is open and unlocked.
2. Enter your existing master code.
3. Press [lock symbol]. You will hear 1 beep.
4. Press 1-1.
5. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.

How to Change the Auto-Lock Delay

You can adjust the auto-lock delay to 10, 20, 30, 40, or 50 seconds.

1. Ensure your door is open and unlocked.
2. Enter your existing master code.
3. Press [lock symbol]. You will hear 1 beep.
4. Press 1-3.
5. Press [lock symbol]. You will hear 1 beep.
6. For 10 seconds, press 1.
7. For 20 seconds, press 3.
8. For 30 seconds, press 5.
9. For 40 seconds, press 7.
10. For 50 seconds, press 9.
11. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.

How to Enable/Disable User Codes

If user codes are disabled (e.g., when you go on vacation), the lock can only be operated by the key and knob until they are re-enabled.

1. Ensure your door is open and unlocked.
2. Enter your existing master code.
3. Press [lock symbol]. You will hear 1 beep.
4. Press 1-7.
5. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.

How to Delete a Single User Code

The default user code is 1-2-3-4. Replace this code with your own code.

1. Ensure your door is open and unlocked.
2. Enter your existing master code.
3. Press [lock symbol]. You will hear 1 beep.
4. Press 3.
5. Press [lock symbol]. You will hear 1 beep.
6. Enter the user code you wish to delete.
7. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.
8. Test the code: While the door is open, lock the latch. Enter the user code, and press [lock symbol]. Ensure the latch does not unlock.

How to Restore Default Settings

This procedure will delete all user codes associated with the lock and restore the default master code (0-0-0-0) and user code (1-2-3-4).

1. Ensure your door is open and unlocked.
2. Enter the default master code (0-0-0-0).
3. Press [lock symbol]. You will hear 1 beep.
4. Press 0.
5. Press [lock symbol]. The latch will extend and retract to learn the door's orientation. If successful, the keypad will flash green and you will hear 2 beeps. If unsuccessful, the keypad will flash red and you will hear 3 beeps (ensure the door is open and unlocked and you are using a fresh set of batteries).
6. Test the lock: While the door is open and unlocked, press [lock symbol]. Ensure the door locks.
7. Test the default user code: Enter the default user code (1-2-3-4), and press [lock symbol]. Ensure the door unlocks.

The default programming code is 0-0-0-0. Replace this code with your own code. The default user code is 1-2-3-4. Replace this code with your own code.

How to Add a Temporary User Code

A temporary user code can only be used once and will be deleted immediately after use.

1. Ensure your door is open and unlocked.
2. Enter your existing master code.
3. Press [lock symbol]. You will hear 1 beep.
4. Press 1-9.
5. Press [lock symbol]. You will hear 1 beep.
6. Enter a new temporary user code. It must be between 4 and 10 digits.
7. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.

How to Enable/Disable Sound

If the deadbolt is silenced, you will not hear beeps during programming, normal operation, low battery indicators, or system alerts.

1. Ensure your door is open and unlocked.
2. Enter your existing master code.
3. Press [lock symbol]. You will hear 1 beep.
4. Press 1-5.
5. Press [lock symbol]. If successful, you will hear 2 beeps. If you hear 3 beeps, you were unsuccessful. Repeat step 1 slowly.

System Alerts

Troubleshooting

• The keypad does not lock or unlock the lock. Ensure the lock is programmed with at least one user code and that user codes are not disabled. If necessary, restore default settings.
• The keypad does not respond when its keys are pressed (no lights or beep sound). Ensure the cables are connected properly and that the batteries are new and installed correctly.
• The door can be closed with the lock button, but the user code will not open the door. Ensure the user code is correct and that the lock button is pressed after entering the user code. If the door still does not open, use a key to open the door. Contact technical support for further assistance to resolve the issue.
• When the door is closed and the lock button is pressed to lock the door, the lock beeps 3 times. When the door is open and the lock button is pressed to lock the door, the lock does not beep. Ensure the hole in the door frame is drilled at least 1" (25 mm) deep. Ensure the strike is aligned with the latch. If necessary, reposition the strike.

Important Safeguards

1. Read all instructions.
2. Familiarize yourself with all warning and caution definitions.
3. Remind all family members of the safety precautions.
4. Limit access to the interior assembly of the lock and routinely verify the settings to ensure they have not been altered without your knowledge.
5. Protect your user codes and master code.
6. Dispose of batteries according to local laws and regulations.

CAUTION: Prevent unauthorized entry. This lock contains a default master code and user code. After installation and setup, replace both codes with your own codes. Because anyone with access to the interior assembly can reset the lock and change the user codes, you must restrict access to the back panel and routinely check both codes to ensure your own user codes have not been altered without your knowledge.

WARNING: Kwikset makes no representations that this lock can provide complete security by itself. This lock can be defeated by forcible or technical means, or evaded by entry on another part of the property. No lock can be substituted for caution, awareness of your surroundings, and common sense. Hardware may be purchased from locksmiths in varying degrees of performance to fit the application. To enhance security and reduce risk, you should consult with a qualified locksmith or other security professional.

©2018 Spectrum Brands, Inc.